• Journal of Magnetics
• /
• v.11 no.2
• /
• pp.90-94
• /
• 2006

A finite-element method is used to analyze loss generation and electromagnetic noise absorption characteristics of a coplanar waveguide transmission line integrated with a magnetic thin film. Parameters used in the analysis are the electrical resistivity of the magnetic layer and the thickness of both magnetic and insulating layers. The results indicate that L-C resonance is the main loss mechanism of the electromagnetic noise absorption.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.12
• /
• pp.963-968
• /
• 2018

In this paper, a compact common mode filter using passive elements is designed and fabricated. To design a common mode filter with required frequency response, the equivalent circuits of the common mode filter in differential mode and common mode were analyzed. Compared with the former filter using a ${\lambda}/4$ resonator, the size of the proposed structure was reduced by 60 %. The fabricated common mode filter has a maximum differential mode insertion loss of 1.2 dB and a minimum common mode absorption efficiency of 78.2% in the CMA - bandwidth of 27.5 %.

• Polymer(Korea)
• /
• v.33 no.1
• /
• pp.91-95
• /
• 2009

We fabricated the electromagnetic (EM) noise absorber films for high temperature use by blending a soft magnetic powder with poly(amide imide) (PAI). The EM noise absorber films of PAI/soft magnet composite were prepared by casting the solution of poly(amide amic acid)/soft magnet powder into glass substrate with casting applicator device and then thermal imidization. The obtained films were fully characterized and their physical properties including thermal behavior, thermal stability and mechanical properties were studied. The EM noise absorption ability was also investigated using micro-strip line method. At 1 GHz, the power loss of composite film with 150 ${\mu}m$ thickness was about 25%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.2
• /
• pp.143-148
• /
• 2022

For the purpose of treating health checkups and recovery of patients in a super-aged society, hospitals use devices designed with a reduction circuit of electromagnetic waves associated with the specific absorption rate of electromagnetic waves absorbed by the human body. In this paper, we proposed a filter improvement design method capable of reducing electromagnetic waves. As a result of confirming the validity of the proposed technique through simulation and experimental results, the following result values were obtained. Applying the common-mode (CM) inductor 4 mH to a calibration circuit, noise decreased in a multiband spectrum. Using the differential mode(DM) inductor 40 µH element in the primary calibration circuit, the noise decreased by 15 dB or more in the 3 MHz band spectrum. Also, applying the Admittance Capacitance (Y-Cap) 10 nF element in the secondary calibration circuit resulted in the decrease by more than 30 dB in the band spectrum before 2 MHz. After using a common-mode inductor 4 mH element in the tertiary calibration circuit, it decreased by more than 15 dB in the band spectrum after 2 MHz.

• Journal of the Korean Magnetics Society
• /
• v.23 no.3
• /
• pp.83-88
• /
• 2013

The soft magnetic Fe-Si-Cr flakes with the thickness of about 1 ${\mu}m$ were annealed at 500 and $700^{\circ}C$ for 1 h, and the composite sheets for electromagnetic wave noise absorber available for quasi-microwave band were fabricated by using these annealed flakes and polymer. Further the power loss characteristics of the composite sheets was investigated to clarify the annealing effect on electromagnetic wave absorption properties. The power loss decreased in the frequency range of several GHz when the annealed flakes were used as compared to the sheet using the as-milled FeSiCr alloy flakes. Moreover the sheets using annealed flakes exhibited lower value of real and imaginary part of complex permeability. These inferior electromagnetic wave absorption properties of the composite sheets using annealed alloy flakes were considered to be obtained by the enhanced eddy current effect upon annealing-induced recovery of microstructure and resulted low complex permeability.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.3
• /
• pp.233-238
• /
• 2003

With the growth of high speed circuit, unwanted system noise is increased and multipoint ground is used to reduce this noise. PCB screw ground structure has radiation noise by ground loop between screws. In order to solve this problem, in this paper, we proposed improved PCB ground structure. Proposed structure improves noise absorption by using microwave absorber and conductive copper tape. We measured radiation PCB noise in the range of 1 ㎓ to 3 ㎓ to investigate proposed structure usefulness. From these results, under 2 ㎓ range proposed structure has noise reduction by 2.62 dBuV/m, which compared with screw ground.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2006.06a
• /
• pp.92-92
• /
• 2006

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.6
• /
• pp.509-515
• /
• 2009

In this paper, we analyzed and evaluated noise suppression characteristic of EM wave absorber. We fabricated several absorber samples in different ratios of Sendust and Amorphous with CPE(Chlorinated Ploy-ethylene) as binder and calculated material constants by measured S-parameter. Then, we confirmed that the noise suppression characteristic of EM wave absorbers using microstrip line. A microstrip line with EM wave absorber placed on its top was used to evaluate the conduction noise suppression. As a result, noise suppression effect show different charateristic by changing relative permeability. Therefore, EM wave absorber using Sendust show excellent characteristic. In particular the maximum power absorption over 90 % in 1.7 GHz to over 6 GHz has obtained when composition of Sendust:CPE=80:20wt.%.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.3 s.32
• /
• pp.31-36
• /
• 2004

We charaterized electromagnetic shielding properties of a soft magnetic film using by a ASTM method and 2-port flanged coaxial line method in a RF range and quantitatively analyzed factors for the shielding effectiveness of the soft magnetic film in far field. The shielding effectiveness of the soft magnetic film was dominantly affected by absorption loss not reflection loss in high frequency range of 4-13.5 GHz.

• Korean Journal of Materials Research
• /
• v.29 no.9
• /
• pp.532-541
• /
• 2019

Information and communication technologies are developing rapidly as IC chip size becomes smaller and information processing becomes faster. With this development, digital circuit technology is being widely applied to mobile phones, wireless LANs, mobile terminals, and digital communications, in which high frequency range of GHz is used. In high-density electronic circuits, issues of noise and EMC(Electro-Magnetic Compatibility) arising from cross talk between interconnects or devices should be solved. In this study, sheet-type electromagnetic wave absorbers that cause electromagnetic wave attenuation are fabricated using composites based on soft magnetic metal powder and silicon rubber to solve the problem of electromagnetic waves generated in wireless communication products operating at the frequency range of 2.4 GHz. Sendust(Fe-Si-Al) and carbonyl iron(Fe-C) were used as soft magnetic metals, and their concentrations and sheet thicknesses were varied. Using soft magnetic metal powder, a sheet is fabricated to exhibit maximum electromagnetic attenuation in the target frequency band, and a value of 34.2dB(99.9 % absorption) is achieved at the target frequency.