• 전기화학회지
• /
• 제15권3호
• /
• pp.115-123
• /
• 2012

리튬이차전지의 수요가 소형 휴대용 전자기기에서 중대형 전기자동차와 에너지저장장치로 변화함에 따라, 요구되는 전지 특성도 크게 달라지고 있다. 10년 이상의 장기 신뢰성, 팩 수준의 안전성, 가격 경쟁력 확보 등 기존 소형 전지보다 크게 강화된 요구 조건뿐만 아니라, 고출력 특성도 함께 필요로 한다. 그런데, 출력을 측정하기 위해서는 전압과 전류가 동시에 측정 및 제어되어야 하기 때문에, 기존의 단위셀 용량 측정보다 훨씬 어렵다. 또한, 측정 방법의 선택뿐만 아니라 출력유지시간, 충전상태(State-of-Charge, SOC), Cut-off 조건, 측정온도 등의 측정 조건에 따라서도 그 측정값이 크게 달라지는 경향이 있다. 본 논문에서는 HPPC (Hybrid Pulse Power Characterization)법, J-pulse(Japan Electric Vehicle Association Standards, JEVS D 713)법, 정출력 측정법(Constant Power Measurement)의 측정 원리 및 실제 실험에 어떻게 적용해야 하는지 설명하고, HEV(Hybrid Electric Vehicle)용 단위셀을 이용해 출력법간 측정 결과를 비교 분석한다.

• 공업화학
• /
• 제24권5호
• /
• pp.489-493
• /
• 2013

기존의 EDLC용 활성탄소 대신 리튬이차전지용 탄소류 음전극(천연흑연, 인조흑연, 하드카본, MCMB)을 이용해 리튬이온 커패시터를 구성하면 리튬의 층간 삽입반응으로 인해 기존의 물질보다 에너지 밀도가 큰 전극소재를 개발할 수 있을 것이다. 이 실험에서는 기존 리튬이차전지 음극용 탄소 물질을 대칭 전극으로 사용하여 코인형 커패시터를 제조하여 성능을 측정하였다. 또한 리튬을 미리 삽입시킨 탄소류 전극을 이용한 커패시터를 제조한 후 성능을 측정한 결과, 축전현상이 일어나는 것을 알 수 있었다. 즉 전해액에서 전하분리에 의한 리튬이온의 이동을 보충할 수 있다면 기존의 리튬이온은 탄소류 전극의 층간으로 확산되어 들어가 기존의 대칭성 탄소류 전극의 경우에 비해 축전 용량이 증가한다. 또한 표면적이 매우 큰 graphene oxide를 사용하여 위와 같이 실험한 결과 용량이 크게 나왔으며 이로부터 슈퍼커패시터 전극용 물질에는 높은 비표면적이 중요한 요소로 작용한다는 것을 알 수 있었다.

• Journal of Electrochemical Science and Technology
• /
• 제5권1호
• /
• pp.1-18
• /
• 2014

Li-air cell is an exotic type of energy storage and conversion device considered to be half battery and half fuel cell. Its successful commercialization highly depends on the timely development of key components. Among these key components, the catalyst (i.e., the core portion of the air electrode) is of critical importance and of the upmost priority. Indeed, it is expected that these catalysts will have a direct and dramatic impact on the Li-air cell's performance by reducing overpotentials, as well as by enhancing the overall capacity and cycle life of Li-air cells. Unfortunately, the technological advancement related to catalysts is sluggish at present. Based on the insights gained from this review, this sluggishness is due to challenges in both the commercialization of the catalyst, and the fundamental studies pertaining to its development. Challenges in the commercialization of the catalyst can be summarized as 1) the identification of superior materials for Li-air cell catalysts, 2) the development of fundamental, material-based assessments for potential catalyst materials, 3) the achievement of a reduction in both cost and time concerning the design of the Li-air cell catalysts. As for the challenges concerning the fundamental studies of Li-air cell catalysts, they are 1) the development of experimental techniques for determining both the nano and micro structure of catalysts, 2) the attainment of both repeatable and verifiable experimental characteristics of catalyst degradation, 3) the development of the predictive capability pertaining to the performance of the catalyst using fundamental material properties. Therefore, under the current circumstances, it is going to be an extremely daunting task to develop appropriate catalysts for the commercialization of Li-air batteries; at least within the foreseeable future. Regardless, nano materials are expected to play a crucial role in this field.

• 폴리머
• /
• 제29권4호
• /
• pp.375-379
• /
• 2005

생분해성 고분자인 poly(L-lactic acid) (PLLA)에 판상구조의 몬모릴로나이트(montmorillonite, MMT)를 첨가하여 필름형태의 나노복합재료를 제조하고, 무기나노입자의 첨가유무와 가수분해 전후의 열적 특성, 점탄성 특성, 모폴로지 등을 조사하였다. PLLA/MMT 나노복합재료의 XRD 분석결과와 TEM 사진으로부터 MMT 입자가 PLLA에 박리 및 분산되어 있음을 확인하였으며, 가수분해가 진행됨에 따라 U 결정 영역의 상대적인 양이 증가하므로 용융에너지 (${\Delta}H_m$가 더 필요함을 알 수 있었다. MMT를 첨가한 경우에 MMT가 강화제 역할을 하기 때문에 저장탄성률이 더 높은 값을 가졌는데, 이는 PLLA를 나노복합화하였을 때 인장강도, 충격강도 등의 기계적 물성이 증가한다는 이전의 연구와도 잘 일치하였다. 또한. 가수분해 전/후의 SEM사진으로부터, 표면에 스피노달(spinodal) 분해에 의한 거칠고 원형의 구멍들이 생겼음을 관찰할 수 있었으며, 가수분해가 진행됨에 따라 나노복합재료는 원형의 구멍들의 크기가 가수분해전보다 더 커졌을 뿐 원래의 형상을 유지하였다. 본 연구를 통하여 PLLA/MMT나노복합재료의 생분해 속도와 열적, 기계적 특성의 조절 가능성을 제시하였다.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.1-9
• /
• 2014

The vast stores of biomass available in the worldwide have the potential to displace significant amounts of petroleum fuels. Fast pyrolysis of biomass is one of several paths by which we can convert biomass to higher value products. The wood pyrolysis oil (WPO) has been regarded as an alternative fuel for petroleum fuels to be used in diesel engine. However, the use of WPO in a diesel engine requires modifications due to low energy density, high water contents, high acidity, high viscosity, and low cetane number of the WPO. One possible method by which the shortcomings may be circumvented is to co-fire WPO with other petroleum fuels. WPO has poor miscibility with light petroleum fuel oils; the most suitable candidates fuels for direct fuel mixing are methanol or ethanol. Early mixing with methanol or ethanol has the added benefit of significantly improving the storage and handling properties of the WPO. For separate injection co-firing, a WPO-ethanol blended fuel can be fired through diesel pilot injection in a dual-injection dieel engine. In this study, the performance and emission characteristics of a dual-injection diesel engine fuelled with diesel (pilot injection) and WPO-ethanol blend (main injection) were experimentally investigated. Results showed that although stable engine operation was possible with separate injection co-firing, the fuel conversion efficiency was slightly decreased due to high water contents of WPO compare to diesel combustion.

• 한국초전도ㆍ저온공학회논문지
• /
• 제16권3호
• /
• pp.21-25
• /
• 2014

As wireless power transfer (WPT) technology using strongly coupled electromagnetic resonators is a recently explored technique to realize the large power delivery and storage without any cable or wire, this technique is required for diffusion of electric vehicles (EVs) since it makes possible a convenient charging system. Typically, since the normal conducting coils are used as a transmitting coil in the CPT system, there is limited to deliver the large power promptly in the contactless EV charging system. From this reason, we proposed the combination CPT technology with HTS transmitting antenna, it is called as, superconducting contactless power transfer for EV (SUWPT4EV) system. As the HTS coil has an enough current density, it can deliver a mass amount of electric energy in spite of a small scale antenna. The SUCPT4EV system has been expected as a noble option to improve the transfer efficiency of large electric power. Such a system consists of two resonator coils; HTS transmitting antenna (Tx) coil and normal conducting receiver (Rx) coil. Especially, the impedance matching for each resonator is a sensitive and plays an important role to improve transfer efficiency as well as delivery distance. In this study, we examined the improvement of transmission efficiency and properties for HTS and copper antennas, respectively, within 45 cm distance. Thus, we obtained improved transfer efficiency with HTS antenna over 15% compared with copper antenna. In addition, we achieved effective impedance matching conditions between HTS antenna and copper receiver at radio frequency (RF) power of 370 kHz.

• 동력기계공학회지
• /
• 제20권5호
• /
• pp.29-36
• /
• 2016

Aluminum alloys have been widely used in engine materials, cold & hot-water storage vessels and piping etc., Furthermore, the aluminum alloy of AC8A have been widely used in mold casting material of engine piston for various vehicles because of its properties of temperature, wear and corrosion resistance. Therefore, it is considered that evaluation of corrosion resistance as well as wear resistance of AC8A material is also important to improve its property and to prolong its lifetime. In previous paper, the effect of solution($510^{\circ}C$:4hrs) and tempering($190^{\circ}C$: 16, 24, and 36 hrs)heat treatments to corrosion resistance and hardness were investigated using electrochemical method. In this study, in order to examine completely the effect of the tempering hours to hardness variation and corrosion resistance, the results of solution($510^{\circ}C$:4hrs) and tempering($190^{\circ}C$: 2, 4, 8 and 12hrs)heat treatments to hardness and corrosion resistance were investigated using electrochemical method. The hardness decreased with solution heat treatment compared to mold casting condition, but its value increased with tempering heat treatment. Furthermore, the corrosion resistance increased with decreasing of the hardness, and decreased with increasing of the hardness reversely. And the tempering heat treatment temperature at $190^{\circ}C$ for 8 hrs exhibited the highest value of the hardness and also indicated the highest corrosion current density. However, the values of hardness and corrosion current density was again increasingly decreased with increasing of tempering hours than 8 hrs, Consequently, it is suggested that decision of the optimum. tempering hours is very important to improve the corrosion or wear resistance.

• Corrosion Science and Technology
• /
• 제11권6호
• /
• pp.280-285
• /
• 2012

Aluminum is on active metal, but it is well known that its oxide film plays a role as protective barrier which is comparatively stable in air and neutral aqueous solution. Thus, aluminum alloys have been widely applied in architectural trim, cold & hot-water storage vessels and piping etc., furthermore, the aluminum alloy of AC8A have been widely used in mold casting material of engine piston because of its properties of temperature and wear resistance. In recent years, the oil price is getting higher and higher, thus the using of low quality oil has been significantly increased in engines of ship and vehicle. Therefore it is considered that evaluation of corrosion resistance as well as wear resistance of AC8A material is also important to improve its property and prolong its lifetime. In this study, the effect of solution and tempering heat treatment to corrosion and wear resistance is investigated with electrochemical method and measurement of hardness. The hardness decreased with solution heat treatment compared to mold casting condition, but its value increased with tempering heat treatment and exhibited the highest value of hardness with tempering heat treatment temperature at $190^{\circ}C$ for 24hrs. Furthermore, corrosion resistance increased with decreasing of the hardness, and decreased with increasing of the hardness reversely. As a result, it is suggested that the optimum heat treatment to improve both corrosion and wear resistance is tempering heat treatment temperature at $190^{\circ}C$ for 16hrs.

• KEPCO Journal on Electric Power and Energy
• /
• 제1권1호
• /
• pp.115-120
• /
• 2015

$K_2CO_3$-based dry regenerable sorbents were prepared by spray-drying techniques to improve mass produced $K_2CO_3-Al_2O_3$ sorbents (KEP-CO2P, hereafter), and then tested for their $CO_2$ sorption capacity by a $2,000Nm^3/h$ (0.5 MWe) $CO_2$ capture pilot plant built for Unit 3 of the Hadong thermal power station in 2010. Each of the sample sorbents contained 35 wt.% $K_2CO_3$ as the active materials with various support materials such as $TiO_2$, MgO, Zeolite 13X, $Al_2O_3$, $SiO_2$ and hydrotalcite (HTC). Their physical properties and reactivity were tested to evaluate their applicability to a fluidized-bed or fast transport-bed $CO_2$ capture process. The $CO_2$ sorption capacity and percentage utilization of $K_2CO_3$-MgO based sorbent, Sorb-KM2, was $8.6g-CO_2/100g$-sorbents and 90%, respectively, along with good mechanical strength for fluidized-bed application. Sorbs-KM2 and KT were almost completely regenerated at $140^{\circ}C$. No degradation of Sorb-KM by $SO_2$ added as a pollutant in flue gas was observed during a cycle test.

• 공업화학
• /
• 제27권2호
• /
• pp.123-127
• /
• 2016

메탄올 연료전지는 수소의 제조, 저장 및 운반에 대한 기술적, 재정적 문제로 인해 개발이 촉발되어 에너지밀도가 높은 연료라는 장점으로 포름산 연료전지에 비해 활발히 연구가 진행되어 왔다. 하지만, 포름산 연료전지에 대해서도 전극촉매를 비롯한 핵심부품의 개발 및 연료의 물질전달 특성 등에 대한 연구가 지속적으로 수행되면서 액체 연료전지로써 보다 적합한 연료가 무엇인가에 대해서 실질적인 비교분석이 필요하게 되었다. 본 논문에서는 포름산과 메탄올 연료전지에 대하여 전극촉매, 연료 확산, 크로스오버, 물 관리, 효율, 시스템 구성 측면에서 연구개발 동향을 소개하며 향후 전망에 대해서 고찰하고자 한다.