• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.869-875
• /
• 2009

Safety is a big issue in the construction sites. For safe and secure management, tracking locations of construction resources such as labors, materials, machineries, vehicles and so on is important. The materials, machineries and vehicles could be controlled by computer, whereas the movement of labors does not have fixed pattern. So, the location and movement of labors need to be monitored continuously for safety. In general, Global Positioning System(GPS) is an opt solution to obtain the location information in outside environments. But it cannot be used for indoor locations as it requires a clear Line-Of-Sight(LOS) to satellites Therefore, indoor location monitoring system could be a convenient alternative for environments such as tunnel and indoor building construction sites. This paper presents a case study to investigate feasibility of Wi-Fi based indoor location monitoring system in construction site. The system is developed by using fingerprint map of gathering Received Signal Strength Indication(RSSI) from each Access Point(AP). The signal information is gathered by Radio Frequency Identification (RFID) tags, which are attached on a helmet of labors to track their locations, and is sent to server computer. Experiments were conducted in a shield tunnel construction site at Guangzhou, China. This study consists of three phases as follows: First, we have a tracking test in entrance area of tunnel construction site. This experiment was performed to find the effective geometry of APs installation. The geometry of APs installation was changed for finding effective locations, and the experiment was performed using one and more tags. Second, APs were separated into two groups, and they were connected with LAN cable in tunnel construction site. The purpose of this experiment was to check the validity of group separating strategy. One group was installed around the entrance and the other one was installed inside the tunnel. Finally, we installed the system inner area of tunnel, boring machine area, and checked the performance with varying conditions (the presence of obstacles such as train, worker, and so on). Accuracy of this study was calculated from the data, which was collected at some known points. Experimental results showed that WiFi-based indoor location system has a level of accuracy of a few meters in tunnel construction site. From the results, it is inferred that the location tracking system can track the approximate location of labors in the construction site. It is able to alert the labors when they are closer to dangerous zones like poisonous region or cave-in..

• The Korea Journal of Herbology
• /
• v.27 no.2
• /
• pp.1-16
• /
• 2012

Objective : To investigate the current status of prescription drugs in Oriental medical institutes and to draw up a future plan for the revitalization of Oriental medical health insurance, this survey has been performed. Method : The survey has been made with 321 doctors working at Oriental medical institutes in Daegu and Kyungbuk areas for a period of 3 month from June 1, 2010 until September 1, 2010. Result : 1. When it comes to the current status of the use of herbal drugs in Oriental Health insurance, most of doctors surveyed prescribe insurance drugs, and they prescribe insurance drugs to patients, who are less than 20% of total patients visiting their clinics. 2. The awareness of Herbal Health Care Drugs is investigated. When it comes to the understanding of the difference between insurance drugs(powder type drugs) and granular type drugs, doctors admit that they differ only in one aspect, whether or not their being covered by health insurance. Based on the survey results on the understanding of insurance coverage of granular type drugs, doctors, even though they long for granular type drugs to be accepted as insurance drugs, are worrying whether the number of outpatients might dwindle due to increased insurance co-payments. They also point out that the biggest obstacles in the expansion of the granular type drugs as insurance drugs are the lack of understanding of the government and the objection of the Health Insurance Review and Assesment service (HIRA) for fear of increased insurance claims. 3. Upon investigation on Oriental medicine doctors' understandings of herbal pharmaceutical industry, it is found that doctors' responses on pharmaceutical industry are not all positive ones('new product development and neglect of R&D infrastructure' and 'smallness of industry'). When it is investigated what area needs the greatest improvement in herbal pharmaceutical industry, 'securing sufficient capital, good manufacturing, and strengthening quality control', is the highest. 4. When it is asked what are the most needed in order to improve herbal health insurance medicine, responses such as 'the increase in the accessibility to and the utilization of Oriental medical clinics through the diversification of the means of prescriptions', 'the improvement of insurance benefits(cap adjustments)', 'increase the proportion of high quality medicinal plants', 'the ceiling of co-payments(deductible) at 20,000 won or more', 'expansion of the choices of formulations', 'formulational expansions of tablets and pills', and finally 'admittance and expansion of granular type drug as insurance drug' are the highest. 5. Upon investigating the general characteristics of the current status of the usage of Oriental health care herbal drugs, the followings are observed. First, the frequency of use of health insurance drugs by the doctors who use health insurance with general characteristics shows similar differences in case of total monthly sales amount (p<0.001), average number of daily patients (p<0.05). Secondly, as to the willingness of the expanded usage of insurance drugs, similar differences are observed in case of total monthly sales amount (p<0.05). 6. Upon investigating the general characteristics of the perception of Herbal health care drugs, the followings are observed. First, inspecting general characteristics and insurance claims due to increased co-payments(deductible amount) reveals similar differences in case of working period (p<0.01) and in case of total monthly sales amount (p <0.01). Secondly, inspecting general characteristics and the obstacles that hinder granular type drugs from being accepted as health care insurance drugs shows similar differences in case of working period (p<0.05). 7. Upon investigating the general characteristics of the understanding of Oriental Herbal pharmaceutical companies, the followings are observed. First, opinions on the general characteristics of pharmaceutical companies, when examined with variance analysis, shows similar differences in case of total monthly sales amount (p<0.05). Secondly, when opinions are examined on general characteristics and the problems of herbal pharmaceutical companies, similar differences are found in case of working period (p<0.01) and in case of total monthly sales amount (p<0.001). Lastly, opinions on the general characteristics and reforms of pharmaceutical companies, similar differences are observed in case of working period (p<0.001). 8. Upon investigating the general characteristics of the improvement of insurance Herbal drugs, the followings are observed. First, regarding general characteristics and insurance benefits, similar differences are observed in case of working period (p<0.05), in case of total monthly sales amount (p<0.05), and in case of average number of daily patients (p<0.01). Secondly, opinions on the general characteristics and the needs for the improvement of Herbal insurance drugs are examined in 5 different aspects, which are the approval of granular type drugs as insurance drugs, the expanded practices of the number of prescription insurance drugs, the needs of a variety of formulations, the needs of TFT of which numbers of Oriental medical doctors are members for the revision of the existing system, and the needs of adjusting the current ceiling of the fixed amount and the fixed rate. When processed by the analysis of variance, the results show similar differences in case of average number of daily patients (p<0.01). Conclusion : From the results of this study the first measures to take are, to reform overall insurance benefit system, including insurance co-payment system(fixed rate cap adjustment), to expand the number of the herbal drugs to be prescribed matching with insurance benefit accordingly, and to revitalize herbal medicine insurance system through the change of various formulations. In addition, it is recommended to improve the effectiveness of herbal medicine by making plans to enhance the efficacy of herbal medicine and by enabling small pharmaceutical companies to outgrow themselves.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.2
• /
• pp.191-198
• /
• 2009

Statement of problem: Ceramics have been important materials for the restoration of teeth. The demands of patients for tooth-colored restorations and the availability of various dental ceramics has driven the increased use of new types of dental ceramic materials. Improved physical properties of theses materials have expanded its use even in posterior crowns and fixed partial dentures. However, ceramic still has limitation such as low loading capability. This is critical for long-span bridge, because bridge is more subject to tensile force. Purpose: The wire reinforced ceramic was designed to increase the fracture resistance of ceramic restoration. The purpose of this study was to evaluate the fracture resistance of wire reinforced ceramic. Material and methods: Heat pressed ceramic(ingot No.200 : IPS Empress 2, Ivoclar Vivadent, Liechtenstein) and Ni-Cr wire(Alfa Aesar, Johnson Matthey Company, USA) of 0.41 mm diameter were used in this study. Five groups of twelve uniform sized ceramic specimens(width 4 mm, thickness 2 mm, length 15 mm) were fabricated. Each group had different wire arrangement. Wireless ceramic was used as control group. The experimental groups were divided according to wire number and position. One, two and three strands of wires were positioned on the longitudinal axis of specimen. In another experimental group, three strands of wires positioned on the longitudinal axis and five strands of wires positioned on the transverse axis. Three-point bending test was done with universal testing machine(Z020, Zwick, Germany) to compare the flexural modulus, flexural strength, strain at fracture and fracture toughness of each group. Fractured ceramic specimens were cross-sectioned with caborundum disc and grinded with sandpaper to observe interface between ceramic and Ni-Cr wire. The interface between ceramic and Ni-Cr wire was analyzed with scanning electron microscope(JSM-6360, JEOL, Japan) under platinum coating. Results: The results obtained were as follows: 1. The average and standard deviation in flexural modulus, flexural strength and fracture toughness showed no statistical differences between control and experimental groups. However, strain was significantly increased in wire inserted ceramics(P<.001). 2. Control group showed wedge fracture aspects across specimen, while experimental groups showed cracks across specimen. 3. Scanning electron microscopic image of cross-sectioned and longitudinally-sectioned specimens showed no gap at the interface between ceramic and Ni-Cr wire. Conclusion: The results of this study showed that wire inserted ceramics have a high strain characteristic. However, wire inserted ceramics was not enough to use at posterior area of mouth in relation to flexural modulus and flexural strength. Therefore, we need further studies.

• Economic and Environmental Geology
• /
• v.55 no.4
• /
• pp.377-388
• /
• 2022

Laboratory-scale experiments were performed to identify the As removal mechanism of the residual slag generated after the mineral carbonation process. The residual slags were manufactured from the steelmaking slag (blast oxygen furnace slag: BOF) through direct and indirect carbonation process. RDBOF (residual BOF after the direct carbonation) and RIBOF (residual BOF after the indirect carbonation) showed different physicochemical-structural characteristics compared with raw BOF such as chemical-mineralogical properties, the pH level of leachate and forming micropores on the surface of the slag. In batch experiment, 0.1 g of residual slag was added to 10 mL of As-solution (initial concentration: 203.6 mg/L) titrated at various pH levels. The RDBOF showed 99.3% of As removal efficiency at initial pH 1, while it sharply decreased with the increase of initial pH. As the initial pH of solution decreased, the dissolution of carbonate minerals covering the surface was accelerated, increasing the exposed area of Fe-oxide and promoting the adsorption of As-oxyanions on the RDBOF surface. Whereas, the As removal efficiency of RIBOF increased with the increase of initial pH levels, and it reached up to 70% at initial pH 10. Considering the PZC (point of zero charge) of the RIBOF (pH 4.5), it was hardly expected that the electrical adsorption of As-oxyanion on surface of the RIBOF at initial pH of 4-10. Nevertheless it was observed that As-oxyanion was linked to the Fe-oxide on the RIBOF surface by the cation bridge effect of divalent cations such as Ca²⁺, Mn²⁺, and Fe²⁺. The surface of RIBOF became stronger negatively charged, the cation bridge effect was more strictly enforced, and more As can be fixed on the RIBOF surface. However, the Ca-products start to precipitate on the surface at pH 10-11 or higher and they even prevent the surface adsorption of As-oxyanion by Fe-oxide. The TCLP test was performed to evaluate the stability of As fixed on the surface of the residual slag after the batch experiment. Results supported that RDBOF and RIBOF firmly fixed As over the wide pH levels, by considering their As desorption rate of less than 2%. From the results of this study, it was proved that both residual slags can be used as an eco-friendly and low-cost As remover with high As removal efficiency and high stability and they also overcome the pH increase in solution, which is the disadvantage of existing steelmaking slag as an As remover.

• The Journal of the Korean Society for Microbiology
• /
• v.20 no.1
• /
• pp.91-102
• /
• 1985

The advantages of enzyme-linked immunosorbent assay(ELISA) are its senstivity and simplicity in detecting IgG, IgM and IgA antibody. To apply ELISA to diagnosis of typhoid fever, antigen such as lipopolysaccharide of Salmonella typhi or killed whole cell must be coated on solid phase. It is easy to coat lipopolysaccharide on ELISA plate but troublesome to purify it. As it is easy to obtain the killed whole cells, the development of the appropriate method by which those antigens of S. typhi are optimally coated on solid phase is needed. To establish the appropriate method, carbonate buffer, methanol or poly-L-lysine was applied as binding substance on polystyrene or polyvinylchloride plate as solid phase when the killed whole cell antigens of S. typhi varided as follows: $10^6$, $10^7$, $10^8$ and $10^9\;cell/ml$. The criteria of the optimal method were determined as follows: 1. The optical density of positive sera is above 1.0(0.6 in IgM) at 1:10 serum dilution and is 0.3(0.2 in IgM) higher than that of negative sera: 2. The O.D. of sera is flat or lowering according to serum dilution: 3. It must be that the O.D. of negative sera is lower than 0.2 at the point of serum dilution where the O.D. of positive sera is higher than 1.0(0.5 in IgM). The results obtained were summarized as follows: 1. The methods which fitted the above criteria were to use poly-L-lysine as binding substance, polyvinylchloride plate as solid phase and $10^7\;cell/ml$ as antigen concentration of S. typhi(poly-L-lysine/polyvinylchloride/$10^7$) and poly-L-lysine/polyvinylchloride/$10^8$ in detecting IgG antibody, methanol/polystyrene/$10^9$, poly-L-lysine/polyvinylchloride/$10^8$ and poly-L-lysine/polyvinylchloride/$10^9$ in IgM and carbonate buffer/polystyrene/$10^8$, carbonate buffer/polystyrene/$10^9$, methanol/polystyrene/$10^8$, methanol/polyvinylchloride/$10^8$, methanol/polyvinylchloride/$10^9$, poly-L-lysine/polyvinylchloride/$10^8$ and poly-L-lysine/polyvinylchloride/$10^9$ in IgA. 2. The coaling method using poly-L-lysine, polyvinylchloride plate and $10^8\;cell/ml$ was best to assay IgG, IgM and IgA antibody all in one. By this method, to assay the each immunoglobulin calss with an appropriate fixed serum dilution, 1:320 dilution was best.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.11 s.353
• /
• pp.128-140
• /
• 2006

In the IEEE 802.16 Wireless MAN standard specifies the air interface of fixed point-to-multipoint broadband wireless access systems providing multiple services. Among the service classes supported between the base station and subscriber stations in the wireless MAN, the best effort service class is ranked on the lowest position in priority and is assisted by a MAC scheme based on reservation ALOHA. The wireless MAN standard, however, does not reveal every detail of the MAC scheme but only describes the skeleton of the MAC scheme. Focusing on the amount of resource that a subscriber demands by a request and the amount of resource that the base grants to a request we thus present a number of resource demand rules and resource grant rules. Also, we construct a candidate MAC scheme by implanting a pair of resource demand and grant rules into the skeleton of the MAC scheme. Meanwhile a difficult situation for the best effort service is expected wherein only scarce resource is available after most of the resource is already preempted by other services. Perceiving such a situation, we evaluate the throughput and delay performance of each candidate MAC scheme. Especially we develop an analytical method to approximately calculate the throughput in the saturated environment. From the numerical results, we observe that the candidate MAC scheme which adopts the non-gated exhaustive demand rule paired with the full grant rule attains superior performance at the expense of the fairness.

• Journal of Energy Engineering
• /
• v.23 no.3
• /
• pp.125-131
• /
• 2014

In order to increase landfill gas (LFG) production with food waste leachate, this study was confirmed to be acidogenetic conditions for landfill site injection. Thereby, it was conducted for acidogenetic treatments to determine the decrease in viscosity and VFA production. After acidogenesis treatments, solubility of food waste leachate increased approximately 15%, and as a result, UASB and CSTR were similar by reactor type using the change of retention time. Based on the result of the change in viscosity by reactor type, efficiency of UASB showed approximately 11.38% of higher decrease in viscosity as $76.95{\pm}3.27%$ vs. CSTR. Also, VFA production showed the higher increase of 2.01 times (UASB) and 1.76 times (CSTR) respectively at the point of increasing retention time from 3 to 5 days. From the above results, efficiency of UASB in a reactor was relatively higher because large molecular lead to longer retention time than small molecular due to having screen effect in the fixed media.

• Korean Journal of Applied Biomechanics
• /
• v.18 no.2
• /
• pp.95-104
• /
• 2008

The purpose of this study was to investigate kinematic coordination and control of lower segments in skill process. For the investigation, we examined the difference of resultant linear velocity of segments and angle vs angle graph. Novice subjects were 9 male middle school students who has never been experienced a taekwondo and expert subjects were 7 university taekwondo players. We analyzed kinematic variables of Dollyochagi motion through videographical analysis and the conclusion were as follows. 1. Examining the graph of novice subjects' maximal resultant linear velocity of the thigh, shank, and foot segment, as it gets closer to the end of the training, the maximal resultant linear velocity in each segment increased. Statistical analysis showed the following results; thigh segment caused the increase of speed, using the trunk segment's momentum in the latter term of learning, while the shank segment utilized the momentum of the adjacent proximal segment at the beginning of learning, and the foot segment in the middle of learning. 2. Until the point where the knee joint angle is minimum, as the novice group learn the skill, the flexion of knee and hip joints has changed into the form of coordination pattern in phase. On the other hand, the expert group showed continual coordination pattern in phase that the movement sequences were smooth. From the knee joint maximal flexion to impact timing, all novice and expert groups showed coordination pattern out of phase. 3. From the knee joint maximal flexion to impact timing, the ankle joint was fixed and the knee joint was extended to all the novice stages and expert subjects.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.2
• /
• pp.250-262
• /
• 2007

Statement of problem: It was reported high success rate of implant-supported fixed prostheses using with $5{\sim}6$ implants on anterior mandible. Recently, immediate loading protocol was focused to overcome disadvantages of classic 2-stage delayed loading protocol. Purpose: This clinical study was to evaluate stability changes with time of immediately loaded and delayed loaded implants in edentulous mandible and to compare stability changes with time according to implantation sites. Materials and methods: Five or six implants were placed on anterior mandible depending on the arch shape. The immediately loading group was consisted of 8 patients received their prostheses within $24{\sim}48$ hours after implantation. The delayed loading group was consisted of 8 patients received their definitive prostheses following classical prosthetic procedures after a healing period of 3 months. All patients were recalled every 6 months for check-up. The evaluations of radiographic examination, ISQ value measurement and recording of complication were done. To evaluate marginal bone level, intraoral periapical radiographs were taken with long cone paralleling technique. At every evaluation recall, all prostheses were removed and ISQ values were measured with OsstellTM on individual implants. Results: 1. None of implants was failed. All implants showed stable marginal bone levels and ISQ values. 2. Marginal bone level changes with time showed statistically significant difference between immediately loading group and delayed loading group (P<0.001). 3. ISQ value changes with time did not show statistically significant difference between immediately loading group and delayed loading group (P=0.079). ISQ value decreased with time in both groups, however, all implants showed stable ISQ value at 30 months-recall evaluation. 4. Marginal bone level changes with time did not show statistically significant differences among implantation sites (P=0.604). 5. ISQ value changes with time showed statistically significant differences among implantation sites (P=0.047). ISQ values of most posterior implants decreased with time comparing to other implants. Conclusion: Although the marginal bone level of the terminal abutment didn't different with the other implants, ISQ value of the terminal abutment was lower than that of the other implants. Therefore, further clinical evaluation would be needed in this point of view.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3587-3593
• /
• 2009

Nowadays, the PV systems have been focused on the interconnection between the power source and the grid. The PV inverter, either single-phase or three-phase, can be considered as the core of the whole system because of an important role in the grid-interconnecting operation. An important issue in the inverter control is the load current regulation. In the literature, the Proportional+Integral (PI) controller, normally used in the current-controlled Voltage Source Inverter (VSI), cannot be a satisfactory controller for an ac system because of the steady-sate error and the poor disturbance rejection, especially in high-frequency range. By comparison with the PI controller, the Proportional+Resonant (PR) controller can introduce an infinite gain at the fundamental ac frequency; hence can achieve the zero steady-state error without requiring the complex transformation and the dq-coupling technique. In this paper, a PR controller is designed and adopted for replacing the PI controller. Based on the theoretical analyses, the PR controller based control strategy is implemented in a 32-bit fixed-point TMS320F2812 DSP and evaluated in a 3kW experimental prototype Photovoltaic (PV) power conditioning system (PCS). Simulation and experimental results are shown to verify the performance of implemented control scheme in PV PCS.