• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.385-385
• /
• 2010

In this work, we have investigated the etching characteristics of $TiO_2$ and selectivity of $TiO_2$ over $SiO_2$ thin films as resistance in ReRAM using the inductively coupled plasma. The etch rate and selectivity were measured by varying the $BCl_3$ addition into Ar plasma. The maximum etchrate was obtained at 110.1nm/min at $BCl_3$/Ar=5sccm/10sccm, 500W for RFpower, -100v for DC-bias voltage, and 2Pa for the process pressure. The etched $TiO_2$ surface was investigated with X-ray photo electron spectroscopy. We explained the etching mechanism in two etch mechanisms, physiclas puttering and chemical reaction.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.276-278
• /
• 1997

The reliable etching process is one of the essential steps in fabricating GaN based-device. High etch rate is needed to obtain a deeply etched structure and perfect anisotropic etched facet is needed to obtain lasing profile. In the research, therefore, we had proposed a planar inductively coupled plasma etcher (Planar ICP Etcher) as a high density plasma source, and studied the etching mechanism using the $CH_4/H_2$/Ar gas mixture. Dry etching characteristics such as etch rate, anisotropic etching profile and so on, for the III-V nitride layers were investigated using Planar ICP Etcher, based on the plasma characteristic as a variation of plasma process parameters.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.124-125
• /
• 2005

ZnS:Mn thin films have attracted great interest as electroluminescence devices. In this study, inductively coupled BCl$_3$/Ar plasma was used to etch ZnS:Mn thin films. We obtained the maximum etch rate of ZnS:Mn thin films was 2209 ${\AA}$/min at a BCl$_3$(20%)/Ar(80%) gas mixing ratio, an RF power of 700 W, a DC bias voltage of-250 V, a total gas flow of 20 sccm, and a chamber pressure of 1 Pa. It was proposed that sputter etching is dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching products.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.107-107
• /
• 2009

본 연구에서는 중성빔을 이용한 Atomic Layer Etching(ALET) system을 이용하여 $ZrO_2$의 atomic layer etching mechanism에 대하여 연구하였다. Ar neutral beam irradiation dose와 $BCl_3$ gas pressure의 변화에 따라 $ZrO_2$ etch rate와 RMS roughness를 관찰했을 때, Ar neutral beam irradiation dose이 $1.485{\times}10^{16}atoms/cm^2{\bullet}cycle$ 이상이고 $BCl_3$ gas pressure가 0.15mTorr 이상 일 때 $ZrO_2$ etch rate은 $1.07\;{\AA}/cycle$의 일정한 값에서 유지됨을 확인하였다. 그리고 ALET와 ICP Etcher을 통해 $ZnO_2$를 각각 식각하여 physically or chemically damage를 비교한 결과, ALET가 기존의 ICP Etcher system보다 $ZrO_2$ 식각공정에 대해 적은 damage를 받는 것을 ARXPS를 통해 관찰 하였다.

• Current Photovoltaic Research
• /
• v.5 no.3
• /
• pp.75-82
• /
• 2017

High efficiency thin film solar cells require an absorber layer with high absorption and low defect, a transparent conductive oxide (TCO) film with high transmittance of over 80% and a high conductivity. Furthermore, light can be captured through the glass substrate and sent to the light absorbing layer to improve the efficiency. In this paper, morphology formation on the surface of glass substrate was investigated by using HF, mainly classified as random etching and periodic etching. We discussed about the etch mechanism, etch rate and hard mask materials, and periodic light trapping structure.

• 전기의세계
• /
• v.28 no.9
• /
• pp.43-50
• /
• 1979

Silicon nitride films were chemically deposited on silicon substrates by reacting SiCl$_{4}$ and NH$_{3}$ in a nitrogen atmosphere at 700~1100 .deg.C. The deposition rate increased rapidly with deposition temperature upto about 1000 .deg.C, and became less temperature dependent above this temperature. The etch rate of films in buffered HF solution decreased, with an increase of deposition temperature, and a heat treatment at a temperature higher than that of the deposition considerably reduced the etch rate. It indicates that the heat treatment resulted in a densification of the films. Surface charge density of 3~4 * 10$^{11}$ /cm$^{2}$ was determined from the C-V characteristics of MNS diode, and it was also found that surface charge density depended on deposition temperature, but not film thickness. The current-voltage characteristics displayed a logI-V$^{1}$2/ dependence in the temperature range of 300~500.deg.K. Measurement of the slope of this characteristics and its dependence on temperature and bias polarity suggest that conduction in sili con nitride films arises from the Poole-Frenkel mechanism.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.4
• /
• pp.169-172
• /
• 2009

We investigated the dry-etching mechanism of the TiN thin film using a $Cl_2$/Ar inductively coupled plasma system. To understand the effect of the $Cl_2$/Ar gas mixing ratio, we etched the TiN thin film by varying $Cl_2$/Ar gas mixing ratio. When the gas mixing ratio was 100% $Cl_2$, the highest etch rate was obtained. The chemical reaction on the surface was investigated with X-ray photoelectron spectroscopy (XPS). Scanning electron microscopy (SEM) was used to examine etched profiles of the TiN thin film.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.98-100
• /
• 2004

In this study, PST thin films were etched with inductively coupled $Cl_2/(Cl_2+Ar)$ plasmas. The etch characteristics of PST thin films as a function of $Cl_2/(Cl_2+Ar)$ gasmixtures were analyzed by using quadrupole mass spectrometer (QMS). Systematic studies were carried out as a function of the etching parameters, including the RF power and the working pressure. The maximum PST film etch rate is 56.2 nm/min, because a small addition of $Cl_2$ to the $Cl_2$/Ar mixture increased the chemical effect. It was proposed that sputter etching is the dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching products.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.187-190
• /
• 2004

In this study, PST thin films were etched with inductively coupled $Cl_2/(Cl_2+Ar)$ plasmas. The etch characteristics of PST thin films as a function of $Cl_2/(Cl_2+Ar)$ gasmixtures were analyzed by using quadrupole mass spectrometer (QMS). Systematic studies were carried out as a function of the etching parameters, including the RF power and the working pressure. The maximum PST film etch rate is 56.2 nm/min, because a small addition of $Cl_2$ to the $Cl_2/Ar$ mixture increased the chemical effect. It was proposed that sputter etching is the dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching products.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.834-837
• /
• 2004

BST thin films were etched with inductively coupled $CF_4(C1_2+Ar)$ Plasmas. The maximum etch rate of the BST thin films was 53.6 nm/min for a 10 % $CF_4$ to the $Cl_2/Ar$ gas mixture at RF power of 700 W, DC bias of -150 V, and chamber pressure of 2 Pa. Small addition of $CF_4$ to the $Cl_2/Ar$ mixture increased chemical effect. Consequently, the increased chemical effect caused the increase in the etch rate of the BST thin films. To clarify the etching mechanism, the surface reaction of the BST thin films was investigated by X-ray photoelectron spectroscopy.