• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.6
• /
• pp.1596-1603
• /
• 1996

A single body type of fiber-optic current and voltae sensor using a rare earth doped YIG and a bismuth silicon oxide single crystsl is proposed, which is used for simultaneous measurement of the AC electric current and AC electric voltage over the trasmission lines. Experimental results showed that the fiber-optic current sensor has the maximum 7.5% error within the current range of 0A to 400A, and the fiber-optic voltage sensor has the maximum 0.87% error within the current range of 0V to 400V. The output waveforms of proposed fiber-optic sensor system has a good agreement with output waveforms of conductor current and voltage. Experimental results proved that the output of fiber-optic current sensor is not affected by the electric voltage applied to the fiber-optic voltage sensor, and also, that the output of fiber-optic voltage sensor is not affected by the electric current applied to the fiber-optic current sensor.

• Korean Journal of Optics and Photonics
• /
• v.29 no.5
• /
• pp.187-203
• /
• 2018

This paper reviews the progress achieved in the field of fiber-optic communications during the last 40 years, and discusses its future directions. In particular, the highlights and milestones in the development of the high-capacity fiber-optic transmission system are presented in historical perspective.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.8 no.4
• /
• pp.139-144
• /
• 1983

In this paper, the ploarization and Faraday rotation properties of the single mode optical fiber have been investigated for magnto-optic current transformer application. On the analysis, the optical fiber is modeled as a linear retarder and the intrinsic birefreingence of the optical fiber is approximately found to be 2.57'/m from the measurement, and the bend-induced birefringence is proportional to the inverse square of bending radius. The polarization rotation sensitivity is foung to be F/H=1.4x$10^-5$rad/[A/m] from the analysis of Faraday rotation of single mode optical fiber.

• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2495-2497
• /
• 1998

Fiber optic facilities are increasingly being deployed in loop applications for both busines and residential areas. These facilities support a variety of communications services that include high speed data and video using leading technologies such as Synchronous Optical Network (SONET), Wavelength Division Multiplexing(WDM). This proliferation of fiber optic facilities combined with the increasing pressure on network operators to reduce costs are fostering increased automation to reduce labor costs associated with providing and maintaining communications services. Effective fiber management and accurate records can improve the reliability and integrity of the future telecommunications networks and the quality of customer services. This paper describes the trend forward and the need for the deployment of Fiber Administration System (FAS) into the operations enviroment of a typical network provider.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.10B
• /
• pp.1707-1713
• /
• 2000

We have proposed a tunable optical ADM using a fiber-optic transversal filter which is composed of fiber couplers and metal-film coated fiber-optic tapped delay-lines with a flat spectral response in abroad range of wavelength. Simulation results show that the optical loss at the DROP and PASS wavelengths of the OADM is negligible and the wavelength tunability is 0.78${\mu}{\textrm}{m}$/ps for the unit time delay of 2 ps. In order to investigate the effects of wavelength drift of the imput optical signal on the OADM the loss at the DROP port and the crosstalks to the other ports have been calculated. The maximum bit rates have been calculated at 46.26 Gb/s for the input Gaussian pulse width of 10 ps.

• ETRI Journal
• /
• v.30 no.2
• /
• pp.275-281
• /
• 2008

A 40 Gb/s clock and data recovery (CDR) module for a fiber-optic receiver with improved phase-locked loop (PLL) circuits has been successfully implemented. The PLL of the CDR module employs an improved D-type flip-flop frequency acquisition circuit, which helps to stabilize the CDR performance, to obtain faster frequency acquisition, and to reduce the time of recovering the lock state in the event of losing the lock state. The measured RMS jitter of the clock signal recovered from 40 Gb/s pseudo-random binary sequence ($2^{31}-1$) data by the improved PLL clock recovery module is 210 fs. The CDR module also integrates a 40 Gb/s D-FF decision circuit, demonstrating that it can produce clean retimed data using the recovered clock.

• Journal of Communications and Networks
• /
• v.12 no.3
• /
• pp.246-252
• /
• 2010

A binary linear integer program is formulated for the problem of expanding the capacity of a fiber optic network and routing the traffic to deliver new interactive multimedia services. A two-phase Lagrangian dual search procedure and a Lagrangian heuristic are developed. Computational results show superior performance of the two-phase subgradient optimization compared with the conventional one-phase approach.

• Journal of IKEEE
• /
• v.13 no.4
• /
• pp.103-109
• /
• 2009

We report an efficient jitter reduction technique in an analog fier-optic link employing a Mach-Zehnder modulator followed by an erbium-doped fiber amplifier. By adjusting the modulator-bias to $0.089V_{\pi}$, we could increase the RF gain up to 10.65 dB for 10 GHz RF signal and reduce the random jitter by 46.5%, max, at an input optical power of -0.11 dBm to the EDFA.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.10A
• /
• pp.1200-1204
• /
• 2004

Fiber-optic sensor (FOS) using bending-sensitive fiber (BSF which detects physical variables according to the variation of fiber-bending is proposed. BSF is already used in variable optical attenuator. Three-dimensional finite difference beam propagation method (3D FD-BPM) is used to investigate the bending loss of BSF. Then, the results of bending experiment with FOS consisting of BSF is compared to numerical results of 3D FD-BPM. In particular, the optical power of fabricated FOS with BSF varies from -ldB to -2OdB when pressure given to the upper side of FOS changes from 0 MPa to 0.005 MPa, while the FOS consists of SMF shows no change of optical power at the same condition.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.02a
• /
• pp.72-73
• /
• 2000

Optical fiber gratings have been intensively studied for applications in optical fiber communications and sensor systems due to their all-fiber configuration, low insertion loss, low cost, and high flexibility. Especially, cladding mode coupling fiber devices such as long period gratings (LPG) and acousto-optic tunable filters (AOTF) have been developed as a gain equalization filter in erbium doped fiber amplifier (EDFA) for wavelength division multiplexing (WDM) systems$^{(1-2)}$ . (omitted)