This paper describes organic acid-based wet chemical etching behaviors of amorphous Ga-doped zinc oxide (GZO) thin film sputter-deposited at low temperature (room temperature). Wet etch parameters such as etching time, temperature, and etchant concentration are investigated for formic and citric acid etchants, and their effects on the etch rate, etch residue and the feature of edge line are compared.
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
1999.05a
/
pp.497-500
/
1999
This paper reports on the fabrication and characteristics of recessed gate GaN MESFETs fabricated using a photoelectrochemical wet etching method. The unique etching process utilizes photo-resistive mask and KOH based etchant. GaN MESFETs with successfully recessed gate structure was characterized in terms of dc and RF performance. The fabricated GaN MESFET exhibits a current saturation at $V_{DS}$ = 4 V and a pinch-off at $V_{GS}$ =-3V The peak drain current of the device is about 230mA/mm at 300 K and the value is remained almost same for 500K operation. The $f_{T}$ and $f_{max}$ from the device are 6.357Hz and 10.25 GHz, respectively.y.y.
Journal of the Korean Institute of Electrical and Electronic Material Engineers
/
v.11
no.9
/
pp.705-710
/
1998
Intrinsic gettering is usually to improve wafer quality, which is an important factor for reliable ULSI devices. In order to generate oxygen precipitation in lightly and heavily boron doped silicon wafers with or without high $^75 As^+$ ion implantation, the 2-step annealing method was adopted. After annealing, the were cleaved and etched with th Wright etchant. The morphology of cross section on samples was inspected by FESEM(field emission scanning electron microscopy). The morphology of unimplanted samples was rater rough than that of the implanted. Oxygen precipitation density observed by an optical microscope in lightly boron doped samples was about 3$\times10^6/cm^3$. However, in heavily boron doped samples, the density of oxygen precipitation was largest at $600^{\circ}C$ in 1st annealing, and decreased abruptly until $800^{\circ}C$, But it increased slightly at $1000^{\circ}C$ and was independent with the implantation.
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
1999.05a
/
pp.677-680
/
1999
Rapid developing automation technology enhances the need of sensors. Among many materials, silicon has the advantages of electrical and mechanical property, Single-crystalline silicon has different piezoresistivity on 야fferent directions and a current leakage at elevated temperature, but poly-crystalline silicon has the possibility of controling resistivity using dopping ions, and operation at high temperature, which is grown on insulating layers. Each wafer has slightly different thicknesses that make difficult to obtain the precisely same thickness of a diaphragm. This paper deals with the fabrication process to make poly-crystalline silicon based pressure sensors which includes diaphragm thickness and wet-etching techniques for each layer. Diaphragms of the same thickness can be fabricated consisting of deposited layers by silicon bulk etching. HF etches silicon nitride, HNO$_3$+HF does poly -crystalline silicon at room temperature very fast. Whereas ethylenediamice based etchant is used to etch silicon at 11$0^{\circ}C$ slowly.
Kim, Jong-Pal;Lee, Sang-Woo;Chun, Kuk-Jin;Cho, Dong-Il
Proceedings of the KIEE Conference
/
1998.07g
/
pp.2550-2552
/
1998
The stiction phenomena poses a design constraint in surface micromachining by reducing the releasable size of the microstructure. This problem occurs during the fabrication process of surface micromachined microstructures during the wet etch of sacrificial layers. For the prevention of the sticking problem, the microsctructure is released by sublimation after the substitution of the sacrificial layer etchant with a sublimation material heated above its melting temperature. In the sublimation drying method, the sublimation materials such as p-dichlorobenzene, t-butyl alcohol, and cyclohexane are used. In this paper, a method for designing a sublimation drying system is developed, and its performance is experimentally evaluated.
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
2000.07a
/
pp.557-560
/
2000
Combination of SDB(Si-wafer Direct Bonding) and electrochemical etch-stop in TMAH anisotropic etchant can be used to create a variety of MEMS(Micro Electro Mechanical System). Especially, fabrication of SDB SOI structures using electrochemical etch-stop is accurate method to fabrication of 3D(three-dimensional) microstructures. This paper describes on the fabrication of SDB SOI structures with sealed cavity for MEMS applications and thickness control of active layer on the SDB SOI structure by electrochemical etch-stop. The flatness of fabricated SDB SOI structure is very uniform and can be improved by addition of TMAH to IPA and pyrazine.
VTR 자기헤드의 핵심소재로 사용되는 ferrite는 VTR 의 주기능인 영상의 기록 및 재생역할에 가장 중요한 소재이다. 이러한 종류의 head는 지금까지 mask wet chemical etching과 mechanical Process 에 의해 제작 되어왔다. 그러나 기록용량의 중가로 자기장치의 recording density를 높일것이 요구됨에 따라 자기헤드의 gap width를 줄일 필요가 있게 되었다. 본 연구는 mask와 photoresist를 사용하지 않고 ferrite를 직접 미세가공 하는 laser-induced wet etching을 이용하여 자기헤드의 기록용량을 높이고자 하였다. $Ar^+$ laser ( 파장 514 nm )를 빔 확장기와 렌즈를 사용 하여 직경 $1.8{\mu}m$ 로 집속하고, $100{\sim}500\;mW$의 출력 변화를 주어 실험을 하였다. 인산 수용액 (45, 65, 85 %)을 etchant로 사용하여 $5{\sim}30{\mu}m/sec$의 주사속도로 etching 하여, 미세선폭과 high aspect ratio를 갖는 groove를 얻을 수 있었다.
Cho, Youngji;Yang, Jun-Mo;Lam, Do Van;Lee, Seung-Mo;Kim, Jae-Hyun;Han, Kwan-Young;Chang, Jiho
Applied Microscopy
/
v.44
no.4
/
pp.133-137
/
2014
We suggest a facile transmission electron microscopy (TEM) specimen preparation method for the direct (polymer-free) transfer of layer-area graphene from Cu substrates to a TEM grid. The standard (polymer-based) method and direct transfer method were by TEM, high-resolution TEM, and energy dispersive X-ray spectroscopy (EDS). The folds and crystalline particles were formed in a graphene specimen by the standard method, while the graphene specimen by the direct method with a new etchant solution exhibited clean and full coverage of the graphene surface, which reduced several wet chemical steps and accompanying mechanical stresses and avoided formation of the oxide metal.
An, Jong-Hwan;Lee, Seok-Jun;Kim, Lee-Chul;Hong, Sang-Jeen
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
2007.06a
/
pp.548-549
/
2007
과거 PCB 제조의 주된 화제는 다양한 산업분야의 발전을 위해 한정된 시간 안에 좀 더 많은 PCB를 양산하는 기술 개발에 집중되어 있었지만, 현재는 비정상적인 공정 상태를 파악함으로써 제조 공정 환경에서의 오류를 줄여 전체 수률을 높이는 방법에 시선을 돌리고 있다. PCB 에칭의 경우 에칭 용액의 상태를 실시간으로 모니터링 하는 것이 중요하다. 본 논문에서는 기존 애칭용액의 상태를 판단할 때 사용되는 ORP 센서 대신, RGB 센서를 이용하여 실시간으로 용액의 상태를 모니터링 할 수 있는 시스템을 개발 하였다. 개발된 시스템을 이용하여 기존 ORP 시스템과의 비교 분석을 및 RGB 센서률 이용한 모니터링 방법이 ORP 센서를 이용한 방법 보다 좀 더 쉽고 정확하게 에칭 액의 상태를 모니터링할 수 있다는 것을 확인 하였다.
The plasma polymerized thin film of MMA+Sty was prepared using a capacitively coupled gas-flow-type reactor. This thin films were also delincated by the electron-beam apparatus with an acceleration voltage 30KV, and the pattern in the resist was developed with the gas-flow-type reactor using an argon as an etchant. The effect of discharge power on groth rate and etching rate of the thin film were studied. The molacular structure of the resist was investigated by ESCA and FT-IR.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.