• Journal of Sensor Science and Technology
• /
• v.8 no.3
• /
• pp.226-231
• /
• 1999

Pyroelectric infrared sensors have been fabricated using P(VDF/TrFE) film with pyroelectric effect. The weight percent and thickness of the poled P(VDF/TrFE) film are 75/25 percent and $25\;{\mu}m$ respectively. For easier fabrication and connection method new top and bottom electrodes design was adapted for human body detecting pyroelectric infrared sensor. An aluminum infrared absorption electrode and bottom electrode were deposited by thermal evaporator. And the device was mounted in TO-5 housing to detect infrared light of $5.5{\sim}14\;{\mu}m$ wavelength. The responsibility, NEP (noise equivalent power) and specific detectivity $D^*$ of the device were $9.62{\times}10^5\;V/W$, $3.95{\times}10^{-7}\;W$ and $5.06{\times}10^5\;cm/W$ under emission energy of $13\;{\mu}W/cm^2$ respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.9
• /
• pp.991-997
• /
• 2011

This paper deals with the basic principles and procedures involved in the steam-chest molding process used for manufacturing expanded polypropylene (EPP) bead foam. Steam-chest molding is an integral process for EPP technology. However, little research has been carried out on the processing conditions for steam-chest molding this process. The characteristics of EPP foam are energy absorption, multiple-impact protection, low weight, structural strength, and durability. In this study, the steam pressure in steam-chest molding was varied to determine the optimum conditions for manufacturing EPP foam. Moreover, annealing was performed after EPP-foam molding to prevent the shrinkage of the steam-molded product. It was possible to verify the mechanism of foam shrinkage by observing the change in weight with time at different annealing temperatures. Moreover, a tensile test and scanning electron microscopy (SEM) analysis were performed to support these experimental results. The dimensional stability of each molded product was investigated at different steam pressures.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.11
• /
• pp.29-35
• /
• 2015

The photo-response characteristics of polysilicon based metal-semiconductor-metal (MSM) photodetector structure, depending on deuterium treatment method, was analyzed by means of the dark-current and the light-current measurements. Al/Ti bilayer was used as a Schottky metal. Our purpose is to incorporate the deuterium atoms into the absorption layer of undoped polysilicon, effectively, for the defect passivation. We have introduced two deuterium treatment methods, a furnace annealing and an ion implantation. In deuterium furnace annealing, deuterium bond was distributed around polysilicon surface where the light current flows. As for the ion implantation, even thought it was a convenient method to locate the deuterium inside the polysilicon film, it creates some damages around polysilicon surface. This deteriorated the photo-response in our photodetector structure.

• Current Optics and Photonics
• /
• v.6 no.6
• /
• pp.521-549
• /
• 2022

Fiber lasers have made remarkable progress over the past three decades, and they now serve far-reaching applications and have even become indispensable in many technology sectors. As there is an insatiable appetite for improved performance, whether relating to enhanced spatio-temporal stability, spectral and noise characteristics, or ever-higher power and brightness, thermal management in these systems becomes increasingly critical. Active convective cooling, such as through flowing water, while highly effective, has its own set of drawbacks and limitations. To overcome them, other synergistic approaches are being adopted that mitigate the sources of heating at their roots, including the quantum defect, concentration quenching, and impurity absorption. Here, these optical methods for thermal management are briefly reviewed and discussed. Their main philosophy is to carefully select both the lasing and pumping wavelengths to moderate, and sometimes reverse, the amount of heat that is generated inside the laser gain medium. First, the sources of heating in fiber lasers are discussed and placed in the context of modern fiber fabrication methods. Next, common methods to measure the temperature of active fibers during laser operation are outlined. Approaches to reduce the quantum defect, including tandem-pumped and short-wavelength lasers, are then reviewed. Finally, newer approaches that annihilate phonons and actually cool the fiber laser below ambient, including radiation-balanced and excitation-balanced fiber lasers, are examined. These solutions, and others yet undetermined, especially the latter, may prove to be a driving force behind a next generation of ultra-high-power and/or ultra-stable laser systems.

• Applied Chemistry for Engineering
• /
• v.33 no.5
• /
• pp.451-458
• /
• 2022

Semiconductor quantum dots (QDs) are optical probes with excellent fluorescence properties. Therefore, they have been applied to various bio-medical imaging techniques and biosensors. Due to the unique optical characteristics of wide absorption and narrow fluorescence energy bands, multiple types of signals can be generated by the combination of fluorescence wavelengths from different QDs, which enables the simultaneous detection of more than two biomarkers. In this review, the advantages and applications of QDs and QD nanobeads (QBs) in multiple biomarker assays were described, and new developments or improvements in multiplexed biomarker detection techniques were summarized. In particular, recent reports were summarized, focusing on the design strategies in immunoassay construction and signal transducing materials for fluorescence-linked immunosorbent assays using QDs and immunochromatographic assays using QBs. New detection platforms will be developed for early diagnosis of diseases and other fields if multiplexed detection technologies of excellent accuracy and sensitivity are combined with artificial intelligence algorithms.

• Composites Research
• /
• v.34 no.2
• /
• pp.115-122
• /
• 2021

SMC(Sheet molding compound) composite is mainly used for forming of vehicle's body. Considering the car accident, it is essential to research the impact behavior and characteristics of materials. It is difficult to identify them because the impact process is completed in a short time. Therefore, the impact damage analysis using FE(finite element) model is required for the impact behavior. The impact damage analysis requires the parameters for the damage model of SMC composite. In this paper, ANN(artificial neural network) technique is applied to obtain the parameters for the damage model of SMC composite. The surrogate model by ANN was constructed with the result in LS-DYNA. By comparing the absorption energy in drop weight test with the result of ANN model, the optimized parameters were obtained. The acquired parameters were validated by comparing the results of the experiment, the FE model and the ANN model.

• Composites Research
• /
• v.20 no.5
• /
• pp.1-6
• /
• 2007

This study was performed to make a comparison on low-velocity impact behavior between graphite/epoxy composite laminate and steel plate. In order to validate the proposed scheme fur the impact behavior of the plate, the Karas's impact model was used. The impact models for this comparative study are the graphite/epoxy composite plate having $[0/90/45/-45/-45/45/90/0]_{8S}$ laminate sequence and the steel plate with a steel ball impactor. The low-velocity impact behaviors for two types of plates were comparatively investigated and performed by considering different impactor velocities and weights respectively. In this investigation, it was found that the composite laminate has impact energy absorption effect due to more flexible behavior than the steel plate, and also it has better characteristics on impact damage and weight.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.3
• /
• pp.208-218
• /
• 2023

Photocatalysts are advanced materials which accelerate the photoreaction by providing ordinary reactions with other pathways. The catalysts have various advantages, such as low-cost, low operating temperature and pressure, and long-term use. They are applied to environmental and energy field, including the air and water purification, water splitting for hydrogen production, sterilization and self-cleaning surfaces. However, commercial photocatalysts only absorb ultraviolet light between 100 and 400 nm of wavelength which comprises only 5% in sunlight due to the wide band gap. In addition, rapid recombination of electron-hole pairs reduces the photocatalytic performance. Recently, studies on blackening photocatalysts by laser, thermal, and plasma treatments have been conducted to enhance the absorption of visible light and photocatalytic activity. The disordered structures could yield mid-gap states and vacancies could cause charge carrier trapping. Herein, liquid phase plasma (LPP) is adopted to synthesize Ag-doped black ZnO for the utilization of visible-light. The physical and chemical characteristics of the synthesized photocatalysts are analyzed by SEM/EDS, XRD, XPS and the optical properties of them are investigated using UV/Vis DRS and PL analyses. Lastly, the photocatalytic activity was evaluated using methylene blue as a pollutant.

• Fisheries and Aquatic Sciences
• /
• v.26 no.9
• /
• pp.535-547
• /
• 2023

Sea cucumbers (Holothuria scabra), also known as beche-de-mer, are highly valued as a luxurious food item and have been utilized as a traditional tonic food in various Asian countries for centuries. The body walls of sea cucumbers are the main edible part, which are primarily composed of glycosaminoglycan (GAG). The rehydration of dried sea cucumber is a crucial step prior to further processing. The aim of this study was to assess the impact of ultrasound-assisted rehydration (UAR) on the quality of dried sea cucumbers. The experiment used four different rehydration methods, including conventional methods at 27℃ (KV27℃) and 15℃ (KV15℃), as well as a combination of ultrasound at 27℃ with conventional at 15℃ (UAR27 + KV15℃) and ultrasound at 15℃ with conventional at 15℃ (UAR15 + KV15℃). Results indicated that the rehydration rate (RR) was significantly affected by both the rehydration method and the temperature used (p < 0.05). UAR27 + KV15℃ was identified as the most effective method in terms of rehydration behavior and quality characteristics of dried sea cucumber, with a RR of 0.58 ± 0.53 gH₂O/hour and reduced rehydration time of up to 28 hours. Moreover, the UAR27 + KV15℃ method demonstrated superior rehydration potential, nutritional value (proximate composition and sulfate content), color, lower energy, and microstructure properties compared to the other methods. The sulfate content and yield of sulfated GAGs were determined to be 89.4 mg/g and 52.8 ㎍/g, respectively. Confirmation of the absorption band of the sulfate group showed the presence of 3-N-acetyl galactosamine at a wavelength of 1,269 cm^-1 and C-O-S at 860 cm^-1. The sea cucumbers treated with UAR exhibited a GAG content approximately 2.9 times higher than those rehydrated with the conventional method. Eventually, the combination of UAR at 27℃ with conventional at 15℃ methods can significantly accelerate the rehydration of sea cucumber without negatively affecting its physical quality properties.

• Structural Engineering and Mechanics
• /
• v.90 no.4
• /
• pp.371-390
• /
• 2024

Investigating the impact of openings on the structural behavior of ferrocement I-beams with two distinct types of reinforcing metallic and non-metallic meshes is the primary goal of the current study. Up until failure, eight 250x200x2200 mm reinforced concrete I-beams were tested under flexural loadings. Depending on the kind of meshes used for reinforcement, the beams are split into two series. A control I-beam with no openings and three beams with one, two, and three openings, respectively, are found in each series. The two series are reinforced with three layers of welded steel meshes and two layers of tensar meshes, respectively, in order to maintain a constant reinforcement ratio. Structural parameters of investigated beams, including first crack, ultimate load, deflection, ductility index, energy absorption, strain characteristics, crack pattern, and failure mode were reported. The number of mesh layers, the volume fraction of reinforcement, and the kind of reinforcing materials are the primary factors that vary. This article presents the outcomes of a study that examined the experimental and numerical performance of ferrocement reinforced concrete I-beams with and without openings reinforced with welded steel mesh and tensar mesh separately. Utilizing ANSYS-16.0 software, nonlinear finite element analysis (NLFEA) was applied to illustrate how composite RC I-beams with openings behaved. In addition, a parametric study is conducted to explore the variables that can most significantly impact the mechanical behavior of the proposed model, such as the number of openings. The FE simulations produced an acceptable degree of experimental value estimation, as demonstrated by the obtained experimental and numerical results. It is also noteworthy to demonstrate that the strength gained by specimens without openings reinforced with tensar meshes was, on average, 22% less than that of specimens reinforced with welded steel meshes. For specimens with openings, this value is become on average 10%.