• Journal of Power System Engineering
• /
• v.9 no.2
• /
• pp.93-98
• /
• 2005

The performance of cooling tower is dependent on the thermal performance of the packings. It's assessed by heat transfer rate and fan power. In this study, new packing was developed for application in compact type cross-flow cooling tower. The packing characteristic curve and the pressure drop curve were obtained by measuring packing characteristic values and pressure drops of small sized filler in comparison to existing mid-large sized filler. The heat transfer characteristics on small sized filler are about 66% higher than existing mid-large sized filler. The pressure drop characteristics on small sized filler are about two times of the pressure drop characteristics on existing mid-large sized filler.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.98-103
• /
• 2001

In case that electronic ballast employing a valley-fill passive power factor correction (PFC) circuit is used for feeding fluorescent lamps, a new method to reduce crest factor of the lamp current is studied in this paper. In order to reduce crest factor to lower value, a pulse frequency modulation technique based on the waveform of the dc-link voltage which is predetermined by the passive PFC circuit, is taken into the switching control action of the electronic ballast. An equation-based analysis between the crest factor of lamp current and the effect of varying the inverter switching frequency is comprehensively performed.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2795-2797
• /
• 1999

Several power factor correction(PFC) circuits are presented to achieve high PF electronic ballast for both voltage-fed and current-fed electronic ballast. The proposed PFC circuits use valley-fill(VF) type DC-link stages modified from the conventional VF circuit to adopt the charge pumping method for PFC operations during the valley intervals. In voltage-fed ballast, charge pump capacitors are connected with the resonant capacitors. In current-fed type, the charge pump capacitors are connected with the additional secondary-side of the power transformer. The measured PF and THD are higher than 0.99 and 15% for all proposed PFC circuits. The lamp current CF is also acceptable in the proposed circuits. The proposed circuit is suitable for implementing cost-effective electronic ballast.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.2
• /
• pp.189-196
• /
• 1994

This paper describes a parallel computing algorithm in Gauss elimination of Jacobian matrix to large-scale power system. The structure of Jacobian matrix becomes different according to ordering method of buses. In sequential computation buses are ordered to minimize the number of fill-in in the triangulation of the Jacobian matrix. The proposed method develops the parallelism in the Gauss elimination by using ND(nested dissection) ordering. In this procedure the level structure of the power system network is transformed to be long and narrow by using end buses which results in balance of computing load among processes and maximization of parallel computation. Each processor uses the sequential computation method to preserve the sqarsity of matrix.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.227-228
• /
• 2012

In interfaces between carbon black or Pt and FTO glass in dye-sensitized solar cell counter electrodes, a marginal resistant channel for electrons, we tried to improve the connection by modifying the sintering process. A stepwise sintering process for carbon black and Pt counter electrodes was applied and its effect on power conversion efficiency was studied. Power conversion efficiencies of built-in DSSC made by a one-step sintering process with carbon black and Pt counter electrodes were about 5.01% and 5.02%, respectively. Cells made with the stepwise sintering process were 5.96% and 6.21%, respectively, indicating an 20% improvement. Fill factor (FF) increased, and it was them main reason for the power conversion efficiency improvement. Step wise sintering increased the adhesion of the interface and reduced the film thickness and surface roughness. As a result, the resistivity of the counter electrode and EIS impedance of DSSCs decreased.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.95-96
• /
• 2014

450mm 반도체 CVD 장비 개발 및 300mm F-CVD (Flowable CVD) 공정 개발에 있어서 공정 마진 확보 및 막질 품질 개선을 위해 주파수 가변형 RF Generator가 필수적으로 요구되고 있다. 20nm이하 STI (Shallow Trench Isolation), PMD (Pre-metal Dielectric) & IMD (Inter-Metal Dielectric) 미세공정 gap fill에 많은 문제점이 도출되고 있으며, 이유로는 Generator 고정 주파수에서 Matching Time delay 또는 Shooting에 의한 산포의 한계로 파악되었으며, 주파수 가변에 의한 고속 Tune 기능이 요구되어진다. 따라서 400kHz 주파수 가변형 RF-Generator 개발을 진행하였으며 본 논문을 통해 개발되어진 장비의 성능과 시험 평가한 결과를 소개하고자 한다.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.2
• /
• pp.41-50
• /
• 2000

본 연구에서는 여러 침하모델들을 매립경과기간이 다른 아홉 개 지역의 실제 스레기 매립지 침하자료들에 적용하였다. 침하모델들을 적용한 결과, 매립연한이 증가할수록 향후 발생가능한 장기침하량도 상당히 감소하는 경향을 보였다. 신선한 쓰레기 매립지에서는 침하모델들마다 예측정도에서 큰 차이를 보이지만, 매립연한이 오래된 매립지들에서는 Power creep law를 제외하고는 예측정도에 있어서 큰 차이를 보이지 않음을 알 수 있었다.

• Geotechnical Engineering
• /
• v.12 no.6
• /
• pp.65-78
• /
• 1996

The Chungpyung Dam is a 16 yearn old rock-fill dam for a Pumped storage hydro-Power plant, located in the middle of the Korean Peninsula. Since the dam is subjected to the daily water level fluctuation, such as rapid drawdown and refill, thus inducing a structural impact on the behavior of dam body, it draws attention of many engineering concerns. Traditionally, steady-state analysis was employed to investigate the seepage in the dam body, but in this study the seepage analysis was numerically performed by 2-D FEM thansient analysis. As a boundary condition for an analysis, the water level fluctuation was incorporated to simulate the daily change. As a res41t, the various seepage phenomena such as hydraulic gradient, seepage vector, and pore water pressure distribution were quantified at the corresponding time of interest as the water level rises and recedes. The seepage flux was also estimated and compared with the measured data which were both acceptable considering design criteria. The result proves that there is no sign of hazardous sources contributing to the possibility of piping, internal erosion and excess leakage through the dam body.

• Journal of Welding and Joining
• /
• v.16 no.5
• /
• pp.119-133
• /
• 1998

To implement full automation in pipe welding, it si most important to develop special sensors and their related systems which act like human operator when detecting irregular groove conditions. In this study, an automatic pipe Gas Metal Arc Welding (GMAW) system was proposed to full control pipe welding procedure with intelligent sensor systems. A five-axes manipulator was proposed for welding torch to automatically access to exact welding position when pipe size and welding angle were given. Pool status and torch position were measured by using a weld-pool image monitoring and processing technique in root-pass welding for weld seam tracking and weld pool control. To overcome the intensive arc light, pool image was captured at the instance of short circuit of welding power loop. Captured image was processed to determine weld pool shape. For weld seam tracking, the relative distance of a torch position from the pool center was calculated in the extracted pool shape to move torch just onto the groove center. To control penetration of root pas, gap was calculated in the extracted pool image, and then weld conditions were controlled for obtaining appropriate penetration. welding speed was determined with a fuzzy logic, and welding current and voltage were determined from a data base to correspond to the gap. For automatic fill-pass welding, the function of human operator of real time weld seam control can be substituted by a sensor system. In this study, an arc sensor system was proposed based on a fuzzy control logic. Using the proposed automatic system, root-pass welding of pipe which had gap variation was assured to be appropriately controlled in welding conditions and in torch position by showing sound welding result and good seam tracking capability. Fill-pass welding by the proposed system also showed very successful result by tracking along the offset welding line without any control of human operator.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.177-181
• /
• 2012

본 연구는 고온고습 시험을 통하여 Cell 레벨에서의 표면관찰 및 효율저하를 분석하였다. 고온고습 시험 조건은 KS C IEC-61215에서 제시한 PV module하의 조건을 이용하여 온도 $85^{\circ}C$, 습도 85% 조건하에 1000시간 동안 수행하였다. 고온고습 시험에 따라 효율에 직접적인 영향을 줄 수 있는 이상 유 무를 Cell 표면을 통해 분석한 결과, 고온고습 시험 수행 중 부분적으로 변색되는 것을 확인하였다. 고온고습 시험 전 단결정 Cell의 효율은 17.74% 였으며, 1000시간 수행 후 15.63%으로 11.89%의 감소율을 보였다. 다결정 Cell의 시험 전 효율은 15.46%, 1000시간 수행 후 효율은 14.02%로 9.31%의 감소율을 보였다. 경년 시 나타나는 전기적 특성을 분석하기 위해 FF(Fill Factor)값을 분석한 결과, 고온고습 시험 전 단결정 Cell은 78.71%에서 75.01%로 4.7%의 감소율을 보였으며, 다결정 Cell은 78.10 %에서 76.66%로 1.84%의 감소율을 보였다. 효율 및 FF값에서 단결정 Cell이 다결정 Cell보다 감소율이 큰 것으로 분석되었으며, 이는 단결정 Cell이 외부 환경에서 더욱 크게 작용하여 효율저하에 영향을 주었다고 판단된다.