• 한국초전도ㆍ저온공학회논문지
• /
• 제16권1호
• /
• pp.1-5
• /
• 2014

We calculated the resonance tunneling energy band in the BCS gap for Type-II superconductor in which periodic potential is generated by external magnetic flux. In this model, penetrating magnetic flux was assumed to be in a fixed lattice state which is not moving by an external force. We observed the existence of two subbands when we used the same parameters as for the $Nd_{1.85}Ce_{0.15}CuO_X$ thin film experiment. The voltages at which the regions of negative differential resistivity (NDR) started after the resonant tunneling ended were in a good agreement with the experimental data in the field region of 1 T - 2.2 T, but not in the high field regions. Discrepancy occurred in the high field region is considered to be caused by that the potential barrier could not be maintained because the current induced by resonant tunneling exceeds the superconducting critical current. In order to have better agreement in the low field region, more concrete designing of the potential rather than a simple square well used in the calculation might be needed. Based on this result, we can predict an occurrence of the electromagnetic radiation of as much difference of energy caused by the 2nd order resonant tunneling in which electrons transit from the 2nd band to the 1st band in the potential wells.

• 제어로봇시스템학회논문지
• /
• 제19권5호
• /
• pp.481-487
• /
• 2013

This paper presents an FIR (Finite Impulse Response) fixed-interval smoothing filter for fast and exact estimating state variables of a discrete nonlinear system with modeling uncertainty. Conventional IIR (Infinite Impulse Response) filter and smoothing filter can estimate state variables of a system with an exact model when the system is observable. When there is an uncertainty in the system model, however, conventional IIR filter and smoothing filter may cause large errors because the filters cannot estimate the state variables corresponding to the uncertain model exactly. To solve this problem, FIR filters that have fast estimation properties and have robustness to the modeling uncertainty have been developed. However, there is time-delay estimation phenomenon in the FIR filter. The FIR smoothing filter proposed in this paper makes up for the drawbacks of the IIR filter, IIR smoothing filter, and FIR filter. Therefore, the FIR smoothing filter has good estimation performance irrespective of modeling uncertainty. The proposed FIR smoothing filter is applied to the integrated navigation system composed of a magnetic compass based DR (Dead Reckoning) and a GPS (Global Positioning System) receiver. Even when the magnetic compass error that changes largely as the surrounding magnetic field is modeled as a random constant, it is shown that the FIR smoothing filter can estimate the varying magnetic compass error fast and exactly with simulation results.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.480-480
• /
• 2008

Vacuum circuit breaker(VCB) is now emerging as an alternative of gas circuit breaker(GCB) which uses SF6 gas as insulating material whose dielectric strength is outstanding. But we have to reduce SF6 gas because SF6 gas is one of greenhouse gas and efforts to reduce greenhouse gas are now trend of the world. Therefore, we can say VCB is the optimal alternative of GCB because vacuum is environmentally friendly. The vacuum interrupter is the core part of VCB to interrupt arcing current. There are mainly two methods to extinguish arc. One is radial magnetic field (RMF) method and the other is axial magnetic field (AMF) method. We deals with RMF method in this paper. Compared with AMP, RMF arc quenching method has different principle to extinguish arc. In case of RMF method, pinch effect is much larger than AMF method. Because of pinch effect RMF type contact electrodes have the single large spot which is severly damaged and melted while AMF type contact electrodes have small and multiple spots which are slightly damaged and melted. To prevent contact electrode being damaged and melted from high temperature-arc, RMF method uses Lorentz force to move arc. In this paper we calculated and compared the arc driving force of two cases and we analyzed the force acting on each part of arc by means of commercial finite element method software Maxwell 3D. They have 3petals and we considered two cases. One is the case when fixed(upper) and movable(lower) contacts are in mirror arrangement (Case 1). The other is the case when one of two contacts (movable contact) is revolved at maximum angle as possible as it can be (Case 2). And at each case above, we analyzed arc driving force at two positions, position 1 is the closest to the center of contact and position 2 is near the edge of petal on fixed contact. As a result we could find that Case 2 generated stronger arc driving force than Case 1 at position 1. But at position 2 Case 1 generated stronger arc driving force than Case 2. This simulation method can contribute to optimizing spiral-type electrode designs in a view of arc driving force.

• 전기학회논문지
• /
• 제60권3호
• /
• pp.600-605
• /
• 2011

This paper shows field test and evaluation results for a wireless vehicle detector with anisotropic magneto-resistive (AMR) sensors. The detector consists of two AMR sensors and mechanical and electronic apparatuses. The AMR sensor senses disturbance of the earth magnetic field caused by a vehicle moving over the sensor and then produces an output indicative of the moving vehicle. In this paper, vehicle speeds are calculated by using two AMR sensors fixed on a board, with constant distance. To test and evaluate the accuracy of the detector in real traffic situations, the detector was installed on a local highway and vehicle speeds and volumes were measured both in a free running and a highly congested traffic. The measurements from the detector are compared with the reference measurements obtained from a traffic camera with the Mean Absolute Percentage Errors (MAPE), which has proved the usefulness of the detector in the field.

• 센서학회지
• /
• 제10권5호
• /
• pp.292-303
• /
• 2001

본 연구에서는 수평형 전계 방출 소자를 제작하고 그 특성을 측정하였다. 이를 진공자장 센서에 이용하기 위하여 Lorentz 원리를 응용하여 센서를 설계하고 제작하였다. $POCl_3(10^{20}cm^{-3})$ 도핑된 다결정 실리콘을 전계 방출 소자의 음극 및 양극 재료로 이용하였으며 그 두께는 각각 $2\;{\mu}m$였다. PSG(두께 $2\;{\mu}m$)를 희생층으로 사용하여 최종 단계에서 불산을 이용하여 제거하고 승화건조법을 이용하여 소자의 기판 점착 현상을 방지하였다. 제작된 소자를 유리기판 #1 위에 silver paste로 고정시키고 Cr 전극 패드와 와이어본딩 한 뒤 진공내에서 양극접합공정을 이용하여 소자를 $1.0{\times}10^{-6}\;Torr$에서 진공 실장하였다. 실장 후 게터를 활성화하여 내부진공도를 향상시켰다. 이렇게 패키징된 소자는 두달여 기간 동안 특별한 특성저하 없이 잘 동작되었으며 그 이상의 기간에 대해서는 확인하지 못하였다. 패키징된 자장 센서는 패키징하기 전 진공챔버 내에서 보인 특성치와 별다른 차이 없이 잘 동작되었으며 단지 약간의 전류 감소 현상만이 관찰되었다. 측정된 센서의 감도는 약 3%/T로서 작은 값이었으나 그 가능성을 확인할 수는 있었다.

• 한국재료학회지
• /
• 제15권1호
• /
• pp.73-77
• /
• 2005

Motivated by the enhanced magnetic properties of Mg-codoped GaMnN ferromagnetic semiconductors, Be-codoped GaMnAs films were grown via molecular beam epitaxy with varying Mn flux at a fixed Be flux. The structural, electrical, and magnetic properties were investigated. GaAs:(Mn,Be) films showed metallic behavior while GaAs:Mn films showed semiconducting behavior as determined by the temperature dependent resistivity measurements. The Hall-effect measurements with varying magnetic field showed clear anomalous Hall effect up to room temperature proving ferromagnetism and magnetotransport in the GaAs:(Mn,Be) films. Planar Hall resistance measurement also confirmed the properties. The dramatic enhancement of the Curie temperature in GaMnAs system was attributed to Be codoping in the GaMnAs films as well as MnAs precipitation.

• 한국산학기술학회논문지
• /
• 제21권11호
• /
• pp.28-36
• /
• 2020

다양한 산업분야에서 자기장 센서 기술들을 응용한 제품들이 상용화되면서, 자기장 센서 데이터의 분석 및 처리방법이 중요하게 되었다. 자기장 센서는 사용하기에는 간편하고 설치에 용이하지만, 자석에 의해 생성되는 복잡한 자기력선 때문에 데이터 처리가 복잡하고, 특히 움직이는 대상에 대해서는 데이터 분석이 거의 불가능할 정도로 복잡하다. 기존의 자기장을 응용한 장비들은 자석이 움직이지 못하게 고정을 하거나, 고가의 장비들을 구입하여 데이터를 처리하는 방식을 사용하고 있다. 따라서, 자기장 센서를 사용하는 장비는 정확한 데이터를 수집하기 위해 수많은 연구가 필요하고, 고가의 장비들이 요구하게 되었다. 본 논문에서는 이런 문제점들을 해결하기 위해서, 소형의 영구 자석과 GMR 센서를 사용하여 손목 재활훈련이나 운동량을 측정하기 위해서 데이터를 처리하는 방법에 대해서 논의를 한다. 특히, 손목 재활훈련에서 발생되는 자기장 센서의 비선형적인 데이터 분석을 하고, 이런 분석을 통해서 데이터를 처리함에 있어서 고가의 장비를 사용하지 않고도 최대의 효과를 낼 수 있는 지능형 알고리즘과 같은 퍼지논리 방법을 제시하고 다른 알고리즘들과 비교하였다.

• 한국항해학회지
• /
• 제13권3호
• /
• pp.1-20
• /
• 1989

In order to provide a basic information to locate the sensor of remote-indicating magnetic compass onboard, an empirical model for the over-all ship's magnetism was developed based on the periodicity of the observed magnetic field around the vessels. The values of model parameters were determined by least-square method and optimum numbers of them were fixed using Akaike's information criterion theory, and also an approximation method to determine parameter was proposed based on the symmetrical characteristic of observed data versus ship's length. The confidence level of the newly developed models was tested by analysis of variance method. The agreement between the modelled and real values was found to be remarkably accurate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1873-1876
• /
• 2003

Magneto-rheological polishing is a new technology used in precision polishing. It utilizes magneto-rheological fluid. nonmagnetic polishing abrasive, aqueous carrier fluids in magnetic field to remove material from a part surface. Silicon micro channel as work piece is fixed in the slurry which is made of MR fluid and CeO$_2$(10 vol%) abrasive particles. And permanent magnet rotate in the slurry to transfers magnetic force to abrasive particles by increasing yield strength of MR fluid. so, the obtained bottom surface roughness of micro channel by experiment reduced to Ra 0.010 $\mu\textrm{m}$ Rmax 0.103 $\mu\textrm{m}$ and finwall surface roughness of micro channel reduced to Ra 0.018 $\mu\textrm{m}$ Rmax 0.468 $\mu\textrm{m}$. At optimum conditions of variables, the workpiece as silicon micro channel have about 24 times smaller surface roughness than before polishing.

• Journal of Magnetics
• /
• 제3권3호
• /
• pp.92-95
• /
• 1998

In this paper we report the low and high angle diffraction results, and the magnetic and magnetroesistive characteristics of the spin valve multilayer structure prepared by the sputter machine Emerald II in the Balzers Laboratory. The investigated system consists of a ferromagnetic free layer (7 nm NiFe) and a ferromagnetic pinned layer (7 nm NiFe), separated from each other by a nonmagnetic (2.1 nm Cu) spacer. The NiFe pinned layer is fixed by the exchange coupling with an antiferromagnetic layer (10 nm FeMn). For such system the magnetoresistance ratio ΔR/R=3.58%, the interlayer exchange coupling $H_c=6.4$ Oe and the field sensitivity 1.15%/Oe were otained.