• International Journal of Automotive Technology
• /
• v.8 no.2
• /
• pp.249-258
• /
• 2007

This paper proposes a method that can be used for the resistance estimation of a PWM (Pulse Width Modulation)-driven solenoid. By using estimated solenoid resistance, the PWM duty ratio was compensated to be proportional to the solenoid current. The proposed method was developed for use with EHB (Electro-Hydraulic Braking) systems, which are essential features of the regenerative braking system of many electric vehicles. Because the HU (Hydraulic Unit) of most EHB systems performs not only ABS/TCS/ESP (Electronic Stability Program) functions but also service braking function, the possible duration of continuous solenoid driving is so long that the generated heat can drastically change the level of solenoid resistance. The current model of the PWM-driven solenoid is further developed in this paper; from this a new resistance equation is derived. This resistance equation is solved by using an iterative method known as the FPT (fixed point theorem). Furthermore, by taking the average of the resistance estimates, it was possible to successfully eliminate the effect of measurement noise factors. Simulation results showed that the proposed method contained a sufficient pass-band in the frequency response. Experimental results also showed that adaptive solenoid driving which incorporates resistance estimations is able to maintain a linear relationship between the PWM duty ratio and the solenoid current in spite of a wide variety of ambient temperatures and continuous driving.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.1
• /
• pp.81-88
• /
• 2007

In this paper, a new single-phase utility-interactive inverter system for residential power generation with fuel cell is proposed. The proposed inverter system is not only capable of working in both stand-alone and grid-connected mode, but also ensures smooth and automatic transfer between the two modes of operation. The proposed control method has little steady-state error and good transient response characteristic. Also, the control method can be implemented using low-cost, fixed point DSP since it has simpler structure, smaller amount of calculation, and smaller number of sensors. The controller for the proposed utility-interactive inverter system is described, and the validity is verified through simulation and experiment.

• Bulletin of the Korean Chemical Society
• /
• v.5 no.4
• /
• pp.162-167
• /
• 1984

Equilibrium and dynamical behaviors of an n-alkane poymer (decane) in solution have been investigated by a molecuar dynamics simulation method. The polymer is assumed to be a chain of elements $(CH_2)$ interconnected by bonds having a fixed bond length and bond angle, but esch bond of the polymer is allowed to execute hindered internal rotation. The calculation explicitly considers the molecular naturer of solvent by including the intermolecular interactions between slovent-solvent molecules and chain element-solvent molecule. We present the results of calculations on (1) equilibrium properties (the solvent molecule-chain element pair correlation function, chain element-chain element pair correlation function, the mean square end-to-end distance and the mean square radius of gyration of the polymer) and (2) dynamic properties (four different autocorrelation functions, namely, the autocorrelation functions for the end-to-end distance and the radius of gyration, and the velocity autocorrelation functions for the center of mass and the end point of the chain). We found that the physical properties of the polymer chain depends sensitively on temperature. Comparison of the present work with other authors' results is also presented.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.16 no.4
• /
• pp.1187-1208
• /
• 2022

One of the main goals of wireless sensor networks (WSNs) is to utilize the energy of sensor nodes effectively and maximize the network lifetime. Thus, this paper proposed a routing protocol for WSNs based on virtual force disturbing mobile Sink node (VFMSR). According to the number of sensor nodes in the cluster, the average energy and the centroid factor of the cluster, a new cluster head (CH) election fitness function was designed. At the same time, a hexagonal fixed-point moving trajectory model with the best radius was constructed, and the virtual force was introduced to interfere with it, so as to avoid the frequent propagation of sink node position information, and reduce the energy consumption of CH. Combined with the improved ant colony algorithm (ACA), the shortest transmission path to Sink node was constructed to reduce the energy consumption of long-distance data transmission of CHs. The simulation results showed that, compared with LEACH, EIP-LEACH, ANT-LEACH and MECA protocols, VFMSR protocol was superior to the existing routing protocols in terms of network energy consumption and network lifetime, and compared with LEACH protocol, the network lifetime was increased by more than three times.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.1047-1050
• /
• 1998

This paper describes an advanced prototype of voltage-fed zero voltage soft-switching PWM resonant inverter with an active voltage clamped capacitor, which is put into practice for high-frequency high-power induction-heated appliances. This application-specific quasi-resonant inverter using the latest generation IGBTs for soft-switching can regulate its output power under a principle of a fixed frequency ZVS-PWM strategy. Its operating principle and unique features are presented as compared with a conventional quasi-resonant ZVS inverter for induction-heated cooker, together with its power regulation characteristics on the basis of its simulation and experimental results. The steady-state performances of this inverter developed for multi-burner type induction-heated food cooking appliance are evaluated and discussed from a practical point of view.

• Journal of Advanced Navigation Technology
• /
• v.21 no.4
• /
• pp.377-385
• /
• 2017

The solar cell need the characteristic interpreting because the solar cell changes greatly according to the isolation, temperature and load in the photovoltaic development. Moreover, to get many energy in photovoltaic development need the position tracking of the sun according to the environment change. Also, The solar cells should be operated at the maximum power point. In this paper, I used microprocessor and sensor and designed to improve the efficiency of the photovoltaic system the photovoltaic position tracker device, and compared the normal photovoltaic system of fixed form with the photovoltaic system of solar position tracked form. Moreover, compared the catalogue of solar cell module and the simulation through a mathematics modelling with the solar cell's characteristic interpreting and composed an power conversion system with boost converter and voltage source inverter. Used the constant voltage control method for maximum power point tracking in boost converter control and, used the SPWM(Sinusoidal Pulse Width Modulation) control method in inverter control. The result was less then 5% when compared the catalogue of solar cell module and the simulation through a mathematics modelling. The boost rate of boost converter was similar to 167 % with the simulation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.4
• /
• pp.173-179
• /
• 2002

This paper describes an equalizer using the DFE (Decision Feedback Equalizer) structure, CMA (Constant Modulus Algorithm) and LMS (Least Mean Square) algorithms. The DFE structure has better channel adaptive performance and lower BER than the transversal structure. The proposed equalizer can be used for 16/64 QAM modems. We employ high speed multipliers, square logics and many CSAs (Carry Save Adder) for high speed operations. We have developed floating-point models and fixed-point models using the COSSAP$\^$TM/ CAD tool and developed VHDL filter. The proposed equalizer shows low BER in multipath fading channel. We have performed models. From the simulation results, we employ a 12 tap feedback filter and a 8 tap feedforward logic synthesis using the SYNOPSYS$\^$TM/ CAD tool and the SAMSUNG 0.5$\mu\textrm{m}$ standard cell library (STD80) and verified function and timing simulations. The total number of gates is about 130,000.

• Journal of Korea Multimedia Society
• /
• v.3 no.4
• /
• pp.356-364
• /
• 2000

Block based fast motion estimation algorithm use the fixed search pattern to reduce the search point, and are based on the assumption that the error in the mean absolute error space monotonically decreases to the global minimum. Therefore, in case of many local minima in a search region we are likely to find local minima instead of the global minimum and highly rely on the initial search points. This situation is evident in the motion boundary. In this paper we define the candidate regions within the search region using the motion information of the neighbor blocks and we propose the multiple local search method (MLSM) which search for the solution throughout the candidate regions to reduce the possibilities of isolation to the local minima. In the MLSM we mark the candidate region in the search point map and we avoid to search the candidate regions already visited to reduce the calculation. In the simulation results the proposed method shows more excellent results than that of other gradient based method especially in the search of motion boundary. Especially, in PSNR the proposed method obtains similar estimate accuracy with the significant reduction of search points to that of full search.

• Journal of IKEEE
• /
• v.25 no.4
• /
• pp.710-715
• /
• 2021

Power line signal can show disturbances due to various causes. Typical anomalies are temporary sag/swell of the amplitude, flat topped signal, and harmonic distortions. The disturbances need to be detected and treated properly for the quality of the power signal. In this study, the power disturbances are detected using the inflection points (IP). The inflection points are defined as points where local maxima/minima or the slope changes occur. The power line signal has a fixed IP pattern since it is basically sinusoidal, and it may have additional inflection points if there is any disturbance. The disturbance is detected by comparing the IP patterns between the normal signal and distorted signal. In addition, by defining a cost function, the time instant where the disturbance happens can be decided. The computer simulation shows that the proposed method is useful for the detection of various disturbances. The simple sag or swell signal only shows the amplitude changes at the detected inflection points. However, the flat top signal and harmonically distorted signal produce additional inflection points and large values in the cost function. These results can be exploited for the further processing of disturbance classification.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.12A
• /
• pp.1922-1931
• /
• 1999

A multicast traffic’s feature is the function of providing a point to multipoints cell transmission, which is emerging from the main function of ATM switch. However, when a conventional point-to-point switch executes a multicast function, the excess load is occurred because unicast cell as well as multicast cell passed the copy network. Additionally, due to the excess load, multicast cells collide with other cells in a switch. Thus a deadlock that losses cells raises, extremely diminishes the performance of switch. An input queued switch also has a defect of the HOL (Head of Line) blocking that less lessens the performance of the switch. In the proposed multicast switch, we use shared memory switch to reduce HOL blocking and deadlock. In order to decrease switch’s complexity and cell's processing time, to improve a throughput, we utilize the method that routes a cell on a separated paths by traffic pattern and the scheduling algorithm that processes a maximum 2N cell at once in the control part. Besides, when cells is congested at an output port, a cell loss probability increases. Thus we use the Output Memory (OM) to reduce the cell loss probability. And we make use of the method that stores the assigned memory (UM, MM) with a cell by a traffic pattern and clears the cell of the Output memory after a fixed saving time to improve the memory utilization rate. The performance of the proposed switch is executed and compared with the conventional policy under the burst traffic condition through both the analysis based on Markov chain and simulation.