• 한국분말재료학회지
• /
• 제22권2호
• /
• pp.93-99
• /
• 2015

This study investigated the microstructure and tensile properties of a recently made block-type Ni-Cr-Al powder porous material. The block-type powder porous material was made by stacking multiple layers of powder porous thin plates with post-processing such as additional compression and sintering. This study used block-type powder porous materials with two different cell sizes: one with an average cell size of $1,200{\mu}m$ (1200 foam) and the other with an average cell size of $3,000{\mu}m$ (3000 foam). The ${\gamma}$-Ni and ${\gamma}^{\prime}-Ni_3Al$ were identified as the main phases of both materials. However, in the case of the 1,200 foam, a ${\beta}$-NiAl phase was additionally observed. The relative density of each block-type powder porous material, with 1200 foam and 3000 foam, was measured to be 5.78% and 2.93%, respectively. Tensile tests were conducted with strain rates of $10^{-2}{\sim}10^{-4}sec^{-1}$. The test result showed that the tensile strength of the 1,200 foam was 6.0~7.1 MPa, and that of 3,000 foam was 3.0~3.3 MPa. The elongation of the 3,000 foam was higher (~9%) than that (~2%) of the 1,200 foam. This study also discussed the deformation behavior of block-type powder porous material through observations of the fracture surface, with the results above.

• Earthquakes and Structures
• /
• 제2권3호
• /
• pp.233-256
• /
• 2011

This paper investigates the applicability of newly developed Cu-Al-Mn shape memory alloy (SMA) bars to retrofitting of historical masonry constructions by performing quasi-static tests of half-scale brick walls subjected to cyclic out-of-plane flexure. Problems associated with conventional steel reinforcing bars lie in pinching, or degradation of stiffness and strength under cyclic loading, and in their inability to restrain residual deformations in structures during and after intense earthquakes. This paper attempts to resolve the problems by applying newly developed Cu-Al-Mn SMA bars, characterized by large recovery strain, low material cost, and high machinability, as partial replacements for steel bars. Three types of brick wall specimens, unreinforced, steel reinforced, and SMA reinforced specimens are prepared. The specimens are subjected to quasi-static cyclic loading up to rotation angle enough to cause yielding of reinforcing bars. Corresponding nonlinear finite element models are developed to simulate the experimental observations. It was found from the experimental and numerical results that both the steel reinforced and SMA reinforced specimens showed substantial increment in strength and ductility as compared to the unreinforced specimen. The steel reinforced specimen showed pinching and significant residual elongation in reinforcing bars while the SMA reinforced specimen did not. Both the experimental and numerical observations demonstrate the superiority of Cu-Al-Mn SMA bars to conventional steel reinforcing bars in retrofitting historical masonry constructions.

• Journal of Microbiology and Biotechnology
• /
• 제28권9호
• /
• pp.1527-1535
• /
• 2018

Bacterial strain BAS23 was isolated from rice field soil and identified as Bacillus amyloliquefaciens. Based on dual culture method results, the bacterium BAS23 exhibited potent in vitro inhibitory activity on mycelial growth against a broad range of dirty panicle fungal pathogens of rice (Curvularia lunata, Fusarium semitectum and Helminthosporium oryzae). Cell-free culture of BAS23 displayed a significant effect on germ tube elongation and mycelial growth. The highest dry weight reduction (%) values of C. lunata, H. oryzae and F. semitectum were 92.7%, 75.7%, and 68.9%, respectively. Analysis of electrospray ionization-mass spectrometry (ESI-MS) and $^1H$ nuclear magnetic resonance (NMR) spectroscopy revealed that the lipopeptides were iturin A with a C14 side chain (C14 iturinic acid), and a C15 side chain (C15 iturinic acid), which were produced by BAS23 when it was cultured in nutrient broth (NB) for 72 h at $30^{\circ}C$. BAS23, the efficient antagonistic bacterium, also possessed in vitro multiple traits for plant growth promotion and improved rice seedling growth. The results indicated that BAS23 represents a useful option either for biocontrol or as a plant growth-promoting agent.

• Steel and Composite Structures
• /
• 제35권6호
• /
• pp.739-752
• /
• 2020

This paper aims to investigate cyclic plasticity of a new type of high-performance austenitic stainless steel with both high strength and high ductility. The new stainless steel termed as QN1803 has high nitrogen and low nickel, which leads to reduction of cost ranging from 15% to 20%. Another virtue of the new material is its high initial yield strength and tensile strength. Its initial yield strength can be 40% to 50% higher than conventional stainless steel S30408. Elongation of QN1803 can also achieve approximately 50%, which is equivalent to the conventional one. QN1803 also has a corrosion resistance as good as that of S30408. In this paper, both experimental and numerical studies on the new material were conducted. Full-range true stress-true strain relationships under both monotonic and cyclic loading were obtained. A cyclic plasticity model based on the Chaboche model was developed, where a memory surface was newly added and the isotropic hardening rule was modified. A user-defined material subroutine was written, and the proposed cyclic plasticity model can well evaluate full-range hysteretic properties of the material under various loading histories.

• 한국재료학회지
• /
• 제20권7호
• /
• pp.385-391
• /
• 2010

Twinning-induced plasticity (TWIP) steels have attracted great attention due to their excellent mechanical properties of high tensile strength (over 800MPa) and high ductility (over 50%), which result from the high strain hardening due to the mechanical twin formation during plastic deformation. The purpose of this study is to investigate the effect of annealing temperature and alloying elements on the mechanical properties of Fe-18Mn-0.6C TWIP steel. In 1.5%Al TWIP steel with 0.123%Ti content, the average recrystallized grain size was reduced to 2.5 ${\mu}m$ by cold rolling and annealing at $800^{\circ}C$ for 5 min, because of the pinning effect of the fine TiC carbides on grain coarsening. The tensile strength was decreased and the ductility was improved with the increase of the annealing temperature. However, a reversion of hardness and yield strength happened between $750^{\circ}C$ and $800^{\circ}C$ due to TiC and $M_3C$ type precipitation. 0.56% Ni added TWIP steel exhibited relatively lower yield strength, because Ni precipitates were not formed during the annealing process. When this specimen was annealed at $800^{\circ}C$ for 5min, the tensile strength and elongation were revealed at 1096MPa and 61.8%, respectively.

• 한국재료학회지
• /
• 제27권11호
• /
• pp.597-602
• /
• 2017

In this study, an Al-0.7wt%Fe-0.2wt%Mg-0.2wt%Cu-0.02wt%B alloy was designed to fabricate an aluminum alloy for electrical wire having both high strength and high conductivity. The designed Al alloy was processed by casting, extrusion and drawing processes. Especially, the drawing process was done by severe deformation of a rod with an initial diameter of 12 mm into a wire of 2 mm diameter; process was equivalent to an effective strain of 3.58, and the total reduction in area was 97 %. The drawn Al alloy wire was then annealed at various temperatures of 200 to $400^{\circ}C$ for 30 minutes. The mechanical properties, microstructural changes and electrical properties of the annealed specimens were investigated. As the annealing temperature increased, the tensile strength decreased and the elongation increased. Recovery or/and recrystallization occurred as annealing temperature increased, and complete recrystallization occurred at annealing temperatures over $300^{\circ}C$. Electric conductivity increased with increasing temperature up to $250^{\circ}C$, but no significant change was observed above $300^{\circ}C$. It is concluded that, from the viewpoint of the mechanical and electrical properties, the specimen annealed at $350^{\circ}C$ is the most suitable for the wire drawn Al alloy electrical wire.

• 한국재료학회지
• /
• 제2권3호
• /
• pp.191-196
• /
• 1992

Succinonitrile을 첨가한 새로운 에폭시 수지, diglycidyl ether of bisphenol A(DGEBA)/4, 4'-methylene dianiline(MDA)/succinonitrile(SN)계의 역학적 성질을 충격 저항실험과 응력 변형실험을 통하여 곁화반응 특성과 반응기구를 근거로 하여 고찰하였다. DGEBA/MDA계에 각각 다른 succinonitrile의 함량을 포함하는 계를 $80^{\circ}C$에서 1.5시간 동안 경화시킨 후 완전히 경화를 이루기 위하여 $150^{\circ}C$에서 1시간 동안 경화시킨 후 시험한 결과 Succinonitrile의 함량이 증가함에 따라 본 계의 충격강도는 점차적으로 증가하였으나 인장강도는 감소하였다. 그리고 Young률은 거의 일정하게 나타났으며, 신도는 succinonitrile의 함량이 10phr에서 최대값을 보였다. 본 실험으고부터 얻은 결과는 succinonitrile이 첨가됨으로써 주 사슬간의 결합길이가 연장되었기 때문임을 알았고, 적당량의 succinonitrile을 첨가함으로 에폭시 수지의 유연성이 개선됨을 알 수 있었다.

• 미생물학회지
• /
• 제48권2호
• /
• pp.171-174
• /
• 2012

THOC1/Hpr1는 mRNA가 전사되는 동안 mRNP의 포장과 mRNA 방출에 관여하는 진화적으로 잘 보존된 THO 복합체의 한 소단위이다. 분열효모 Schizosaccharomyces pombe에서도 THOC1/Hpr1과 유사한 단백질을 암호화하는 유전자(sphpr1로 명명)를 찾아 그 특성을 조사하였다. 이배체 S. pombe 균주에 하나의 sphpr1 유전자만을 결실시킨 후 4분체 분석을 수행한 결과, 이 유전자는 생장에 필수적이었다. 티아민에 의해 발현이 조절되는 강력한 nmt1 프러모터를 이용하여 sphpr1를 과발현시키더라도 세포의 생장과 mRNA 방출에는 전혀 영향이 없었다. 하지만, sphpr1의 발현을 억제하면 생장이 억제되었으며 poly$(A)^+$ RNA가 핵 안에 축적되었다. 이와 같은 결과들은 sphpr1 유전자가 생장과 mRNA의 핵에서 세포질로의 방출에 관여하고 있음을 시사한다.

• 열처리공학회지
• /
• 제13권1호
• /
• pp.1-9
• /
• 2000

The microstructural characteristics and low temperature tensile properties between $25^{\circ}C$ and $-196^{\circ}C$ for as-welded and age hardened specimen by using Al 5083-H321 for base metal, 5083-5356 and 5083-4043 weldments have been investigated. The hardness of 5083-5356 weldment decreases with aging treatment, whereas the weld region of 5083-4043 weldment shows remarkable increase in hardness after aging due to the precipitation of fine Si particle at the grain boundaries and interiors. Low temperature tensile properties of 5083 AI base metal, 5083-5356 and 5083-4043 weldments appear to be the increment of tensile strengths and elongations at the room temperature and $-196^{\circ}C$, while the decrement of tensile properties around $-50^{\circ}C$ is shown. Through the observation of fine serration to fracture in the stress-strain curve and tensile fractography, the increment of localized deformation leading to promote the neck initiation and the increment of the dimple size cause to decrease in tensile strengths and elongations around $-50^{\circ}C$. For the tensile specimen of the 5083 base metal, 5083-5356 and 5083-4043 weldments, the reason to increase in elongation after solution and aging treatment is the diminishment of fine pit, the resolution of Mg into the matrix and the spheridization of the eutectic Si.

• The Plant Pathology Journal
• /
• 제28권1호
• /
• pp.55-59
• /
• 2012

Northern stem canker caused by $Diaporthe$ $phaseolorum$ var. $caulivora$ ($Dpc$) has become a serious disease in soybean. The objectives of this study were to survey the existence of $Dpc$ on soybean in Korea, and to examine the potential pathogenicity of $Dpc$ in seed decay. One such isolate, SSLP-4, isolated from a field-grown plant of the Korean soybean cultivar Danbaekkong, was identified as $Dpc$, based on its morphological and molecular characteristics by sequences of internal transcribed spacer (ITS), translation elongation factor (TEF) 1-${\alpha}$ and ${\beta}$-tubulin regions, as well as pathogenic analyses. Moreover, morphological and molecular analyses revealed that isolate SSLP-4 was nearly identical to $Dpc$ strains from the United States. Pathogenicity tests on hypocotyls of soybean seedlings and detached leaves resulted in typical symptoms of soybean northern stem canker and inoculation on plants at R5-R7 stage caused seed decay. All results suggest that the $Dpc$ strain SSLP-4 can cause both stem canker and seed decay on soybean. Thus, the SSLP-4 isolate has the potential to contribute greatly to understanding of host plant resistance mechanisms, both at vegetative and reproductive growth stages in soybean.