• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.10
• /
• pp.2426-2436
• /
• 1993

Vibration characteristics of a tire play an important role to judge a ride conformability and sound quality for a passenger car. In this study, the experimental investigation for the sound radiation of a radial tire has been examined. Based on the sound intensity techniques, the sound pressure field and the sound radiation are measured. It turns out that air pressure in tire, tread patterns, and aspect ratio of the tire govern the sound radiation characteristics. Then a numerical analysis for the tire element is conducted. During analysis, the tire element is modelled as an elastic ring. The comparison shows that the numerical output correlates to the experimental data.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.940-945
• /
• 2001

Gasoline engine manufacturers are currently considering designs that will result in low combustion air temperature for improvement of fuel consumption and emission levels. There are a variety of cooling systems that can be used to accomplish this goal. Cooling is therefore normally achieved through a balance of ram and fan action. This paper studies the various systems and compare the cooling performance for several conditions, based on a automotive engine. An experimental analysis was developed to predict the interaction of the fan system and the heat exchangers of the engine cooling system. The local temperature induced by the fan on the cooling system is measured. These experimental result were accomplished using airflow management techniques.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.200-205
• /
• 1992

The classical control theory has been developed successfully for the design of a system controller and has evolved continually. Even though sophisticated simulation techniques and software packages are available, there is still some difficulty in the design of a complex system controller at the desk. So the trial and error method is sometimes used to design a new controller, but it requires excess time and cost. This paper suggests a controller design method through the experimental approach. The basic concept is to adjust gradually the design parameters of the controller to the simulation results and experimental data of a similar real system. This method will be a very useful and easy way to design an accurate and/or optimal controller for a real plant while reducing time and giving a good solution at a reasonable cost.

• Archives of Plastic Surgery
• /
• v.41 no.3
• /
• pp.209-212
• /
• 2014

Microsurgery training in Singapore began in 1980 with the opening of the Experimental Surgical Unit. Since then, the unit has continued to grow and have held microsurgical training courses biannually. The road to becoming a full-fledged reconstructive surgeon requires the mastering of both microvascular as well as flap raising techniques and requires time, patience and good training facilities. In Singapore, over the past 2 decades, we have had the opportunity to develop good training facilities and to refine our surgical education programmes in reconstructive microsurgery. In this article, we share our experience with training in reconstructive microsurgery.

• Journal of Mechanical Science and Technology
• /
• v.18 no.12
• /
• pp.2236-2249
• /
• 2004

The analysis for the three-dimensional fluid flow past tube banks arranged in equilateral-triangular form at Re$\_$max/=4,000 is carried out using a large eddy simulation technique. The governing equations for the mass and momentum conservation are discretized using the finite volume method. Parallel computational techniques using MPI (Message Passing Interface) are implemented in the present computer code. The computation time decreases linearly proportional to the number of used CPUs in the present parallel computation. We obtained the time-averaged streamwise and cross-streamwise velocities and turbulent intensities. The present numerical results are compared with the PIV experimental data and agree generally well with the experimental data.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1594-1599
• /
• 2008

Haptic rendering is a process that provides force feedback during interactions between a user and an object. This paper presents a haptic rendering technique for a telemanipulation system of deformable objects using image processing and physically based modeling techniques. The interaction forces between an instrument driven by a haptic device and a deformable object are inferred in real time based on a continuum mechanics model of the object, which consists of a boundary element model and ${\alpha}$ priori knowledge of the object's mechanical properties. Macro- and micro-scale experimental systems, equipped with a telemanipulation system and a commercial haptic display, were developed and tested using silicone (macro-scale) and zebrafish embryos (micro-scale). The experimental results showed the effectiveness of the algorithm in different scales: two experimental systems applied the same algorithm provided haptic feedback regardless of the system scale.

• Journal of Power Electronics
• /
• v.9 no.2
• /
• pp.207-214
• /
• 2009

This paper presents a modem approach for speed control of a PMSM using the Particle Swarm Optimization (PSO) algorithm to optimize the parameters of the PI-Controller. The overall system simulated under various operating conditions and an experimental setup is prepared. The use of PSO as an optimization algorithm makes the drive robust, with faster dynamic response, higher accuracy and insensitive to load variation. Comparison between different controllers is achieved, using a PI controller which is tuned by two methods, firstly manually and secondly using the PSO technique. The system is tested under variable operating conditions. Implementation of the experimental setup is done. The simulation results show good dynamic response with fast recovery time and good agreement with experimental controller.

• Korean Institute of Interior Design Journal
• /
• v.22 no.1
• /
• pp.97-104
• /
• 2013

This study aims at finding out the characteristics and influences of Libeskind's early drawing works through comparisons of each drawing. The importance of his experimental drawing works is not only their uniqueness but also relationship to creation and development of his architecture. Libeskind's musical and educational background had great impacts on forming his early drawings. A series of drawings including 'Micromegas', 'Chamberworks', and 'Theatrum Mundi' shows variety and experiments about reconstruction of three dimensional architectural fragments, abstractive line drawing and plane oriented painting. Libeskind himself cease to experiment drawing techniques but their characteristics still remain in his sketches, diagram and conceptual drawings. In spite of influences of undergraduate design studios, theoretical background of graduate studies, their experimental features are due to his continuous endeavor to make and develop his drawing skills and contents. As a result, his early drawings act as media and way to communicate and develop his concepts.

• Steel and Composite Structures
• /
• v.28 no.2
• /
• pp.123-138
• /
• 2018

Eccentrically braced frames (EBF) represent an optimal structural solution for seismic prone areas, being able to provide high dissipative capacity and good elastic stiffness, to withstand strong seismic events without significant loss of bearing capacity and to avoid damage to non-structural elements in case of low and moderate earthquakes. The accurate knowledge of the cyclic behaviour of the dissipative links, characterizing the whole performance of EBFs, is required to optimize the structural properties and to refine the design techniques adopted for multi-storey buildings' analysis. Reliable numerical models for the links, at the same time requiring a limited computational effort, are then needed. The present work shows the results of a wide experimental test campaign executed on real-scale one storey/one bay frames with horizontal and vertical links, together with the elaboration of a simple semi-analytical model for the quick representation of the cyclic behaviour of shear links.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.4
• /
• pp.799-806
• /
• 1989

Component mode synthesis (CMS) method can be divided into free, fixed and hybrid interface method according to each component's connecting conditions. In this paper, major mode synthesis methods were reviewed and their accuracies were examined by comparing the calculated eigenvalues with those from full finite element (FE) model. Also, CMS is expanded into the coupling between finite element (FE) and experimental model. Since the assumed experimental data seldom have slope information, the slope information at the interface points is prepared by curve-fitting of the calculated values. A simple beam structure to show the effectiveness of the above method, and we found that it can improve the accuracy of the synthesis method in calculation, expecially in the low modes.