• Journal of Biosystems Engineering
• /
• 제41권1호
• /
• pp.1-11
• /
• 2016

Purpose: The gear strength of a new mechanical transmission designed to increase the loading weight of small 4.8 kW tracked agricultural transporters was analyzed. Design improvements to increase the gear strength and reduce the gear weight were proposed after examining the parameters. Methods: Sixteen operators from three regions were surveyed to obtain the usage profile of small 4.8 kW transporters. Gear strength was evaluated by calculating contact stress and tooth root stress using commercial software following ISO 6336. Results: From the strength calculation for each gear pair, contact stress smaller than tooth root stresses were produced in all gear pairs. The safety factors in most cases exceeded 1.0, except in the case of gear pair II in group II. The design life of the transporter using gear pair II in group II was 42% under harsh conditions-thus, this design life needs improvement. A robust design was proposed by examining the relevant parameters (face width and profile shift coefficient) to increase the design life of the transporter. In addition, a lightweight design for gear pair I in group II that was considered overdesigned was proposed by examining the face width to reduce the weight of the drive gear by 42% and that of the driven gear by 30%. Conclusions: The Safety factor for the design life was examined through a gear strength analysis. After examining the relevant parameters, conditions for strength improvement were proposed to increase design life or adjust overdesigned gear. However, load conditions differ depending on the working conditions or user's preferences; therefore, it is necessary to conduct further studies in various regions.

• 한국산업융합학회 논문집
• /
• 제9권4호
• /
• pp.269-276
• /
• 2006

Strength Design method for involute spur gears is developed. The developed gear strength design system can design the optimized gear that minimize the number of pinion teeth with face tooth. Method of optimization is matrix form which is developed from this study. Design variables are transmitted power, gear volume, gear ratio, allowable contact stress and allowable bending stress, etc. Gear design method developed this study can be apply to the gears of plants, machine tools, automobiles.

• 한국안전학회지
• /
• 제12권4호
• /
• pp.39-46
• /
• 1997

This study describes a computer aided design system on involute gear for power transmition. Input data for gear design are pressure angle $20^{\circ}$, transmitted power, gear volume, gear ratio, addendum ratio of rack, dedendum ratio of rack, edge radius of rack, allowable contact stress and allowable bending stress etc. Bending strength contact strength and scoring are considered as the design constraints. Method of optimization developed this study. The developed gear design system can design the optimized gear that minimize the number of pinion teeth with face tooth.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.92-97
• /
• 2004

The aim of this study is to estimate the strength of injection molded plastic stepped gear. We considered stepped gear as plate model which are fixed by two edges. While, on the other sides are free. Normal gear is calculated by Lewis formula which can be derived quite simply from the equation for the stress at the root of a cantilever beam. Stress ratio(step factor) is represented for the ratio of the bending stress of normal and the bending stress of stepped gear, and it is plotted by face width factor. This study is propose the step factor added in Dupont equation which are strength estimation of step gear

• 한국정밀공학회지
• /
• 제3권3호
• /
• pp.40-71
• /
• 1986

By developing a computer program for the systematic design of worm gears, the design formulae and tables of AGMA, JGMA, BS and DIN are analized and compared. The computer program can be used on micro-computers. According to the input data of the reduction ratio, the center distance. the driving torque and the material as design parameters, the program calculate the most efficient worm gear dimension. The variation of the design parameters and other empirical coefficients in case of resulting an inadequate design gear dimension can be easily modified throuth the way of interactive method between the user and the monitoring system of computer. A proposal of the standardization of worm gears was made in which a standard module according to the DIN 323 standard series number was applied. For the more exact and effective calculation of the stress concentration and the deformation of gear teeth, a computer program using the boundary element method is also developed. Even the strength of the special gear shape such as Niemann's "Cavex" gear can be calculated in a short CPU-time. The most effort of this study has been layed on the developing a computer program for the correction of a tooth profile and face width which is most important design factor for an exact and wide teeth contacts under loads, especially by great and wide gears. For this purpose were investigated the tooth stiffness, the mesh interferences and the kinematics and the dynamics of gear mesh. The deflection and the deformation of the gear shaft due to the loads acting on gear and shaft were aslo considered. Some examples have shown the sufficient good status of teeth contact in which the correction of the tooth profile and face width were accomplished due to the calculated results.d results.

• 한국정밀공학회지
• /
• 제13권10호
• /
• pp.36-45
• /
• 1996

The precise estimation of the reliability and life of the Ravigneaux planetary gear train used in an automatic transmission is necessary in order to enable accurate material and geometric properties to reliability distrobution and the number of load cycles at failure. These are critical for the proba- bilistic design of complex planetary gear system as Ravigneaux type particularly during various gear ratios. The Ravigneaux planetary gear train has five gears, such as a forward and a reverse sun gear, a short and a long pinion, and an annulus gear. In this paper, the Ravigneaux gear system is analyzed to figure out the reliablity distribution. i.e. the probability of survival in the system without its overhaul. First, the reliablity method based on the Weibull distribution is used in conjuction with the Palmgren's model to predict both the individual reliabilities of its components and the nimber of load cycles when the system failed. Then using the presented method, the life of the Ravigneaux gear system can be determined. Alwo the different design parameters such as tooth face width, material property, and Weibull exponent are applied and reached to optimal ones. Thus, the precise evaluation of the reliability and life of the Ravigneaux planetary gear train used in an automatic transmission can be effectively carried out.

• 한국기계가공학회지
• /
• 제20권12호
• /
• pp.44-53
• /
• 2021

As environmental issues have emerged worldwide, emission gas regulations have been strengthened. In the construction machinery sector, studies have been actively conducted to utilize the power source of electric motors owing to the increasing demand for zero emissions. In this study, the gear specifications of an electric axle for construction machinery were selected by considering the specifications of the motor, gear tooth contact pattern, and face load factor. The gear strength evaluation was performed at the system level using the simulation model. The bending and contact strength of the spiral bevel gears and the bending strength of the planetary gear set showed a safety factor of 1 or more. However, the contact strength of the planetary gear set showed a safety factor of 0.92. Conservative results were derived by performing the analysis under the rated load condition of the motor. However, the ratio of the equivalent torque to the rated torque of the motor was 45% or less, hence, it was determined that no difficulties should arise regarding the durability of the axle.

• 한국기계가공학회지
• /
• 제14권6호
• /
• pp.63-68
• /
• 2015

Recently, 3D printer technologies have been used in many research efforts for high precision manufacturing. In particular, the rapid prototyping technology has been developing rapidly, because it can be manufactured in a short time with a 3D designed shape. This paper relates to the production characteristics of the straight bevel gear designed using a 3D print using the PolyJet method. The characteristics of a 3D printed straight bevel gear were compared with a machined straight bevel gear. The accuracy of the produced straight bevel gear was evaluated by backlash, meshing pattern, face angle, root angle, and surface roughness.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.200-206
• /
• 2002

Pressure and film thickness of contacting surfaces between teeth of the involute spur gear in lubricated condition were studied by a numerical method. Dynamics of the gear and pinion was considered to gel ail accurate initial clearance between gear teeth. The 3-dimensional non-steady elastohydrodanamic lubrication analysis on the gear teeth showed a slight higher pressure at the inlet region of the contacting face as well as pressure spike at the outlet region and a more thick film thickness than that of steady condition.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.391-392
• /
• 2006

Gears are essential and useful elements which power is transmitted from a source to a driven equipment. Therefore, it is very important to design gears correctly. Two important points in the gear design procedures are capacities of the gears's bending strength and pitting resistance. This paper deals with two subjects about spur and helical gears : analyzing for strength and wear capacities, and design of face width. Also, this paper proposes the analytical program which is developed for computer aided design and analysis This program is based on the American Gear Manufactures Association(AGMA) Standards.