• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.2
• /
• pp.60-64
• /
• 2023

In this study, the electrical contact resistance characteristics between graphene and metals, which is one of important factors for the performance of graphene-based devices, were compared. High-quality graphene was synthesized by chemical vapor deposition (CVD) method, and Al, Cu, Ni, and Ti as electrode materials were deposited on the graphene surface with equal thickness of 50 nm. The contact resistances of graphene transferred to SiO₂/Si substrates and metals were measured by the transfer length method (TLM), and the average contact resistances of Al, Cu, Ni, and Ti were found to be 345 Ω, 553 Ω, 110 Ω, and 174 Ω, respectively. It was found that Ni and Ti, which form chemical bonds with graphene, have relatively lower contact resistances compared to Al and Cu, which have physical adsorption properties. The results of this study on the electrical properties between graphene and metals are expected to contribute to the realization of high-performance graphene-based devices including electronics, optoelectronic devices, and sensors by forming low contact resistance with electrodes.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.65 no.1
• /
• pp.53-56
• /
• 2016

Because of the low pollution resistance of the porcelain electrical insulator itself, in this work the anti-pollution performance of insulator was improved by using the functional coating. The ceramic substrates that components were same as the porcelain electrical insulator were used in this experiment. The functional films were coated on the ceramic substrate by using a spray coating method, and then the coated substrate were annealed under different coating condition such as natural curing and annealing temperature of $200^{\circ}C$, $300^{\circ}C$ and $400^{\circ}C$. Then, the contact angles of the coated surfaces were measured and the minimum angle ($8.3^{\circ}$) was obtained at $400^{\circ}C$. The anti-contamination properties were measured, revealing that as the contact angle decreased, the anti-contamination properties improved. The hardness and adhesion were small at the natural curing condition however the excellent mechanical properties were obtained under higher temperature annealing.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.12
• /
• pp.988-991
• /
• 2011

We fabricated a copper phthalocyanine (CuPc) based field-effect transistor with different device structure as a bottom and top contact FET. Also, we used a $SiO_2$ as a gate insulator and analyzed using a current-voltage (I-V) characteristics of the bottom and top contact CuPc FET device. In order to discuss the channel formation, we were observed the capacitance-gate voltage(C-V) characteristics of the bottom and top contact CuPc FET device.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.151-154
• /
• 1998

We have investigated a correlation of the electrical properties of the Pd/Ge/Pd/Ti/Au ohmic contact on n-InGaAs with its microstructures for the high temperature application of compound semiconductor devices. The samples were heat-treated by the rapid thermal annealing at various temperatures. In the contact system, moderately good specific contact resistance was obtained even before annealing because of the low metals-InGaAs barrier height, and better ohmic performances were observed by annealing up to 400˚C. But the ohmic performance was degraded after annealing at 450˚C due to the increment of Pd$_2$Ga$\sub$5/ phases.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1376-1377
• /
• 2006

본 연구에서는 고밀도 플라즈마 식각 시스템을 이용하여 contact hole 식각을 연구하였다. 실험은 공정 변수에 따른 식각 특성을 변화를 SEM 분석을 이용하여 보였으며 공정 압력 증가에 따른 contact hole 패턴의 하부 및 측면이 vertical 하지 못한 현상을 볼 수 있었으며 이는 과도한 라디컬 생성으로 인하여 식각 반응 부산물과 폴리머가 식각 패턴 밖으로 탈착되지 못하여 나타나는 것으로 생각되며 하부 bias 전력을 증가시킴으로써 식각 반응 부산물과 폴리머의 탈착을 도와 식각 프로파일 개선에 영향을 줌을 확인하였다. 또한, 본 장비의 낮은 전자온도 등의 특성으로 인하여 PR의 degradation 현상 등이 나타나지 않았다.

• Korean Journal of Metals and Materials
• /
• v.50 no.10
• /
• pp.785-792
• /
• 2012

A new flip chip structure consisting of interlocking joints locally surrounded by non-conductive adhesive was investigated in order to improve the contact resistance characteristics and prevent the parasitic capacitance increase. The average contact resistance of the interlocking joints was substantially reduced from $135m{\Omega}$ to $79m{\Omega}$ by increasing the flip chip bonding pressure from 85 MPa to 185 MPa. Improvement of the contact resistance characteristics at higher bonding pressure was attributed not only to the increased contact area between Cu chip bumps and Sn pads, but also to the severe plastic deformation of Sn pads caused during formation of the interlocking-joint structure. The parasitic capacitance increase due to the non-conductive adhesive locally surrounding the flip chip joints was estimated to be as small as 12.5%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.167-171
• /
• 2003

We report the material and electrical properties of $CoSi_2$ and $NiSi_2$contacts to n-type 4H-SiC depending on the post-annealing and the metal covering conditions. The Ni and Co silicides are deposited by RF sputtering with Ni/Si/Ni and Co/Si/Co films separately deposited on 4H-SiC substrates. The deposited films are annealed at $800\;^{\circ}C$ in $Ar:H_2$ (9:1) gas ambient. Results of the specific surface resistivity measurements show that the resistivity of the Co-based metal contact was the one order lower than that of the Ni-based contact. The specific contact resistance was measured by a transmission line technique, and the specific contact resistivity of $1.5{\times}10^{-6}\;{\Omega}\;cm^2$ is obtained for Co/Si/Co metal structures after a two-step annealing; at $550\;^{\circ}C$ for 10 min and $800\;^{\circ}C$ for 3min. The physical properties of the contacts were examined by using XRD and AES, and the results indicate that the Co-based metal contacts have better structural stability of silicide phases formed after the high temperature annealing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.321-322
• /
• 2006

The electrical properties of PZT thin film capacitor on TiN/W plug structure were investigated for high density ferroelectric memory devices. In order to enhance the ferroelectric properties of PZT capacitor, the process conditions of bottom electrodes were optimized. The fabricated PZT capacitor on TiN/W plug showed good remanent polarization, leakage current, and contact resistance of TiN/W plug, which were $33\;{\mu}C/cm^2$, $1.2{\times}10^{-6}\;A/cm^2$, and 5.3 ohm/contact, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.404-405
• /
• 2007

Tin-doped indium thin film is outstanding material among transparent Conductive Oxide (TCO) materials. ITO thin films show a low electrical resistance(<$10^{-4}\;[{\Omega}{\cdot}m]$) and high transmittance(>80%) in the visible range. ITO thin films usually have been deposited on the glass substrate. In order to apply flexible display, the substrate should have the ability to bend and be deposited without substrate heat. Also properties of ITO thin film depend on what kind of substrate. In this study, we prepared ITO thin film on the polycarbonate (PC) substrate by using Facing Target Sputtering (FTS) system. Before deposition of ITO thin film, PC substrate took plasma surface treatment. The electrical and surface properties of as-deposited thin films were investigated by Hall Effect measurement, UV/VIS spectrometer and the surface property of substrate is investigated by Contact angle measurement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.243-247
• /
• 2003

The effect of accelerated weathering(UV) on three type of ethylene propylene diene monomer(EPDM) composite used for higher voltage insulator were investigated by weather-emoter. For weatherability of EPDM composite, surface resistance, dielectric breakdown strength, change of contact angle, surface composition were measured according to UV accelerated weathering time. From the resort of the measurement of surface resistivity, contact angle of EPDM composite decreased and showed chalking and cracking phenomenon when UV weathweing time was for 1500 h and 2000 h. The analysis of surface atomic composition indicated that surface aluminiu(Al) content was detected due to chalking phenomenon after 1500 h of UV weathering, Oxygen content of all composite increased due to the oxidation.