• Journal of the korean academy of Pediatric Dentistry
• /
• 제25권2호
• /
• pp.312-322
• /
• 1998

There are many concerns about the erosive effect of acidic beverage. In this study, the erosive effect of bovine enamel caused by $Pepsi-Cola^{(R)}$(pH 2.41) and rehardening effect by intraoral exposure were determined by microhardness test and SEM. The bovine enamel specimen was imbedded in 100ml $Pepsi-Cola^{(R)}$ during 5 minutes and exposed to the intraoral environment with removable resin plate. The microhardness test was performed after 1 hr, 24 hrs, and 48 hrs. The results obtained from this study can be summarized as follows ; 1. The microhardness value was significantly (p<0.05) reduced by cola beverage, and significantly (p<0.05) increased after 1 hr and 24 hrs respectively. 2. The difference in the microhardness between 24 hrs group and 48 hrs group was not significant (p>0.05) and microhardness value of 48 hrs group was significantly less than that of initial group (p<0.05). 3. The erosive effect of cola beverage and remineralization effect by intraoral exposure were visualized by the SEM photo. But, the enamel surfaces did not return to their original state.

• Journal of Magnetics
• /
• 제10권2호
• /
• pp.52-57
• /
• 2005

In this research, magnetoresistance (MR) ratio (MR), resistivity, and exchange coupling field $(H_{ex})$ behaviors for sputter deposited spin valves with FeMn antiferromagnetic layer have been extensively investigated by rapid thermal annealing (RTA) as well as conventional annealing (CA) method. 10 s of RTA revealed that interdiffusion was not significant up to $325^{\circ}C$ at the interfaces between the layers when the RTA time was short. The MR of FeMn spin valves were reduced when the spin valves were exposed to temperature of $250^{\circ}C$, even for a short time period of 10 s prior to CA. $H_{ex}$ was maintained up to $325^{\circ}C$ of CA when the specimen was subjected to 10 s of RTA at $200^{\circ}C$ prior to CA, which is $25^{\circ}C$ higher than the result obtained from the CA without prior RTA. Therefore, the stability of $H_{ex}$ could be enhanced by a prior RTA before performing CA up to annealing temperature of $325^{\circ}C$. MR and sensitivity of the specimens annealed without magnetic field up to $275^{\circ}C$ were recovered to the values prior to CA, but $H_{ex}$ was not recovered. This means that reduced MR sensitivity and MR during the device fabrication can be recovered by a field RTA.

• Restorative Dentistry and Endodontics
• /
• 제24권4호
• /
• pp.554-559
• /
• 1999

Aucubin, an iridoid glucoside isolated from Aucuba japonica, has pharmacological effects such as antimicrobial effect, liver protective function and inhibition of liver RNA and protein biosynthesis, etc. This study was performed to observe the effect of aucubin on the pulp tissue after pulpotomy. Aucubin was converted to aucubinogenin as an active form by ${\beta}$-glucosidase. In 3 Mongrel dogs, the pulps were mechanically exposed with a sterile round bur and excised with sterile excavator. After bleeding control, aucubin was applied on remaining pulp tissues and then they were sealed with IRM in experimental group. In control group, $Ca(OH)_2$ powder was applied on remaining pulp tissues and then they were sealed with IRM. After interval of 1 and 12 weeks, the dogs were sacrificed. The teeth were prepared for histologic evaluation and examined by light microscope. Aucubin 1 week group showed that mild inflammation and vascular congestion in most of the specimen. More various degree of inflammation was found in experimental group than in control group. Premature calcified mass were found in the both 1 weeks groups. Continuous well-formed dentin bridge was found in both 12 weeks groups. Collectively, this study suggests that the possibility of aucubin as a medicament after pulpotomy.

• Structural Engineering and Mechanics
• /
• 제19권5호
• /
• pp.581-602
• /
• 2005

In this paper the accumulation of local damage during the cyclic loading in reinforced high-strength concrete columns is experimentally investigated. Two identical column specimens with annular cross-section and spiral reinforcement were designed and two tests, up to failure, under the action of a constant vertical concentrated force and a time-dependent concentrated horizontal force, were carried out at the LNEC shaking tables facility. Sine type signals, controlled in amplitude, frequency and time duration were used for these experiments. The concept of local damage based on local stiffness degradation is considered in detail and illustrated by experimental results. The specimens were designed and reinforced in such a way that the accumulation of damage was predicted by dominating deformations (cracking and crushing of the concrete) while the increasing of the loading values was a dominating factor of damage. It was observed that the local damage of HSC columns has exposed their anisotropic local behaviour. The damage accumulation was slightly different from the expected in accordance with the continuum damage concept, and a partial random character was observed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.923-927
• /
• 2017

Metal exposed to high temperature/high pressure/oxidizer-rich environment may cause rapid oxidation(ignition and combustion). Therefore, this study was performed for the selection of metal appropriate for high temperature/high pressure/oxidizer-rich environment. In order to make the high temperature, high pressure and oxidizer-rich environment, the test facility utilizing the catalytic reaction of hydrogen peroxide was constructed and the metal oxidation and ignition of the STS series metals were evaluated. The result showed that the change of the selected material (discoloration) and the surface roughness were observed, but the change in the weight and thickness of the specimen was not significant.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.19-22
• /
• 2011

For underground structures that are exposed to environmental conditions, the declination of the durability of concrete occurs easily because of leakages from high hydraulic pressure and the frequent contact of water due to environmental factors. Therefore this study is to confirm that the leakage reduction of natural inorgnic powder compound applying subsurface structural weak part and make the performance improvement of concrete as an objective. The test was done by making the rebar, flat tie, nail and film infiltration and each of its water tank and cylindrical test body then after pouring water to each of the test body, the test observe the change of the water tank surface absorbed condition and leakage of each specimen with respect to time. As a conclusion, the test was observed that this water proofing admixture has better watertightness from the beginning of the setting time(when it hardens), the ettringite and the thaumasite generates a large quantity of hydration products that controls the formation in a large opening and the CSH produced by pozzolan reaction makes a dent at this opening.

• Restorative Dentistry and Endodontics
• /
• 제19권1호
• /
• pp.180-193
• /
• 1994

The purpose of this study was to observe the sealing ability and durability of All-Bond 2, Gluma Bonding System, Scotch bond 2 and Superbond D-liner which are dentin bonding agents used as desensitizing agents. The durability of the sealing ability of the materials were compared after 0, 140, 420, 840 tooth brushing strokes. 120 extracted teeth were divided into 5 groups and the agents were applied to the exposed dentin. No agents was applied on group I, the control group. Each specimen went through thermocycling from $5^{\circ}$ to $55^{\circ}C$, 200 times. Each group was devide into 4 subgroups and artificial tooth brushing strokes were done for 0, 140, 420, 840 times. Finally the specimens were stored in 0.5 % methylene blue solution for 24 hours in a incubator set at $37^{\circ}C$. The tooth were sectioned perpendicular to the long axis and the dye penetration ratio to the pulp was measured. The following results were obtained. 1. All four dentin bonding agents initially showed excellent sealing ability. 2. All-bond 2, Gluma Bonding System and Superbond D-liner showed durability of dentinal tubule sealing effect after 840 strokes(6-week) artificial tooth brushing. 3. Scotchbond 2 showed a significant decrease in sealing ability after 420 strokes(3-week) artificial tooth brushing. (P<0.05).

• International Journal of Highway Engineering
• /
• 제16권1호
• /
• pp.31-39
• /
• 2014

PURPOSES : Surface treatment material for pavement preventive maintenance should be inspected field applicability. This study(Part II) aimed to checkup coating characteristics and performance analysis using lab and field tests. The hydrophobic - low viscosity filling material for pavement preventive maintenance is presented in Part I, which is a series of companion study. METHODS : Relative comparison between general asphalt mixtures and surface treatment asphalt mixtures are analyzed and measured for the field application such as indirect tensile strength ratio(TSR), abrasion resistance, crack propagation resistance, temperature resistance, coating thickness, permeability resistance and skid resistance in terms of british pendulum number(BPN). RESULTS : It is found that TSR, crack propagation resistance and permeability resistance is increased as against uncoated asphalt specimen. Abrasion resistance and temperature resistance is secured from the initial coating thickness point of view, which is about 0.2~0.3mm. Skid resistance on the surface treatment pavement is satisfied with the BPN criteria of national highway because of exposed aggregate and crack sill induced pavement deterioration and damage cracks. CONCLUSIONS : The hydrophobic - low viscosity surface treatment material for pavement preventive maintenance is validated on field applicability evaluation based on quantitative analysis of coating thickness and performance analysis using lab and field tests.

• Journal of the Korean Society of Industry Convergence
• /
• 제20권2호
• /
• pp.195-204
• /
• 2017

Predicting the failure life of automated manufacturing systems can reduce overall downtime, maintenance costs, and total plant operation costs. Therefore, there is a growing interest in fatigue failure mechanisms as the safety or service life assessment of manufacturing systems becomes an important issue. In particular, fretting fatigue is caused by repeated tangential stresses that are generated by friction during small amplitude oscillatory movements or sliding between two surfaces pressed together in intimate contact. Previous studies in fretting fatigue have observed size effects related to contact width such that a critical contact width exists where there is drastic change in the fretting fatigue life. However, most of them are the two-dimensional finite element analyses based on the plane strain assumption. The purpose of this study is to investigate the contact size effects on the three-dimensional finite element model of a finite width of a flat specimen and a cylindrical pad exposed to fretting fatigue. The contact size effects were analyzed by means of the stress and strain averages at the element integration points of three-dimensional finite element model. This study shows that the fretting fatigue life of manufacturing systems can be predicted by three-dimensional finite element analysis based on SWT critical plane model.

• Fire Science and Engineering
• /
• 제23권3호
• /
• pp.31-39
• /
• 2009

Recently, fire resistance in high-rise building is becoming major problem socially. So it is need of hour to study on fire resistance in buildings. This study estimates fire resistance performance to utilized CFT (Concrete filled steel tube, below CFT) column in the high structure. But it is difficult quantitative evaluation about fire resistant performance of CFT. Therefore, this study made CFT specimen that determine the factor which is strength of concrete and then CFT column was exposed to heating controlled as closely as possible the ISO-834 standard fire curve. Also, tried to analyze internal temperature through nonlinear transient heat flow analysis. And, presumed extant compressive strength on the basis of this.