• Bulletin of the Society of Naval Architects of Korea
• /
• v.10 no.1
• /
• pp.15-20
• /
• 1973

In this paper, it is desired to show a simplified analytical method in estimating the thermal stresses in the heat affected zone of butt welded joint. A finite strip as shown in Fig.1 is taken as a analytical model for stress analysis. Expressing the temperature distributions by Fourier series, the thermal stresses are obtained. From the numerical sample calculation, the following results can be obtained. (1) Thermal stresses can be estimated by the sujected method. (2) The stress component, which is parallel to the weld direction is the largest stress component in major part of the strip. (3) In obtaining a stress component for the engineering purpose, length of the strip can be treated as five times of the thickness with same degree of convergency.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.8
• /
• pp.1451-1457
• /
• 1992

In hot strip rolling, the thickness of strip cannot be retained uniform by several irregular parameters. It has been shown that the load distribution can affect only a small fraction of the excess strip crown, whereas the thermal effects of working roll are the major reason on large changes in the strip center crown during hot rolling. In this study, the temperature distribution of working roll is represented by fourier series expansion. The analytical solution of the resulting thermo-elasticity problem is obtained by love's strain function. The results which are compared with those of the finite element method show good agreements.

• Journal of Welding and Joining
• /
• v.22 no.3
• /
• pp.62-68
• /
• 2004

The strip Au bumps are bonded using longitudinal ultrasonic far the electronic package. Au bumps on the chip and substrate are aligned in a crossed shape, and the ultrasonic is imposed on the chip to form the solid-state bond between the Au bumps. Deformed bump shapes are calculated using the finite element method, and the bond strength is measured experimentally. The crossed strip Au bumps are deformed similar to the saddle, which provides larger contact surface area and higher friction force. Compared with the previous bonding method between the Au bump and planar pad, higher bond strength is obtained using the crossed strip bumps.

• Journal of Advanced Navigation Technology
• /
• v.15 no.4
• /
• pp.543-548
• /
• 2011

In this paper, H-polarized electromagnetic scattering problems by a resistive strip grating over a grounded dielectric plane according to the strip width and grating period, the relative permittivity and thickness of a dielectric layer, and incident angles of a TE (transverse electric) plane wave are analyzed by applying the FGMM (Fourier-Galerkin Moment Method). The tapered resistivity of resistive strips in this paper varies from finite resistivity at one edge to zero resistivity at the other edge, then the induced surface current density on the resistive strip is expanded in a series of Jacobi polynomials of the order ${\alpha}=1$, ${\beta}=0$ as a kind of orthogonal polynomials. The numerical results of the normalized reflected power show in good agreement with those of existing papers.

• Computers and Concrete
• /
• v.8 no.6
• /
• pp.717-733
• /
• 2011

Strengthening of reinforced concrete (RC) members against shear that is one of the failure modes especially avoided by using carbon fiber reinforced polymer (CFRP) is widely used technique, which is studied at many experimental studies. However, conducting experimental studies are required more financial resources and laboratory facilities. In addition, along with financial resources, more time is needed in order to carry out comprehensive experimental studies. For these reasons, a verified finite element model that is tested with previous experimental studies can be used for reaching generalized results and investigating parameters that are not studied. For this purpose, previous experimental study results are used and "T" cross-sectioned RC beams strengthened with CFRP strips with insufficient shear strength are modeled by using ANSYS software. First, finite elements modeling of the previously tested RC beams are done, and then the computed results are compared with the experimental ones whether they are matched or not. As a result, the finite element model is verified. Later, analyses of the cases without any test results are done by using the verified model. Optimum CFRP strip spacing is determined with this verified finite element model, and compared with the experimental findings.

• Transactions of Materials Processing
• /
• v.13 no.6 s.70
• /
• pp.497-502
• /
• 2004

The shape of cold rolled steel sheets is defined as the degree of flatness, and the flatter, the better. Because undesirable strip shapes of cold rolled steel sheets can affect not only visible problem but also automatic working process in customer's lines, the requirement of the customers is more and more stringent. So we usually used the tension leveler to make high quality of strip flatness. For the improvement of the quality of strip flatness, this report developed three- dimensional FEM (Finite Element Method) simulation model, and analysis about the strain and stress distribution of strip in the tension leveling process. The numerical study can be summarized as follows. (1) If we pass the edge wave material (steepness: $1.0\%$) that the stress-difference between the strip center and the edge is 5.2kgf through tension leveler. the stress-difference is decreased 0.45kgf and the steepness is improved to $0.29\%$. (2) If the Intermesh is increased from 6mm to 7mm, the steepness is improved from $0.294\%$ to $0.268\%$. (3) If the initial steepness is decreased form $1.0\%$ to $0.75\%$, the final steepness is improved from $0.294\%$ to $0.263\%$. We know that more increased intermesh and lower initial steepness make the final steepness improved.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.207-212
• /
• 1999

A computational method based on the three-dimensional finite element method is developed for the deformation analysis of roll forming process. the method approximates the process as a kinematically steady state deformation of strip. For industrial usefulness of the simulation method several rolls with arbitrary shapes in one stand can be considered. The shapes and the thickness distributions of strip after roll forming were examined by comparing computation results with experiments It is concluded that the tool is useful enough to predict the process. The overall simulation method was integrated into a sorftware package to help the industrial roll-design.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.03a
• /
• pp.233-237
• /
• 1995

Effects of frictional laws on finite element solutions in bulk metal forming were investigated in this paper. The Coulomb friction and the constant shear friction law were compared through finite element anlayses of compression of ring and cylinders with different aspect rations, ring-gear forging and hot strip rollin under the isothermal condition. It has been shown that two laws may yield quite different results inthe case that the aspect ration of a process is large, for example , strip rolling and ring -gear forging and that the difference depends mainly on the aspect ratio and the friction.

• Progress in Superconductivity
• /
• v.13 no.3
• /
• pp.151-157
• /
• 2012

In this paper, we used E-J constitutive law and H-formulation to calculate magnetic field profile, current density, and magnetization of high temperature superconductor (HTS) placed in time varying applied magnetic field. Finite element method (FEM)-based software, Comsol Multiphysics 3.5a, was employed to simulate 2-dimensional model of a superconducting thin strip. The numerical results based on Kim's critical state model were compared with the case of strip in a perpendicular field in the Brandt's paper as well as experimental data observed by Scanning Hall Probe and SQUID.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.121-124
• /
• 2001

On-line prediction model which calculate roll force, roll power and forward slip of continuous hot strip rolling was built based on the results of plane strait rigid-viscoplastic finite element process model. Using the integrated FE process model, a series of finite element simulation was conducted over the process variables, and the influence of various process conditions on non-dimensional parameters was inspected. The prediction accuracy of the proposed on-line model under front and back tension is examined through comparison with predictions from a finite element process model over the various process conditions. In addition, we examined the validity of the on-line prediction model through comparison with roll force of experiment in hot rolling.