• Journal of electromagnetic engineering and science
• /
• v.4 no.4
• /
• pp.168-174
• /
• 2004

A bandwidth-enhanced and phase noise-improved differential LC-tank VCO is proposed in this paper. By connecting the varactors to the bases of the cross-coupled transistors of the proposed LC-tank VCO, its input negative resistance has been widened. Also, the feedback capacitor Cc in the cross-coupling path of the proposed LC-tank VCO attenuates the output common-mode level modulated by the low-frequency noise because the modulated common-mode level jitters the varactor bias point and degrades phase noise. Compared with the fabricated conventional LC-tank VCO, the proposed LC-tank VCO demonstrates $200\;\%$ enhancement in tuning range, and 6 - dB improvement in phase noise at 6 MHz offset frequency from 5.4-GHz carrier. We achieved the phase noise of - 106 dBc/Hz at 6 MHz offset, and $10\;\%$ tuning range from the proposed LC-tank VCO. The proposed LC-tank VCO consumes 12 mA at 2.5 V supply voltage.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1218-1220
• /
• 1992

This paper presents the three section sliding mode control algorithm based on variable structure current controller design in a synchronous frame and indirect field oriented control method, and applies it to the position control of induction motor. This control scheme solves the problem of robustness loss during the reaching phase that occurs in a conventional VSC strategy, and ensures the stable sliding mode and robustness enhancement throughout an entire response. As the performance of a VSI fed induction motor drives depends on the characteristics of inner loop current controller, it is desired that the current controller have the fast tracking and robust nature. Therefore, we introduced the voltage mapping table based on the concept of voltage space vector for variable structure current control, and implemented fully digital control system using 16-bit microcontroller with on-chip peripherals without additional processing circuits. Simulation and experimental results confirm the validity of this control scheme for robust AC servo drive system of VSI fed induction motor.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.6
• /
• pp.864-871
• /
• 2015

Recently, one of the main research on the power distribution system is the microgrid. The microgrid is a combination of power sources and loads, which is controllable and has separable connection. The main objective of microgrid is the deployment of the renewable clean energy and the enhancement of load-side reliability. The modern power sources and loads have DC I/O interfaces, which is the major advantage of DC microgrid compared to the conventional AC grid. The components in the microgrid have diverse features, so there is need of proper coordination control. For achieving economic feature, the active power of renewable energy resources is regarded as major control parameter and the whole operation modes of DC microgrid are defined, and the proper operations of each component are described. From the inherent characteristics of DC, there are two control variables: voltage and active power. Through analysis of operation modes, it is possible to determine exact control objectives and optimized voltage & power control strategy in each mode. Because of consideration of whole operation modes, regardless of the number and capacity of components, this coordination control method can be used without modification. This paper defines operation mode of DC microgrid with several DC sources and suggests economic and efficient coordinated control methods. Simulation with PSCAD proves effectiveness.

• Journal of the Korean Society of Visualization
• /
• v.3 no.2
• /
• pp.51-56
• /
• 2005

Acoustic excitations were imposed to coaxial air jet of non-premixed jet flame with hydrogen gaseous injected axially in the center of the flow. The frequencies of excitation were three dominant resonant frequencies at 1L, 2L, 3L. modes including specially 514 Hz (2L-mode) which was estimated theoretically as longitudinal mode of combustor characteristics. The mixing enhancement by acoustic forcing has been investigated quantitatively using PLIF and PIV. The effect of acoustic excitation on combustion process was significant to enhance mixing rate that coincides with specific resonant frequencies. And the behavior of vortex-interaction on flame structure was a good evidence to investigate the phenomenon of shear/mixing layer of fuel-air jet structure. The results obtained in this study concludes that generated streamwise vortex by acoustic excitation has a potential to enhance the mixing rate and abating NOx emissions.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.1
• /
• pp.117-129
• /
• 1998

Micro-hole drilling (holes less than 0.5 mm in diameter with aspect ratio larger than 10) is recently having more attention in a wide spectrum of precision production industries. Alternative methods such as EDM. laser drilling, etc. can sometimes replace the mechanical micro-hole drilling but are not acceptable in PCB manufacture because of the inferior hole quality and accuracy. The major difficulties in micro-hole drilling are related to small signal to noise ratios, wandering motions of the inlet stage, high aspect ratios, high temperatures and so forth. Of all the difficulties. the most undesirable one is the increase of drilling force as the drill proceeds deeper into the hole. This is caused mainly from the chip effects. Peck-drilling is thus widely used for deep hole drilling despite that it suffers from low productivity. In the paper, a method of cutting force regulation is proposed to achieve continuous drilling. A PD and a sliding mode control algorithms were implemented through controlling the spindle rotating frequency. Experimental results show that the sliding mode control reduces the nominal cutting force and the variation of the cutting force better than the PD control. The advantages of the regulation, such as increase of drill life, fast stabilization of a wandering motion, and the precise positioning of the hole are verified in experiment.

• Journal of the Korean Vacuum Society
• /
• v.17 no.2
• /
• pp.170-174
• /
• 2008

We have studied, using Raman and photoluminescence (PL) spectroscopy, material property changes of single-walled carbon nanotubes (SWCNTs) dispersed in sodium dodecyl sulfate(SDS) aqueous solution by ultrasonication. Radial breathing mode Raman intensities of the dispersed SWCNTs shows different behavior depending on their chiralities as the sonication time increases. As the amount of SWCNTs dispersed in 1wt% SDS solution increases, both a downshift of the G-band Raman frequency and an enhancement in the PL intensity were observed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.1
• /
• pp.68-79
• /
• 1992

In the high speed analog system satellite communication system, video signal processing and optical fiber interface circuits, GaAs high gain operational amplifier is advantageous due to obtain a high gain because of its low transconductance and other drawbacks, such as low frequency dispersion and process variation. Therefore in this paper, a circuit techniques for improving the voltage gain for GaAs MESFET amplifier is presented. Also, various types of existing current mirror and current mirror proposed are compared.To obtain the high differential gain, bootstrap gain enhancement technique is used and common mode feedback is employed in differential amplifier.The simulation results show that gain is higher than that of basic amplifier about 18.6dB, and stability and frequency performance of differential amplifier are much improved.

• Computers and Concrete
• /
• v.15 no.2
• /
• pp.141-166
• /
• 2015

In the present study, a Finite Element Model has been developed and used to study the effect of diameter to wall thickness ratio (D/t) of steel tube filled with concrete under axial loading on its behavior and load carrying capacity. The model is verified by comparing its findings with available experimental results. Influence of thickness and area of steel tube on strength, ductility, confinement and failure mode shapes has been studied. Strength enhancement factors, load factor, confinement contribution, percentage of steel and ductility index are defined and introduced for the assessment. A parametric study by varying length and thickness of tube has been carried out. Diameter of tube kept constant and equals to 140 mm while thickness has been varied between 1 mm and 6 mm. Equations were developed to find out the ultimate load and confined concrete strength of concrete. Variation of lateral confining pressure along the length of concrete cylinder was obtained and found that it varies along the length. The increase in length of tubes has a minimal effect on strength of tube but it affects the failure mode shapes. The findings indicate that optimum use of materials can be achieved by deciding the thickness of steel tube. A better ductility index can be obtained with the use of higher thickness of tube.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.975-979
• /
• 2008

Since tram has the advantages to reduce construction cost of infrastructure, to improve accessibility of passengers, and to offer visual pleasures, nowadays, it is one of light rails attracting public attention. Tram can be classified into two groups, one is a conventional steel-wheeled type, and the other is a rubber-tired type (bi-modal tram). The bi-modal tram propelled by the serial CNG hybrid propulsion unit has been developing since 2003 in Korea, which can realize both scheduled operation of railway and route flexibility of bus. Because the bimodal will be operated on both railway mode and bus mode, however, specific criteria and regulations for its design, certification, construction, operation and maintenance have not been determined definitely yet. In consideration of mobility enhancement for the old and the handicapped, motor vehicle safety standard and urban transit (railway vehicle) safety standard, several design specifications were proposed for car body and interiors of the bimodal tram vehicle. The design specifications proposed in this paper can be expected to promote passengers' comfort and safety, operation efficiency of the bimodal tram.

• ETRI Journal
• /
• v.38 no.1
• /
• pp.133-140
• /
• 2016

This paper presents a method of parasitic inductance reduction for high-speed switching and high-efficiency operation of a cascode structure with a low-voltage enhancement-mode silicon (Si) metal-oxide-semiconductor field-effect transistor (MOSFET) and a high-voltage depletion-mode gallium nitride (GaN) fielde-ffect transistor (FET). The method is proposed to add a bonding wire interconnected between the source electrode of the Si MOSFET and the gate electrode of the GaN FET in a conventional cascode structure package to reduce the most critical inductance, which provides the major switching loss for a high switching speed and high efficiency. From the measured results of the proposed and conventional GaN cascode FETs, the rising and falling times of the proposed GaN cascode FET were up to 3.4% and 8.0% faster than those of the conventional GaN cascode FET, respectively, under measurement conditions of 30 V and 5 A. During the rising and falling times, the energy losses of the proposed GaN cascode FET were up to 0.3% and 6.7% lower than those of the conventional GaN cascode FET, respectively.