• The Korean Journal of Ceramics
• /
• v.3 no.2
• /
• pp.139-143
• /
• 1997

The photoluminescence characteristics of the zinc gallate have been investigated as a function of the composition and the firing atmosphere. Two distinct emission bands were observed whose peaks are 360 nm and 430 nm respectively. These emission bands are considered to be from two different emission centers. For $ZnO/Ga_2O_3$=49.3/50.7 or higher, 430 nm band is predominant and for $ZnO/Ga_2O_3$=49.2/50.8 or lower, 360nm band becomes predominant, whereas 430 nm band is almost completely suppressed. The shift of emission peak is though to be due to the change of the cation distribution with the zinc content in the spinel zinc gallate. Also, the emission centers responsible for the 360nm band are considered to be more efficient energy absorbers than the ones for the 430 nm band. Highly efficient green emitting phosphor was obtained by activating Zn-deficient zinc gallate with manganeses.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.62-67
• /
• 2010

Exhausting fossil fuel and increasing concern of air pollution have brought on the change of the focus of developing new vehicles from performance to fuel economy and emission. The gasoline engines adopting the naturally aspirated way use the throttle-body for engine load control. Therefore, its pumping loss increases more than that of the diesel engine, and also mostly operating in a partial load condition has bad influence on fuel economy and emission. In these days, the continuous variable valve timing system and variable induction system are adopted in order to improve fuel consumption and emission. In this study, we optimize the runner length and operate region of variable induction system to simulataneously improve the performance, fuel economy, and emission of gasoline engine with employing GT-Power as a CAE tool for engine analysis and PIAnO as PIDO tool for process integration and design optimization.

• Journal of the Korean Society of Visualization
• /
• v.12 no.3
• /
• pp.9-14
• /
• 2014

Two-photon microscopy (TPM) has been used in plant research as a high-resolution high-depth 3D imaging modality. However, TPM is known to induce photo-damage to the plant in case of long time exposure, and optimal excitation wavelength for plant imaging has not been investigated. Longer excitation wavelength may be appropriate for in vivo two-photon imaging of Arabidopsis thaliana leaves, and effects of longer excitation wavelength were investigated in terms of imaging depth, emission spectrum. Changes of emission spectrum as a function of exposure time at longer excitation wavelength were measured for in vivo longitudinal imaging. Imaging depth was not changed much probably because photon scattering at the cell wall was a limiting factor. Chloroplast emission spectrum showed its intensity peak shift by 20 nm with transition of excitation wavelength from 849 nm or below to 850 nm or higher. Emission spectrum showed different change patterns with excitation wavelengths in longitudinal imaging. Longer excitation wavelengths appeared to interact with chloroplasts differently in comparison with 780 nm excitation wavelength, and may be good for in vivo imaging.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.70-83
• /
• 1997

We made a selection of engine operating conditions in the natural aspiration type diesel engine as load and speed. The effects on the power, smoke emission and cylinder pressure characteristics of these variations in operating conditions were observed experimentally. Also, the smoke emission was predicted by using the Arrhenius equation and empirical equation of the smoke emission was made. At the same time, the correlations, between the combustion and smoke emission characteristic were examined. From the above results, it is clear that to prevent power dropping and to decrease exhaust fume whin the conditions are changed, one should improve the intake system. To do this, the best way is to lower the air-fuel mixing ratio. We found that the parameters of the indicated mean effective pressure, maximum pressure and its location and combustion duration, etc. change the motion in accordance with the conditions described above. Also, we found that the variation of the pressure cycle comes from an amplified variation of the early part of process. From the analysis of comparing combustion and exhaust fume, the exhaust fume is produced at the latter time of combustion and decreased when the combustion ratio is higher. Also, we developed a special formula which can predict the exhaust fume value according to the engine load and speed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.78-83
• /
• 2011

Diesel engine has many advantages such as high thermal efficiency, low fuel consumption and low emission of CO2. However, the diesel engine faced with strengthened emission regulation about NOx and PM. To suppress NOx emission, after-treatment systems such as Lean NOx Trap (LNT), Selective Catalytic Reduction (SCR) are considered as a more practical strategy. This paper investigated the performance of Lean NOx trap of the 4 stroke diesel engine which had a LNT catalyst. Characteristic of exhaust emission at NEDC mode was analyzed. From this result, the effect of nozzle attaching degree, injection quantity and gas flow change on NOx conversion performance was clarified.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.12
• /
• pp.1101-1105
• /
• 2005

We have investigated the optical properties of Erbium (Er)-implanted GaN by photoluminescence (PL). Various doses of Er ion were implanted on GaN epilayers by ion implantation. Visible green emission lines due to inner 4f shell transitions for $Er^{3+}$ were observed from the PL spectrum of Er-implanted GaN. The emission spectrum consists of two narrow green lines at 537 and 558 nm. The green emission lines are identified as $Er^{3+}$ transitions from the $^{5}H_{11/2}$ and $^{4}S_{3/2}$ levels to the $^{4}I_{15/2}$ ground state. The stronger peaks in the case with the dose of $5{\times}10^{14}cm^{-2}$, together with the relatively higher intensity of the $Er^{3+}$ luminescence in the lower doped sample. It implies that some damage remains in the case with the dose of $1{\times}10^{16}cm^{-2}$. The peak positions of emission lines due to inner 4f shell transitions for $Er^{3+}$ do not change with increasing temperature. It indicates that $Er^{3+}$ related emission depends very little on the ambient temperature.

• Journal of Energy Engineering
• /
• v.16 no.1 s.49
• /
• pp.40-45
• /
• 2007

Many countries have been preparing the exercise of UNFCCC (United Nations Framework Convention on Climate Change). If UNFCCC is enforced, considerable changes in generation sector are expected due to the imposed greenhouse gas emission. This paper proposes dispatch scheduling algorithms which incorporate the emission constraints and emission trading. Numerical examples are provided to demonstrate the availability these algorithms.

• Journal of Surface Science and Engineering
• /
• v.38 no.2
• /
• pp.73-78
• /
• 2005

A real-time monitoring of ICP(inductively coupled plasma) assisted magnetron sputtering of MgO was carried out using a QMS(quadrupole mass spectrometer), an OES(optical emission spectrometer), and a digital oscilloscope with a high voltage probe and a current monitor. At the time of ICP ignition, the most distinct impurity was OH emission (308.9 nm) which was dissociated from water molecules. For reactive deposition oxygen was added to Ar and the OH emission intensity was reduced abruptly When the discharge voltage was regulated by a PID controller from 240V(metallic mode) to 120V(oxide mode), the emission intensity from Mg (285.2 nm) changed proportionally to the discharge voltage, but the intensity of Ar I(811.6 nm) was constant. At 100V of discharge voltage, Mg sputtering was almost stopped. Emissions from Ar I(420.1 nm) and Mg I were dropped down to 1/10, but Ar I(811.6 nm) didn't change. And the emission from atomic oxygen (O I, 777.3 nm) was increased to 10 times. These results are compatible with those from QMS study.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.3
• /
• pp.119-124
• /
• 2022

Top emission organic light-emitting diode (TEOLED) is commonly used because of high efficiency and good color purity than bottom - emission organic light-emitting device (BEOLED). Unlike BEOLED, TEOLED contain semitransparent metal cathode and capping layer. Because there are many characteristics to consider just simple thickness change, optimizing organic thickness of TEOLED for microcavity is difficult. So, in this study, we optimized Device capping layer at unoptimized micro-cavity structure TEOLED device. And we compare only capping layer with unoptimized microcavity structure can overcome optimized micro-cavity structure device. We used previous our optimized micro-cavity structure to compare each other. As a result, it has been found that the efficiency can be obtained almost the same or higher only capping layer, which is stacked on top of the device and controls only the thickness and refractive index, without complicated structural calculations. This means that higher efficiencies can be obtained more easily in laboratories with limited organic materials or when optimizing new structures etc.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.06a
• /
• pp.44-45
• /
• 2020

Korea has the fourth highest CO₂ emission among OECD countries in 2018, As of 2019, total greenhouse gas emissions per capita increased by about 98.2% in comparison to 1990. Korea has promised a 37% reduction in greenhouse gas emissions in 2030 from the projected Paris Climate Change Accord. Currently, many countries use the emissions trading system(ETS) for international carbon management. In 2015, ETS has been implemented in Korea, and the importance of calculating CO₂ emissions from construction machinery has increased. So, we require an accurate calculation of the environmental charges through the allocated CERs. Using the CER price and related search keywords, this paper derive about prediction models of CER price and compare and focus on more accurate prediction about CER price. By this method, the budget needed to establish the initial construction process plan can be calculated based on more accurate predicted CER price.