• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.3 s.94
• /
• pp.293-299
• /
• 2005

This paper introduces a program by which one can perform measurement, analysis, and simulation of electro-magnetic environment which affects on vehicular AV receivers. An integrated system of EM environment collected, GPS(Global Positioning System) informations, and developed simulation program can be an important evaluating tool for the analysis of automobile AV receivers.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.4
• /
• pp.285-289
• /
• 2018

In this paper, we demonstrate electromagnetic wave focusing and rectification based on time reversal as a smart method for far-field wireless power transfer. Time reversal in a complex propagation environment allows for transmission of high peak power pulses by focusing the electromagnetic waves selectively regardless of the receiver position. We demonstrate wave focusing and radio frequency (RF) to direct current (DC) rectification via numerical simulation of a complex propagation environment. The results reveal that time reversal can ensure peak power up to 12 dB greater compared to a narrowband continuous wave signal, thereby enhancing the rectified DC voltage with better efficiency.

• Progress in Superconductivity and Cryogenics
• /
• v.25 no.3
• /
• pp.18-21
• /
• 2023

Pollution of the environment by micro-plastics is now a worldwide problem. Plastics are difficult to decompose and put a great load on the marine environment. Especially a plastic with a size of 5 mm or less is defined as micro-plastic and are carried by ocean currents over long distances, causing global pollution. These are not easily decomposed in the natural environment. In this paper, we aimed to experimentally demonstrate that micro-plastics in seawater can be continuously separated by electromagnetic Archimedes force. Using polyethylene particles of 3 mm in diameter as the separation target, a flow channel was fabricated and separation conditions were investigated by particle trajectory calculations for separation experiments. Based on the calculation results, a solenoid-type superconducting magnet was used as a source of magnetic field to conduct separation experiments of micro-plastics in seawater. Although a high separation rate was assumed in the simulation results, the experimental results did not show any significant improvement in the separation rate due to the electromagnetic Archimedes force. It was found that the gas generated by the electrolytic reaction may have inhibited the migration of the particles.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.11
• /
• pp.1125-1132
• /
• 2011

The purpose of this study is to suggest installation methods of a mobile-communication repeater into a lift system with consideration of EMC. Two approaches, one(Solution 1) is realized with a repeater installed in a lift hoistway and another(Solution 2) installed inside a lift, were proposed. It is confirmed that the Solution 1 is more effective than the Solution 2. And it is suggested that the EIRP of a repeater must be limited to be ${\leq}$-5 dBm by considering electromagnetic immunity level for a lift and safety margin of 20 dB. This limit can provide suitable electromagnetic environment inside a lift with precise power-control mechanism of mobile communication systems. This study could be a good example of Green ICT by improving electromagnetic environment in spite of radio use.

• Journal of electromagnetic engineering and science
• /
• v.4 no.2
• /
• pp.51-55
• /
• 2004

With the progress of the electronics industry and radio communication technology, certain problems, such as electromagnetic interference(EMI), have arisen due to the increased use of electromagnetic(EM) waves. International organizations such as CISPR, FCC, and ANSI have provided the standards for the EM wave environment and for the countermeasure of the electromagnetic compatibility(EMC). EM wave absorbers are used for constructing an anechoic chamber to test and measure EMI and electromagnetic susceptibility(EMS). In this paper, we have designed an one-body EM(electromagnetic) wave ferrite absorber, based on the equivalent material constants method for both normally and obliquely incident waves, whose absorption abilities are superior to that of the conventional ones. The fabricated absorber has a thickness of 27.68 mm and shows an absorption ability over 20 ㏈ in the frequency from 30 MHz to 6 ㎓.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.7 no.1
• /
• pp.1-14
• /
• 1996

The purpose of this paper is to analyze the performance of M-ary PSK communication system according to the types of electromagnetic interference in an impulsive noise environment. We have introduced Gaussian, sinusoidal and rectangular waves as a electromagnetic interference. Using the derived equations, we evaluated the error performance of the BPSK and QPSK system in the presence of electromagnetic interference and impulsive noise. From results, we have obtained that the Gaussian wave produced the most significant performance degradation and that sinusoidal wave produced more performance degradation than rectangular wave. Therefore, without knowing the types of electromagnetic interference, it is best to regard it as Gaussian wave when designing a communication system. In addition, we could found out that the error performance degrades as impulsive noise becomes strong and the error performance can not be improved significantly even the electromagnetic interference becomes weak. Therefore, this describes that the impulsive noise affects dominantly to the performance degradation.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1835-1837
• /
• 2001

The interference of electromagnetic waves in factory is increasing according with development of industrial society and many use of electrical machinery. Electromagnetic wave is defined as the electrical and magnetic field formed by electrical and electronic equipment used in daily lives, which indiscriminatingly affects the human health and operation of machinery. The electromagnetic spectrum ranges from the shorter wavelengths(including gamma and x-rays) to the longer wavelengths(including microwaves and broadcast radio waves). Radiation that is not absorbed or scattered in the atmosphere can reach and affect on the operation of machine. In this study, electromagnetic wave that is interfered to the machine and human is detected in factory, and decrease method of electromagnetic wave interference is studied.

• Journal of Auto-vehicle Safety Association
• /
• v.11 no.4
• /
• pp.50-56
• /
• 2019

Recently, automobile industries have developed ADAS, smart cars, connected cars, automated driving systems, which use a variety of sensor systems - ultrasonics, cameras, lidars and radars - and communication systems. It is necessary to examine the electromagnetic immunity of vehicles equipped with those systems. The electromagnetic immunity tests are carried out in an electromagnetic semi anechoic chamber, which is cut off from the outside. It is difficult to create test environments in which the radar sensor systems of vehicles work properly in the test chamber. In this study, test jigs were designed and tested and as a result they are shown to be effective to create test environments for electromagnetic immunity tests of vehicles equipped with radar sensors. We also proposed additional safety standards for immunity tests of vehicles with radar systems that currently do not exist.

• Journal of the Korean Institute of Navigation
• /
• v.20 no.2
• /
• pp.97-107
• /
• 1996

The method of Electromagnetic Wave Immunity Test is continuously endeavored by IEC and CISPR as international unification, but it has not been established yet. The main reason is why it is difficult to obtain the measurement method and normalization of threshold to find out the complicated parameters for Electromagnetic Wave immunity Test. So far, thus, the Electromagnetic Wave Immunity Test is carried out case by case as the electromagnetic environment, which is set up Electromagnetic Wave Immunity Test. This study has developed an algorithm and measurement software suitable for IEC1000-4 Regulations, where a ready-made Amplifier, and Signal Generator have been used and an interconnecting Interface Board has been constructed for connecting with the other apparatuses, i.e., RF Switch, Power Meter, Field Sensor, Pre-Amp., etc. Therefore, we have achieved the aim to develop an automated software using OOP method and the measurement system.

• Journal of Auto-vehicle Safety Association
• /
• v.12 no.4
• /
• pp.7-12
• /
• 2020

Recently, automobile industries have developed ADAS, smart cars, connected cars, automated driving systems, which use a variety of sensor systems - ultrasonics, cameras, lidars and radars - and communication systems. It is necessary to examine the electromagnetic immunity of vehicles equipped with the sensor systems due to the fact that the normal operation of those systems is very important to the safety of the vehicles. The electromagnetic immunity tests are carried out in an electromagnetic semi anechoic chamber, which is cut off from the outside. It is difficult to create test environments in which the camera sensor systems of vehicles work properly in the test chamber. In this study, test jigs were designed and tested and as a result they are shown to be effective to create test environments for electromagnetic immunity tests of vehicles equipped with camera sensors. We also proposed additional safety standards for immunity tests of vehicles with camera systems that currently do not exist.