• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.10
• /
• pp.87-95
• /
• 2014

This paper describes a dual channel receiver design for CIS interfaces. Each channel includes CTLE(Continuous Time Linear Equalizer), sampler, deserializer and clocking circuit. The clocking circuit is composed of PLL, PI and CDR. Fast lock acquisition time, short latency and better jitter tolerance are achieved by adding OSPD(Over Sampling Phase Detector) and FSM(Finite State Machine) to PI-based CDR. The CTLE removes ISI caused by channel with -6 dB attenuation and the lock acquisition time of the CDR is below 1 baud period in frequency offset under 8000ppm. The voltage margin is 368 mV and the timing margin is 0.93 UI in eye diagram using 65 nm CMOS technology.

• Journal of the Korean Chemical Society
• /
• v.35 no.6
• /
• pp.713-719
• /
• 1991

Electrochemical impedance measurement system using Fourier transform was constructed in the range of the frequencies up to 100 kHz. This system consists of pseudo-random noise generator, specially designed potentiostat, fast data acquisition system, system controller, and computer interface. The performance of the constructed system was found to be almost same as the commercially available system using lock-in amplifier. Measuring time was significantly reduced because the minimum time for the measurement depended on one cycle of the lowest frequency used. It would be possible to study time-varying electrochemical impedance systems such as the initial stages of corrosion processes using this system.

• Aerospace Engineering and Technology
• /
• v.10 no.1
• /
• pp.45-53
• /
• 2011

This paper is technical review about Direct Sequence Spread Spectrum(DSSS) to apply in launch vehicle system. First, we introduce communication protocol(carrier frequency, code length, process gain, data rate, chip rate etc) about several application system using DSSS. And then, we survey and summarize the effect of doppler shift to the DSSS. The doppler shift is important error factor for PN code tracking in the fast moving system like launch vehicle. So, spread spectrum code acquisition technique for a direct sequence system in the presence of doppler effect must be investigated.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.605-608
• /
• 2009

It is necessary to estimate the Doppler spectrum for each range cell for the extraction of useful information from the return echoes in radar systems used for the remote sending purpose. However, The conventional spectrum estimation method, FFT(Fast Fourier Transform), called the Doppler filter bank, causes the frequency resolution problem if the dwell time is relatively short. This short acquisition time also spreads the side lobe levels of return echoes further, resulting in difficulties for the discrimination of weak target signals included in relatively strong target echoes. Therefore, in this paper, the efficient Doppler spectrum estimation methods are compared and investigated through the parameter spectrum estimation in the time domain to overcome these problems.

• Current Optics and Photonics
• /
• v.8 no.2
• /
• pp.127-137
• /
• 2024

The distribution of tags is an important factor that affects the performance of radio-frequency identification (RFID). To study RFID performance, it is necessary to obtain RFID tags' coordinates. However, the positioning method of RFID technology has large errors, and is easily affected by the environment. Therefore, a new method using optical measurement is proposed to achieve RFID performance analysis. First, due to the possibility of blurring during image acquisition, the paper derives a new image prior to removing blurring. A nonlocal means-based method for image deconvolution is proposed. Experimental results show that the PSNR and SSIM indicators of our algorithm are better than those of a learning deep convolutional neural network and fast total variation. Second, an RFID dynamic testing system based on photoelectric sensing technology is designed. The reading distance of RFID and the three-dimensional coordinates of the tags are obtained. Finally, deep learning is used to model the RFID reading distance and tag distribution. The error is 3.02%, which is better than other algorithms such as a particle-swarm optimization back-propagation neural network, an extreme learning machine, and a deep neural network. The paper proposes the use of optical methods to measure and collect RFID data, and to analyze and predict RFID performance. This provides a new method for testing RFID performance.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.599-603
• /
• 2003

This paper present an error compensation system and On-Machine Measurement(OMM) system for improving the machining accuracy of ultra-precision lathe. The Fast-Tool-Servo(FTS) driven by a piezoelectric actuator is applied for error compensation system. The controller is implemented on the 32bit DSP for feedback control of piezoelectric actuator. The control system is designed to compensates three kinds of machining errors such as the straightness error of X-axis slide, the thermal growth error of the spindle. and the squareness between spindle and X-axis slide. OMM is preposed to measure the finished profile of workpiece on the machine-tool using capacitive sensor with highly accurate ruby tip probe guided by air bearing. The data acquisition system is linked to the CNC controller to get the position of each axis in real-time. Through the experiments, it is founded that the thermal growth of spindle and tile squareness error between spindle and X-axis slide influenced to machining error more than straightness error of X-axis slide in small travel length. These errors were simulated as a sinusoidal signal which has very low frequency and the FTS could compensate the signal less than 30 m. The implemented OMM system has been tested by measuring flat surface of 50 mm diameter and shows measurement error less than 400 mm

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.8
• /
• pp.3925-3932
• /
• 2013

Emotion is closely related to the life of human, so has effect on many parts such as concentration, learning ability, etc. and makes to have different behavior patterns. The purpose of this paper is to extract important features based on physiological signals to recognize negative emotion. In this paper, after acquisition of electrocardiography(ECG), electroencephalography(EEG), skin temperature(SKT) and galvanic skin response(GSR) measurements based on physiological signals, we designed an accurate and fast algorithm using combination of linear discriminant analysis(LDA) and genetic algorithm(GA), then we selected important features. As a result, the accuracy of the algorithm is up to 96.4% and selected features are Mean, root mean square successive difference(RMSSD), NN intervals differing more than 50ms(NN50) of heart rate variability(HRV), ${\sigma}$ and ${\alpha}$ frequency power of EEG from frontal region, ${\alpha}$, ${\beta}$, and ${\gamma}$ frequency power of EEG from central region, and mean and standard deviation of SKT. Therefore, the features play an important role to recognize negative emotion.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.5
• /
• pp.341-349
• /
• 2003

A real time interactive controller (spectrometer) for magnetic resonance imaging (MRI) system has been developed using high speed digital signal processors (DSP). The controller generates radio frequency (rf) waveforms and audio frequency gradient waveforms and controls multiple receivers for data acquisition. By employing DSPs having high computational power (e.g., TMS320C670l) real time generation of complicated gradient waveforms and interactive control of selection planes are possible, which are important features in real-time imaging of moving organs, e.g., cardiac imaging. The spectrometer was successfully implemented at a 1.5 Tesla whole body MRI system for clinical application. Performance of the spectrometer is verified by various experiments including high- speed imaging such as fast spin echo (FSE) and echo planar imaging (EPI). These high-speed imaging techniques reduce measurement time, however, usually intensify artifact if there is any systematic phase error or jitter in the synchronization between the transmitter, receiver, and gradients.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.3
• /
• pp.317-323
• /
• 1998

A synchronization is important element not only wire communication but also wireless communication. Especially, In SS(Spread Spectrum) communication method used GPS(Global Positioning System) synchronization is more important. A synchronous oscillator(SO) is a network which synchronizes, tracks, filter, amplifies and divides (if necessary) in a single process. Without an input signal, the SO is a free-running oscillator, oscillating at a frequency $w_0$, but phase changes $180^{\circ}$ within tracking range of SO. Therefore CPSO was used for this problem. The coherent phase synchronous oscillator(CPSO) is created by adding two external loops to the SO and has a wider tracking bandwidth and a zero-offset phase response (coherent) while maintaining the SO properties of high signal-to-rejection and fast frequency acquisition times. Therefore phase between input signal and output signal is synchronized. In this paper, GPS data recovery circuit has applied CPSO using front reference characters and has certified an excellent data recovery capability.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.7
• /
• pp.1575-1581
• /
• 2003

As a society has progressed rapidly toward a highly advanced digital information age, a multimedia communication service for acquisition, transmission and storage of image data as well as voice has being commercialized externally and internally. However, in the process of digitalization or transmission of data, noise is generated by several causes, and researches for eliminating those noises have been continued until now. There were the existing FFT(fast fourier transform) and STFT(short time fourier transform) for removing noise but it's impossible to know information about time and time-frequency localization capabilities has conflictive relationship. Therefore, for overcoming these limits, wavelet transform which is presented as a new technique of signal processing field is being applied in many fields recently. Because it has time-frequency localization capabilities it's Possible for multiresolution analysis as well as easy to analyze various signal. And when two wavelet base were designed to form Hilbert transform pair, wavelet pair provide superior performance than the existing DWT(discrete wavelet transform) in data characteristic detection. Therefore in this parer, we removed impulse noise by using adaptive-length median filter and two dyadic wavelet base which is designed by truncated coefficient vector.