• Transactions of Materials Processing
• /
• v.27 no.6
• /
• pp.379-385
• /
• 2018

This study investigated the effect of extrusion conditions on microstructures and mechanical properties of AM80 magnesium alloys. The billets of magnesium alloy used for hot extrusion were prepared by permanent mold casting method, and its extrusion was hot direct extrusion with different extrusion conditions. The results of microstructural analysis showed that the main phases in the as-casted alloys were ${\alpha}-Mg$, ${\beta}-Mg_{17}Al_{12}$, and lamella $Mg_{17}Al_{12}$. Hot extrusion results, The tensile strength of the most soundly manufactured extruded bars (extrusion temp: $350^{\circ}C$, extrusion ratio: 27:1, ram speed: 2mm/s) was approximately 327MPa at room temperature. The increase in the mechanical properties of hot-extruded alloys was as a result of grain refinement by dynamical recrystallization during hot extrusion.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.50-55
• /
• 2018

The important thing in extrusion technology is the design and production of molds. Appropriate design of the molds is essential for achieving the desired extrusion of molds at the same time to maximize the life of the molds and increase their efficiency. The extrusion temperature and extrusion speed are the main parameters at the time of extrusion. Different extrusion conditions should be added depending on the extrusion ratio, physical properties of the material, and type of extrusion. In this study, the extrusion process of various 6xxx series aluminum cast alloys for high speed train interior or exterior parts were investigated. The extruded die design was performed for the 6063, 6061, 6N01, 6005, 5083 and 6060 alloy profiles and an extrusion test was conducted. In addition, the extrusion conditions, such as extrusion pressure following as the billet temperature, extrusion temperature, and materials change, were analyzed. Although the 6063 aluminum alloy can be extruded at the lowest temperature and pressure, the 6061 alloy can be extruded at the highest temperature and pressure. From these results, the successful extruded products were manufactured from these established conditions.

• Transactions of Materials Processing
• /
• v.18 no.1
• /
• pp.80-86
• /
• 2009

This paper presents the plastic inhomogeneous deformation behavior of bimetal composite rods during the axisymmetric and steady-state extrusion process through a conical die. The rigid-plastic FE model considering frictional contact problem was used to analyze the co-extrusion process with material combinations of Cu/Al. Different cases of initial geometry shape for composite material were simulated under different conditions of co-extrusion process, which includes the interference and frictional conditions. From the simulation results, the sleeve cladding rate at the core/sleeve interface was recorded as a distribution of diameter ratio and interference conditions, which will be useful for the investigations of the bonding process during co-extrusion process. In addition, the results of the co-extrusion, connected with the results of the variations of diameter rate and average contact pressure, demonstrate a good agreement and present the possibility of describing the parameters of the plastic zones in non-uniform deformation of these type of composite materials.

• Journal of Korea Foundry Society
• /
• v.34 no.3
• /
• pp.87-93
• /
• 2014

Thixo-extrusion of semi-solid 7075 aluminum alloy and the mechanical properties of its extrudates were investigated. The semisolid alloy was prepared by a cooling slope cast. In other to perform thixo-extrusion, semi-solid 7075 aluminum alloy billets were reheated at the reheating conditions reported in a previous study. The maximum extrusion pressure in thixo-extrusion was 615MPa. This was lower than that of conventional hot extrusion ($P_{max}=940MPa$) at the same extrusion conditions due to the increased fluidity of the alloy billet in the semi-solid state. The values of Rockwell hardness (scale B) at the extrusion direction of the as thixoextruded bar were 48~53HRB and the difference in Rockwell hardness between the transverse direction and the extrusion direction was 5HRB or less. The results show that thxio-extrusion of semi-solid 7075 Al alloy improves the workability and anisotropic with the extrusion direction compared with hot extrusion of the conventional alloy.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.18 no.34
• /
• pp.35-42
• /
• 1995

In the plastic extrusion process, product quality is influenced by work condition for temperature of cylinders and dies. The work conditions are various, so it is difficult to standardization of the work conditions. Therefore, the work conditions are depended on the workers of experience and skill. In the plastic extrusion process, it has five control heating points on the cylinder and three control heating points on the die. In addition, there is one control point on the extrusion process. It is extrusion speed. In this case, we don't know how these affect product quality. We structure the multiple linear regression equation with the temperature of cylinders and dies as independent variables and the product weight as dependent variable. We solve this equation using statistic computer package named Juse-Qcas.

• Journal of Korea Foundry Society
• /
• v.34 no.4
• /
• pp.123-129
• /
• 2014

This work presents the results of a thixo-extrusion process applied to aluminum alloy and and reheating characteristics of semi-solid A356 Alloy using have been discussed. The reheating experiment was performed using an electric resistance furnace and multi-stage heating for uniform reheating. The thixo-extrusion was performed at the optimal reheating conditions of the semi-solid A356 alloy, the the extrusion conditions were an extrusion ratio of 33 and ram speed of 6 mm/sec. The results showed that the thixo-extrusion of semi-solid A356 alloy fabricated by the cooling slope reduced the extrusion pressure by 180% in comparison with hot extrusion, and that a sound extrusion could be obtained in spite of the same extrusion ratio and strain rate.

• Food Science and Biotechnology
• /
• v.16 no.5
• /
• pp.783-788
• /
• 2007

An advantage to the extrusion of raw potatoes is a reduction in the energy input required to process potato products; however, the effects of extrusion on the properties of raw potato have not been studied. The purposes of this study were to develop a workable extrusion process for raw potato and to study the effects of extrusion conditions on the pasting properties of extruded potato products. The peak viscosity, final viscosity, pasting temperature, water solubility index, and water absorption index of pressed and pressed-dried potato extrudates decreased as die exit temperature increased, whereas they did not change as screw speed increased. The peak viscosity, final viscosity, and water solubility of steam-cooked potato products decreased with extrusion processing; however, they did not change with increasing die exit temperature and screw speed. Potato products with different degrees of depolymerization of extruded potato starch, depending on die exit temperature, were produced from raw potatoes.

• Transactions of Materials Processing
• /
• v.6 no.3
• /
• pp.221-226
• /
• 1997

Chevron crack in cold extrusion has been studied in view of deformation conditions and material characteristics. There is V formed chevron crack is occasionally occurred in core part of shaft by multistage free extrusion. Although many research results were reported and theoretical analyses were accompanied, in this study we discussed practical method to prevent chevron crack in the field of working conditions and material characteristics. We have found that chevron crack is eliminated under condition of high hydrostatic state in deformation and decreased segregation, refinement of micro structure of materials.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.03a
• /
• pp.54-61
• /
• 1995

Simultaneous forward-backward extrusion upsetting has been carried out by ratray forging. Two materials has been used commericaly 6.61 aluminium ally and 0.2% steel. The effects of working conditions ; spiral feed ; initial aspect ration of specimen and lubricating condition on the backward and forward extrusion were clarified. The extrusion length increases a sthe aspect rationof the specimen increases, the backward extrusion lengthbeing relatively larger than the forward one. The effects of the spiral feed and the material on the extrusion lengthis remarkably large for the large spiral feed.

• Transactions of Materials Processing
• /
• v.15 no.8 s.89
• /
• pp.597-602
• /
• 2006

Bulk plastic forming characteristics were studied for the magnesium alloy, AZ31 in warm backward extrusion. Effects of process conditions such as extrusion ratio, forming temperature, and punching speed were investigated respectively. Variation of microstructure induced by the warm backward extrusion process was observed. Microstructure of the work piece showed evidences of recrystallization under the experiment conditions. It is estimated that in specific punch speed region fast stroke accelerates recrystllization and reduces the forming load.