• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.112-120
• /
• 2005

The injector, which is used in a 4-valve gasoline engine, is required to be maintained the dual stream because of the design of dual intake port. In addition, the spray characteristics of fuel injector have strong influence on engine performance, exhaust emission, fuel consumption, and especially the cold start condition for the port injection. So, commercial gasoline injectors off different type were inspected. Those are 2 hole,4 hole, air shroud 4 hole, and air shroud 4 hole injector with separator. The spray behavior of dual stream was researched by the visualization system and PDPA system was employed to measure the droplet size. Atomization is one of the most important characteristic, so droplet size distributions and SMD are investigated. And the spray characteristics of each injector are also analyzed such as the spray tip penetration, spray angle, and separation angle.

• 한국연소학회지
• /
• 제18권1호
• /
• pp.27-33
• /
• 2013

Hydrogen-dimethy ether(DME) partially premixed compression ignition(PCCI) engine combustion was investigated in a single cylinder compression ignition engine. Hydrogen and DME were used as low carbon alternative fuels to reduce green house gases and pollutant. Hydrogen was injected at the intake manifold with an injection pressure of 0.5 MPa at fixed injection timing, $-210^{\circ}CA$ aTDC. DME was injected directly into the cylinder through the common-rail injection system at injection pressure of 30 MPa. DME inejction timing was varied to find the optimum PCCI combustion to reduce CO, HC and NOx emissions. When DME was injected early, CO and HC emissions were high while NOx emission was low. As the DME injection was retarded, the CO and HC emissions were decreased due to high combustion efficiency. NOx emissions were increased due to the high in-cylinder temperature. When DME were injected at $-30^{\circ}CA$ aTDC, reduction of HC, CO and NOx emissions was possible with high value of IMEP.

• 한국항공우주학회지
• /
• 제38권6호
• /
• pp.596-604
• /
• 2010

이중램제트(이중연소 및 이중모드) 추진기관의 작동특성 및 주요 설계인자를 파악하기 위하여 램제트/스크램제트 추진기관에 대한 공기 및 열역학적 관점에서 이론적인 분석을 수행하였다. 엔진의 효율계수를 적용한 열역학 사이클 해석을 수행하여 각 추진기관의 성능특성을 파악하고, 흡입구 성능 특성, 연소기 입구 마하수, 연소기 형상 및 당량비(연료분사량)에 따른 성능민감도를 분석하였다. 이를 바탕으로 이중램제트 추진기관의 성능설계방향을 제안한다.

• 한국분무공학회지
• /
• 제16권1호
• /
• pp.1-6
• /
• 2011

In recent years, the need for more fuel-efficient and lower-emission vehicles has driven the technical development of alternative fuels such as LPG (Liquefied Petroleum Gas) which is able to meet the limits of better emission levels without many modifications to current engine design. LPG has a high vapor pressure and lower viscosity and surface tension than diesel and gasoline fuels. These different fuel characteristics make it difficult to directly apply the conventional gasoline or diesel fuel pump. Self acting lubricated groove design or coating can be used in high-speed and high precision spindle system like a roller-vane type fuel pump, because of its advantages such as low frictional loss, low heat generation, averaging effect leading better running accuracy and simplicity in manufacturing. Those design method can also affect the atomization of fuel from the injector and the formation of fuel film on the intake manifold. In this study, experiments are carried out to get performance characteristics of initial and steady state operation, The characteristics of vane type fuel pump were investigated to access the applicability on LPLi engine.

• 한국수소및신에너지학회논문집
• /
• 제16권1호
• /
• pp.66-73
• /
• 2005

Hydrogen linear power system is estimated as the next generation power system which can obtain a performance as same as fuel cell. In order to develop Hydrogen combustion power system with high thermal efficiency, it is very important to understand the basic characteristics of hydrogen combustion and establish combustion stabilization technique of its system. In this study, RICEM(Rapid Intake Compression Expansion Machine) for researching of hydrogen combustion linear power system was manufactured and evaluated, and the basic characteristics of linear RICEM were analyzed.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권6호
• /
• pp.894-905
• /
• 2004

The closed cycle diesel propulsion system is free from the problem of the intake air, exhaust gas and their control that are associated with the conventional diesel propulsion system. The system is composed of a main engine, an exhaust cooler. a $CO_2$ scrubber and a $O_2$ mixer. In this paper, a hardware using microprocessor is proposed in order to monitor and control the oxygen and ratio of specific heat for underwater diesel propulsion system. Also simulation is carried out to ascertain the performance of proposed system.

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.7-12
• /
• 2012

Cooled EGR system is widely used to reduce NOx emissions in diesel engine. But when EGR rate was increased, combustion stability was worsened and PM level was increased. So determining optimized control point of EGR rate is important. In order to determine this point, it is important to figure out the effect of EGR system on the exhaust emissions. In this research, NOx and PM emissions were analyzed with various coolant temperature supplied to the EGR cooler at several positions such as downstream of turbocharger, upstream and downstream of DPF. Effects of some variables such as EGR rate, hot / cooled EGR and change of injection timing were estimated. And $CO_2$ emissions were measured at exhaust and intake manifold to calculate EGR rate at each engine operating condition. Also combustion analysis was performed in each engine operating conditions. In the result of this study, there was trade-off between NOx emissions and PM emissions. When EGR rate was increased, combustion pressure was decreased and COV of IMEP was increased.

• 한국가스학회지
• /
• 제19권6호
• /
• pp.1-7
• /
• 2015

지구온난화와 화석연료 고갈 문제의 해결을 위하여 대체 연료 개발에 많은 노력을 하고 있다. 암모니아(NH3)는 수소와 마찬가지로 탄소를 포함하고 있지 않으면서 대표적인 수소 캐리어이다. 또한, 상온에서 0.6 MPa 정도의 압력을 가하면 액상을 유지할 수 있어 LPG 충전인프라를 그대로 사용가능한 장점이 있다. 본 연구는 암모니아를 가솔린과 함께 혼소시켰으며, 혼소 비율에 따른 엔진 성능을 비교하였다. 암모니아와 가솔린의 혼소를 위하여 가솔린 인젝터와 암모니아용 인젝터를 각각 사용하였으며, 암모니아는 액상으로 분사시켰다. 암모니아-가솔린 혼소 엔진의 최대 장점은 가솔린 대체량에 비례하여 이산화탄소 배출량을 크 게 감소시킬 수 있다는 것이다. 하지만 암모니아-가솔린 혼소율에 따라 연소가 불안정한 구간이 있었으며, 암모니아 혼소 비율 0.7 이상에서는 연소 불안정성 증가로 인해 토크와 NOx 배출량이 감소하고, THC 배출량이 급증하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.1639-1645
• /
• 2007

The Diesel Multiple Units (DMU) can be classified into three types by the type of the transmission. One of those is a Diesel Hydraulic Multiple Unit which is operated with a hydraulic transmission and its propulsion system consists of a diesel engine, transmission, cooling unit, fuel system, intake air and exhaust system, etc. In designing and integrating the propulsion system components, the operation and environment conditions should be considered as well as related standards. This paper describes points to be considered on design with related to propulsion system of Diesel Hydraulic Multiple Unit that is now being developed for Turkish Republic State Railway -TCDD.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권4호
• /
• pp.423-429
• /
• 2012

밀러 사이클은 저배기 및 고효율 달성으로 Tier II 규제뿐만 아니라 $CO_2$ 저감을 동시에 달성할 수 있는 기술로 알려져 있다. 그러나 이를 위해서는 충분한 흡입공기량이 확보되어야 하며 흡기계통은 공기저항을 최소화할 수 있는 형상으로 개선되어야 한다. 본 연구에서 흡기계통 설계 및 사이클 해석에 활용하기 위한 기초 자료 확보를 위해 흡기밸브의 유량계수를 측정하였다. 유량계수 측정에는 정상유동장치를 이용하였다. 중속 박용기관에 사용되는 포핏 밸브를 대상으로 실험을 수행한 결과, 흡기밸브 유량계수는 밸브양정의 증가에 따라 약 0.62까지 지속적으로 증가하는 경향이며 행정/보어 비와는 무관한 흡기밸브 고유의 특성이 있음을 확인하였다.