• 마이크로전자및패키징학회지
• /
• 제6권4호
• /
• pp.41-48
• /
• 1999

실리카는 에폭시를 기지재로 하는 전자봉지재의 충진제로써 널리 사용되고 있는 재료이나 이의 낮은 방열성으로 인해 고방열성을 요구하는 부분에는 적용이 어렵다. 충진제 입자들의 지름비를 조합함으로써 최대충진 밀도를 높혀 고충진을 가능하게 하며 유동성도 향상된다는 점을 고려하여 높은 유동성을 가진 결정성 실리카(crystalline silica)를 큰 입자로 하고, 높은 열전도도와 낮은 열팽창계수를 가지지만 상대적으로 고각인 AlN을 작은 입자로 선정하여 혼합충진에 따른 EMC의 물성을 평가하였다. 실리카/AlN의 혼합비에 따른 EMC의 물성측정 결과, AlN의 투입분율을 0.3으로 하였을 때가 AlN의 투입에 따른 물성향상 효과가 가장 뛰어남을 확인 할 수 있었다. 따라서 AlN을 결정성 실리카와 최대 충진밀도에서 혼합하여 EMC에 적용할 경우에, 유동성의 저하없이 AlN의 소량투입만으로 뚜렷한 물성향상 효과를 얻을 수 있음을 확인할 수 있었다.

• 한국분말재료학회지
• /
• 제27권4호
• /
• pp.333-338
• /
• 2020

In this study, we fabricate a thin- and dense-BCuP-5 coating layer, one of the switching device multilayers, through a plasma spray process. In addition, the microstructure and macroscopic properties of the coating layer, such as hardness and bond strength, are investigated. Both the initial powder feedstock and plasma-sprayed BCuP-5 coating layer show the main Cu phase, Cu-Ag-Cu₃P ternary phases, and Ag phase. This means that microstructural degradation does not occur during plasma spraying. The Vickers hardness of the coating layer was measured as 117.0 HV, indicating that the fine distribution of the three phases enables the excellent mechanical properties of the plasma-sprayed BCuP-5 coating layer. The pull-off strength of the plasma-sprayed BCuP-5 coating layer is measured as 16.5 kg/㎠. Based on the above findings, the applicability of plasma spray for the fabrication process of low-cost multi-layered electronic contact materials is discussed and suggested.

• 한국세라믹학회지
• /
• 제42권6호
• /
• pp.384-390
• /
• 2005

[ ${\alpha}-Al_2O_3$ ] precursor was synthesised by sol-gel method using aluminum sulfate, sodium sulfate and sodium carbonate as law materials. The flaky ${\alpha}-Al_2O_3$ crystals were prepared by heating using precursor about $1,050^{\circ}C$. In this study, the effect of some transition-metal sulfate ($FeSO_4,\;SnSO_4,\;ZnSO_4$) addition have been investigated. When iron sulfate was added, it could see that act on impurities in crystal growth process. In case of tin sulfate, distribution of Platelets was very broad. When flaky ${\alpha}-Al_2O_3$ crystals were prepared zinc sulfate addition, thickness, size, and distribution of platelets was suited to industrial application. The average diameter of flaky ${\alpha}-Al_2O_3$ crystals was about 20 $\mu$m, and its thickness was about 0.3 $\mu$m. Increasing addition of zinc sulfate, thickness of ${\alpha}-Al_2O_3$ platelet was decreased.

• 펄프종이기술
• /
• 제40권2호
• /
• pp.8-15
• /
• 2008

Wastewoods (logging residues) generated in Korea were used to make lignocellulosic fillers for papermaking. Lignocellulosic fillers could play great roles to increase retention efficiency and thus decrease turbidity of white water in papermaking process. In addition, lignocellulosic fillers could be used to improve physical properties of paper through their high affinity to cellulosic fibers, leading to the less use of chemical additives like retention aids. Wastewoods including Pinus densiflora and Quercus variabilis were chemically and mechanically treated for making fine particles passing through 100 mesh wire. The newly generated fillers showed larger particle size distribution than ground calcium carbonates but similar distribution to talc. In particular, pretreatment by hot water was more effective to generate smaller particle size than by alkali treatment. Lignocellulosic particles mixed with ground calcium carbonates under intense hybridizing condition greatly contributed to surface coverage of organic fillers in addition to filling to lumen and pits.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.1169-1170
• /
• 2006

Grid connected PV(Photovoltic) generation systems are becoming and actual and general. The power output of PV system is directly affected by the weather conditions. And when AC power supply is needed, power conversion by an inverter and a MPPT control are necessary. The PV power generation system can be treated to a harmonics source for the power distribution system. So, the PV system combined the function of active filter system can be useful applied in power distribution system. AF(Active Filters) intended for harmonic solutions are expending their functions from harmonic compensation of nonlinear loads into harmonic isolation between utilities and consumer. With the test analysis of the proposed control strategy of PV-AF system, the outcome of the test shows the stability and effectiveness of the proposed PV-AF system. The various capability of AF has been proved in previous research and usage. In this paper, authors present a DSP controlled PV-AF system for power conditioning in three-phase industrial or commercial power systems and verify it through experimental results.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 추계학술대회 논문집
• /
• pp.175-178
• /
• 1995

Distribution of relaxation time is presented in the Cole-Cole arc diagram with frequency parameter. In the case of estimation of activation energy for main chains, maximum loss frequencies of ${\alpha}$ peaks, f$\sub$m/(${\alpha}$) display curved change according to the WLF type with variations of temperature. Structural change by the filling of filler and degradation by the thermal aging can be estimated from the WLF factors, C$_1$and C$_2$in Log f$\sub$m/-1/T curves which reflect the variations of free volume and thermal expansivity of composites.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2007년도 추계학술발표논문집
• /
• pp.127-134
• /
• 2007

Paper is composed network of fibers. Since paper is plain, most cases paper is considered two-dimensional. But network of fibers creates a network of pores, and pores between fibers are most important part of the paper structure. So we have to make an approach to the paper by three-dimensionally. Pore structure in the Z-direction of the paper can affect directly not only basic properties od the paper such as density, porosity, opacity and strength but also coverage of the coating colors during coatong and printing properties. We studied effect of raw materials of the papermaking and physical treatment on the pore structure and properties of the paper.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1597-1599
• /
• 1996

In this study, we investigated the electrical characteristics such as tracking resistance, dielectric constant, insulating resistance, and arc resistance, of silicone rubber for outdoor use, and, focused on the tracking resistance. In the Inclined Plane Test, two kind of the contamination solutions were used, and their phenomena were observed. The average leakage current and the tracking breakdown time decreased, and erosion rate increased, using anionic surfactant added contaminant solution. The dielectric constant and dissipation factor were increased with increasing temperature.

• 한국응용과학기술학회지
• /
• 제32권1호
• /
• pp.40-47
• /
• 2015

Single-walled carbon nanotubes (SWNTs) was modified with various length of linear alkyl chains and passivated to form dielectric filler. The modified SWNTs embedded into epoxy matrix to fabricate a flexible composite with high dielectric constant. The dielectric behavior of the composite was significantly changed with various alkyl chain length(n) of pyrene. The dielectric constant of the epoxy/SWNTs composite significantly increased with respect to increase in length of alkyl chain at the frequency range from 10 to 105Hz (n=12and18).We also found that the passivated epoxy/SWNTs composite with high dielectric constant presented low dielectric loss. The resulted dielectric performances corresponded to de-bundling of nanotubes and their distribution behavior in the matrix in terms of tail length of alkyl pyrene in the passivation layer.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1994년도 추계학술대회 논문집
• /
• pp.206-209
• /
• 1994

This paper has been researched bondability of electronic devices, such as lead frame and thick film of Ag/Pd on an alumina substrate by different heat sources. To obtain the bonds with high quality, it is very important to control both the thermal distribution of the bonds and it stability, because electronics components is consist of different materials. Therefore, this paper clarifies not only heat mechanism of micro parallel gap resistance bonding method and pulse heat tip bonding method but also investigates selection of heat sources with micro-electronic materials for bonding. Finally, it is realzed fluxless bonding process with filler metal such as plating layers.