• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.1
• /
• pp.161-166
• /
• 2016

We studied the effect of $Co^{60}$ gamma-radiation on the FBGs by a variation of grating the fabrication parameters. The FBGs were fabricated in a different UV KrF laser intensity using the same boron co-doped photo-sensitive fiber and exposed to gamma-radiation up to a dose of 33.8 kGy. According to the experimental data and analysis results, We confirmed that the laser intensity for grating inscription has a highly effect on the radiation sensitivity of the FBGs and the radiation-induced Bragg wavelength shift by the change of laser process condition showed a difference more than about 30 %.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.10
• /
• pp.256-263
• /
• 2014

We have designed and made three kinds of FBG(Fiber Bragg Grating) Acoustic Transducer using Hopper type WDM on the use of recently developed FBG in Korea. The newly designed three kinds of FBG Acoustic Transducer using Hopper type WDM have an excellent merit of practical use with simple structure of sensors arm as well as the merit with existing fiber sensors. It was possible to detect sound waves in the range of 10 Hz to 18 kHz through the newly designed three kinds of FBG Acoustic Transducer and also, possible to detect its signal within the maximum range of 8.6 m by the use of most suitable resonance condition of the transducer. Especially, we can expect the utilization of low-frequency signal detection instead of existing acoustic sensor in the environment of electric noise and inferior condition. Furthermore, they can be developed as the high-sensibility and multi-point signal detection system through the sensor array system.

• Korean Journal of Optics and Photonics
• /
• v.26 no.6
• /
• pp.306-311
• /
• 2015

We report the characteristics of a single-wavelength-tunable fiber laser using a polymer waveguide Bragg grating (PWBG) wavelength filter. The output of the laser depends on environmental conditions, such as temperature and polarization states in the laser cavity. Wavelength tuning can be achieved, about 16.29 nm from 1548.24 nm to 1531.95 nm, according to the electric power applied to the PWBG wavelength filter. The achieved efficiency slope is about -0.16 nm/mW. A side-mode suppression ratio (SMSR) of more than 35 dB can be obtained by adjusting the polarization state in the laser cavity. A stable wavelength-tunable fiber laser can be achieved using the PWBG wavelength filter with a TEC module and a polarization-maintaining fiber.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4A
• /
• pp.639-645
• /
• 2006

FRP (Fiber Reinforced Polymer) is an excellent new constructional material in resistibility to corrosion, high intensity, resistibility to fatigue, and plasticity. FBG (Fiber Bragg Grating) sensor is widely used at present as a smart sensor due to lots of advantages such as electric resistance, small-sized material, and high durability. However, with insufficiency of measuring displacement, FBG sensor is used only as a sensor measuring physical properties like strain or temperature. In this study, FRP and FBG sensors are to be hybridized, which could lead to the development of a smart FRP rod. Moreover, developing the estimated model for deflection with neural network method, with the data measured through FBG sensor, could make conquest of a disadvantage of FBG sensor - uniquely used for sensing strain. Artificial neural network is MLP (Multi-layer perceptron), trained within error rate of 0.001. Nonlinear object function and back-propagation algorithm is applied to training and this model is verified with the measured axial displacement through UTM and the estimated numerical values.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.1 s.94
• /
• pp.3-11
• /
• 2005

For monitoring of the civil and building structure, optical fiber sensors are very convenient. The fiber sensors are very small and do not disturb the structural properties. They also have several merits such as electro-magnetic immunity, long signal transmission, good accuracy and multiplexibility in one sensor line. Strain measurement technologies with fiber optic sensors have been investigated as a part of smart structure. In this paper, we investigated the possibilities of fiber optic sensor application to the monitoring of beam-column joints of structures. We expect that the fiber optic sensors replace electrical strain gauges. The commercial electric strain gauges show good stability and dominate the strain measurement market. However, they lack durability and long term stability for continuous monitoring of the structures. In order to apply the strain gauges, we only have to attach them to the surfaces of the structures. In this paper, we investigate the possibility of using fiber optic Bragg grating sensors to joint structure. The sensors show nice response to the structural behavior of the joint.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.595-601
• /
• 2003

For monitoring of the civil and building structure, optical fiber sensors are very convenient. The fiber sensors are very small and do not disturb the structural properties. They also have several merits such as electro-magnetic immunity, long signal transmission, good accuracy and multiplicity of one sensor line. Strain measurement technologies with fiber optic sensors have been investigated as a part of smart structure. In this paper, we investigated the possibilities of fiber optic sensor application to the monitoring of beam-column joints of structures. We expect that the fiber optic sensors replace electrical strain gauges. The commercial electric strain gauges show good stability und dominate tile strain measurement market. However, they lack durability and long term stability for continuous monitoring of the structures. In order to apply the strain gauges, we only have to attach them to the surfaces of the structures. In this paper, we investigate the possibility of using fiber optic Bragg grating sensors to joint structure. The sensors show nice response to the structural behavior of the joint.

• Journal of the Optical Society of Korea
• /
• v.7 no.2
• /
• pp.53-58
• /
• 2003

We report the formation of inner cladding modes in the optical fiber having an inner cladding structure. The inner cladding layer located between the core- and the cladding- layers of a conventional fiber might have, so called, inner cladding mode(s). The brief history of the inner cladding fiber and the spectral properties of the inner cladding mode are presented. By utilizing fiber gratings, the spectral properties of the inner cladding mode formed in Dispersion Compensating Fiber (DCF) are discussed. It was observed that one resonant peak of a long-period fiber grating was not sensitive to the variation on the cladding surface. With a fiber Bragg grating, a small group of unusual resonant Peaks was observed between the main Bragg Peak and the series of usual Peaks resulted from the mode coupling to counter-propagating cladding modes. Within the DCF by using fiber gratings, it is noted, at least one mode can be coupled to the inner cladding mode and a few outer cladding modes are severely affected by the inner cladding of the fiber.

• Korean Journal of Optics and Photonics
• /
• v.21 no.5
• /
• pp.190-194
• /
• 2010

A hybrid grating sensing device based on a side-polished fiber Bragg grating (FBG) with a polymer overlay is proposed for simultaneous measurement of external refractive index and temperature. The side-polished FBG, which is insensitive to ambient index change, is utilized for detecting temperature variation, and the polymer overlay is coated on the side-polished FBG for measurement of ambient index change. The temperature sensitivities of the side-polished FBG and the polymer overlay were measured to be 0.01 nm/$^{\circ}C$ and -0.58 nm/$^{\circ}C$, respectively, in a temperature range from $30^{\circ}C$ to $100^{\circ}C$. The ambient index sensitivities of the polymer overlay were measured to be 498.8 nm/RIU in an ambient index range from 1.33 to 1.39, 694.9 nm/RIU from 1.39 to 1.42, and 1312 nm/RIU from 1.42 to 1.44.

• Composites Research
• /
• v.18 no.1
• /
• pp.16-22
• /
• 2005

Application fields on structural health monitoring of fiber Bragg gratings (FBGs) are gradually expanded even to a primary structure as well as a secondary structure and a specimen. For the reason, verification for the reliability of FBGs such as signal characteristics and mechanical strength becomes much more important. In this study, mechanical strength characteristics of FBGs with their fabrication process and reflectivity are investigated with various grating lengths. From the results of tension tests, it is shown that the mechanical strength of optical fibers decreases about $50\%$ just by jacket stripping and the amount of decrease is dependent on stripping methods. About $55\%$ of mechanical strength of stripped optical fibers decreases if gratings are formed in the core and it is regardless of grating lengths and reflectivity. However, the width of strength distribution increases relative to increases in reflectivity.

• Journal of Sensor Science and Technology
• /
• v.22 no.2
• /
• pp.95-99
• /
• 2013

We proposed and demonstrated a fiber optic sensor for detecting the thermo-optic coefficient of a liquid, based on a cascade of two different FBGs. One of the two FBGs was etched, and its cladding was removed, for evanescent wave coupling with an external liquid. The Bragg wavelength of the non-etched FBG was used as a reference for the temperature of the surrounding liquid. The refractive index (RI) and thermo-optic (T-O) coefficient of a liquid can be detected from the difference between the Bragg wavelengths of the two FBGs, and the variation of the difference in accordance with temperature.