• Journal of Korean Society for Quality Management
• /
• v.24 no.2
• /
• pp.65-76
• /
• 1996

In general, most industrial products exhibit bath-tub shaped curve for their failure rate functions. This distributional life model can be obtained by the Piecewise Weibull distribution. The least squares, maximum likelihood, and mixed methods of estimating the parameters of the Piecewise Weibull distribution are compared. The comparison is made by using the empirical mean squared errors of (a) the parameter estimates and (b) the estimated change-points, to summarize the results of 1000 simulated samples of three sizes - each 100, 150 and 200. The results are that the mixed method estimation comes to be the best as the sample sizes increase.

• Tunnel and Underground Space
• /
• v.6 no.3
• /
• pp.260-266
• /
• 1996

Safety concern is one of the most important parameters in the design of explosive building demolition. Laboratory experiments were performed to investigate the failure behaviour of concrete columns and the effects of protection materials. Fourteen reinforced columns with two sizes were constructed and the effects of protection materials were tested for two kinds of materials: non woven fabrics and wire net. The results showed that control of gas effects is a key to the control of flying chips. It was recommended to use both wire net and non woven fabrics as primary and secondary protection materials. Such protection method was successfully applied to the explosive demolition of 16 and 17-strory apartment buildings.and the results of a simulation on a model tunneling workings using diesel equipments are introduced. In case of typical model of tunneling face, the gas concentration of human height is about one third of roof concentration and right side half of the tunnel shows better environment than left half. NOx concentration of workings can be estimated about 0.45ppm which is much lower than permissible level(5 ppm).

• Journal of Mechanical Science and Technology
• /
• v.20 no.2
• /
• pp.185-190
• /
• 2006

An ultrasonic self-calibrating technique for the characterization of a ceramic which was fabricated by change pressing time during the HIP process has been applied by using the ratio of the reflection and transmission coefficients of normal incidence longitudinal waves. The ratio is self-compensated, in that it is independent of the characteristics for transmission and reception of ultrasound by the transducer and the condition of the couplant. The insensitive direction in parameter space is defined as the direction in which the variation of the ratio to changes of two parameters vanishes. For inverse problem the distribution of minima in an error surface is investigated.

• Advances in concrete construction
• /
• v.8 no.2
• /
• pp.101-117
• /
• 2019

Structural strengthening of reinforced concrete (RC) beams is becoming essential to meet the up-gradation of existing structures due to the infrastructure development. Strengthening is also essential for damaged structural element due to the adverse environmental condition and other distressing factors. This article reviews the state of the field on repair, retrofitting and rehabilitation techniques for the strengthening of RC beams. Strengthening of RC beams using various promising techniques such as externally bonded steel plates, concrete jacketing, fibre reinforced laminates or sheets, external prestressing/external bar reinforcement technique and ultra-high performance concrete overlay have been extensively investigated for the past four decades. The primary objective of this article is to discuss investigations on various strengthening techniques over the years. Various parameters that have been discussed include the flexural capacity, shear strength, failure modes of various strengthening techniques and advances in techniques over the years. Firstly, background information on strengthening, including repair, retrofitting, and rehabilitation of RC beams is provided. Secondly, the existing strengthening techniques for reinforced concrete beams are discussed. Finally, the relative comparisons and limitations in the existing techniques are presented.

• Proceedings of the Korean Reliability Society Conference
• /
• 2005.06a
• /
• pp.131-137
• /
• 2005

In this paper, we propose a Bayesian approach to determine the adaptive preventive maintenance(PM) policy for a general sequential imperfect PM model proposed by Lin, Zuo and Yam(2000) that PM not only reduces the effective age of the system but also changes the hazard rate function. Assuming that the failure times follow Weibull distribution, we adopt a Bayesian approach to update unknown parameters and determine the Bayesian optimal sequential PM policies. Finally, numerical examples of the optimal adaptive PM policy are presented for illustrative purposes.

• Steel and Composite Structures
• /
• v.18 no.2
• /
• pp.325-344
• /
• 2015

Experimental tests on cellular beams with sinusoidal openings showed two main failure modes around the openings. They concern the formation of four plastic hinges and the local instability of the sinusoidal part of the opening. In parallel, numerical analysis of the sinusoidal part of the opening revealed the existence of an elastic rotational restraint between the intermediate web-post and the adjacent opening panel. The aim of the present study is to present an approach to quantify this rotational restraint. Through the response surface method, a mathematical model is proposed. It shows a great ability to predict the rotational restraint value as a function of the geometrical parameters of the opening. This model can be used to perform an extensive study with various geometrical configurations of beams with the aim to develop a reliable and realistic analytical model predicting the resistance of the sinusoidal openings.

• Steel and Composite Structures
• /
• v.10 no.2
• /
• pp.169-185
• /
• 2010

The present work describes the experimental tests on steel and lightweight concrete composite beams performed at University of Minho, Portugal. The study involves tests on simply supported composite beams of 4.5 m span, with the same geometrical disposition, supports and materials. The geometrical configuration for the cross section and supports is identical for every beam, varying the shear connectors' distribution and the loading conditions. Headed studs are used to provide the connection between the steel profile and the concrete slab. The parameters in study are the stud disposition and the load distribution. The main objective is to describe the composite beams behaviour, focused on its connection, and to analyse the contribution of the different components to the beams load and deformation capacity. All the tests explored the beams maximum load and deformation capacity and different types of failure were observed.

• Computers and Concrete
• /
• v.11 no.5
• /
• pp.463-473
• /
• 2013

As known, concrete classes are described as strength of standard specimens produced and kept in ideal conditions, not including reinforcement and not subjected to any load effect before. Under the circumstances, transforming core strengths to the standard specimen strength is necessary and considering all parameters, affected on the core strength, is inevitable. In fact, effects of the reinforcement and the load history on concrete strength are generally neglected when these mentioned transforms are performing. The main purpose of this paper is investigating the effects of the reinforcement and the load history on the core strength. This investigation is experimentally performed on cores drilled from specimens having different keeping conditions, reinforced, unreinforced, subjected to bending and central pressure in various proportions of failure load during specified periods. Obtained results show that the importance of these effects cannot be neglected.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1562-1569
• /
• 2008

In this paper, the study on development of an applicable logic on the characteristics of Rolling stocks will be proposed. In general, this logic which means decision logic or LTA(Logic Tree Analysis) is used to analyze how the failure mode have an effects on the system. The effect would be categorized as safety, operational, economical, etc. To do this, based on the typical logics which have been applied to other industries, such as plants, aero, etc. This paper emphasizes two crucial parameters that is one cost the other customer service, that have an important role in railway system operation. In conclusion, as mentioned above as the logic for which could be effectively applied for the railway system(RST) would be developed.

• Advances in concrete construction
• /
• v.5 no.6
• /
• pp.625-638
• /
• 2017

The flexural behavior of Fiber reinforced polymer (FRP) sheets has gained much research interest in the flexural strengthening of reinforced concrete beams. The study on flexure includes various parameters like increase in strength of the member due to the externally bonded (EB) Fiber reinforced polymer, crack patterns, debonding of the fiber from the structure, scaling, convenience of using the fibers, cost effectiveness, etc. The present work aims to study experimentally about the reasons behind the failure due to flexure of an externally bonded FRP concrete beam. In the design of FRP-reinforced concrete structures, deflection control is as critical as much as flexural strength. A numerical model is created using Finite element (FEM) software and the results are compared with that of the experiment.