• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.506-509
• /
• 2003

In this paper, the $\Phi$-q-n pattern and average discharge power of silicone rubber have investigated effect of inter impurities. It's changed impurities by silicone oil, water and copper. Applied voltage is AC 3, 4, 4.5, 5, 5.5[kV]. And data acquisition time is 10 second(600 cycles). These results suggest that partial discharge(PD) is shower negative polar than positive polar at 3[kV]. Positive polar's PD value increased with increase of applied voltage. The Conductivities expressed same $\Phi$-q-n pattern in positive polar and negative polar at phase region.

• Electrical & Electronic Materials
• /
• v.9 no.4
• /
• pp.379-384
• /
• 1996

The microwave dielectric properties of (I-x)CaTiO$_{3}$-xLaAIO$_{3}$ were investigated. The solid solution of (1-x)CaTiO$_{3}$-xLaAIO$_{3}$ had the perovskite structure in the range of all compositions. The crystal system of (1-x)CaTiO$_{3}$-xLaAIO$_{3}$ was transformed to orthorhombic(x.leq.0.4), psudo-cubic(x=0.5), and rhombohedral (x.geq.0.7) in turn, as the amount of LaAIO$_{3}$ increased. The dielectric constant and temperature coefficient of resonant frequency of solid solution were decreased with the content of LaAIO$_{3}$, whereas, the value of Q . f$_{o}$ was increased. The microwave dielectric material having Q . f$_{o}$ = 32, 500, .epsilon.$_{r}$ = 42, and .tau.$_{f}$ = 5 ppm/.deg. C was obtained from the 0.35CaTiO$_{3}$-0.65LaAIO$_{3}$ composition sintered at 1600.deg. C for 4hrs.hrs.hrs.

• Electrical & Electronic Materials
• /
• v.9 no.9
• /
• pp.900-905
• /
• 1996

We have investigated dielectric properties of low fired ceramics BiNbO$_{4}$ containing 0.05[wt%] V$_{2}$O$_{5}$ and x[wt%l Cr$_{2}$O$_{3}$ (x=0, 0.2, 0.4, 0.8, 1.2). By substituting Cr for Bi, dielectric constant .epsilon.$_{r}$ and quality factor Q.f increased and temperature coefficient of resonant frecquency .tau.$_{f}$ changed to positive value. In the composition of BiNbO$_{4}$+0.05 [Wt%] V$_{2}$O$_{5}$+0.8[wt%]Cr$_{2}$O$_{3}$ sintered at 960[.deg. C], we could obtain microwave dielectric properties of .epsilon.$_{r}$=49, Q.f.simeq.3000[GHz](at 4.8[GHz]), .tau.$_{f}$.simeq.0[ppm/.deg. C]. As the above ceramics can be sintered near 960[.deg. C], it is applicable to multilayer microwave device with Ag conductor.tor.tor.tor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.3
• /
• pp.202-206
• /
• 2003

In this study, modified PbTi $O_3$ ceramics was manufactured to apply for 30MHz SMD type ceramic resonator with the variations of electrode weight. To investigate the effects of electrode weight on resonant characteristics of ceramic resonator using 3$^{rd}$ overtone thickness vibration mode, ceramic wafers for resonator were fabricated by evaporating electrode weights of 0.66, 1.765, 2.32, 3.87$\times$ 10$^{-4}$ g/c $m^2$ with silver, respectively. And then, SMD type ceramic resonators were fabricated with the size of 3.7$\times$3.1mm and electrode radius size of 0.77mm. With increasing electrode weight, resonant resistance was gradually decreased. At the electrode weight of 2.32$\times$10$_{-4}$ g/c $m^2$, mechanical quality factor( $Q_{mt3}$) and dynamic range(D.R) showed the maximum value of 2,152 and 49dB, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.5
• /
• pp.397-403
• /
• 2003

Microwave dielectric properties of (1-x)ZnW $O_4$-xTi $O_2$ ceramic systems were investigated with calcination temperatures and Ti $O_2$ contents. The ZnW $O_4$ ceramic could be suitably sintered at 1075$^{\circ}C$ and showed the dielectric constant of 13.6, quality factor(Q$\times$ $f_{O}$value) of 22,000 and temperature coefficient of resonant frequency($\tau$$_{f}$) of -65$\pm$2ppm/$^{\circ}C$. Increasing the amount of Ti $O_2$ in the range of 0.25 to 0.45 mol, the dielectric constant and $\tau$$_{f}$ increased due to the role of Ti $O_2$ but the quality factor decreased due to the increase of phase boundaries. The 0.7ZnW $O_4$-0.3Ti $O_2$ ceramic showed the dielectric constant of 19.8, qualify factor(Q$\times$ $f_{0}$) of 20,000 and $\tau$$_{f}$ of -3$\pm$1ppm/$^{\circ}C$.>.EX>.>.>.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.282-286
• /
• 2003

We investigated the effects of calcination temperature and sintering additives on the sintering behaviors and microwave dielectric properties of $(Zn_{0.8}Mg_{0.2})TiO_3$. Highly densified samples were obtained at the sintering temperatures below $1000^{\circ}C$ with additions of 0.45 wt.% $Bi_2O_3$ and 0.55 wt.% $V_2O_5$. From the examination of the existing phases and microstructures before and after sintering of $(Zn_{0.8}Mg_{0.2})TiO_3$ system calcined at the various temperatures ranging from $800^{\circ}C$ to $1000^{\circ}C$, it was found that high $Q{\times}f_o$ values were obtained when unreacted or second phases in calcined body were reduced. When calcined at $1000^{\circ}C$ and sintered at $900^{\circ}C$, it consists of hexagonal as a main phase with uniform microstructure and exhibits $Q{\times}f_o$ value of 42,000 GHz and dielectric constant of 22.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.7
• /
• pp.41-47
• /
• 2014

The on-line partial discharge (PD) in stator windings of air-cooled gas turbine (GT) generator (119.2MVA, 13.8kV) is measured and analyzed in this paper. This generator was designed by global vacuum pressure impregnation (VPI). The generator failed two times at top bar (16T) of phase B in the stator slot. Six epoxy-mica capacitors were installed in three phases of GT generator. On-line PD test was performed on GT generator using turbine generator analyzer (TGA). TGA showed that the normalized quantity number (NQN) and the PD magnitude($Q_m$) were high in phase B. Internal discharges were generated in phases A, B and C. The trend analysis of NQN and $Q_m$ value are obtained in order to monitor the insulation condition in GT generator stator windings. Phases A and C were in good condition. But phase B had deteriorated significantly

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.277-278
• /
• 2007

In this study, in order to develop multilayer piezo-actuator, PMN-PNN-PZT ceramics were fabricated using $Li_2CO_3,\;Na_2CO_3$, ZnO as sintering aids and their piezoelectric and dielectric properties were investigated according to the Bi substitution. Bi substitution enhanced electromechanical coupling factor$(k_p)$ and dielectric constant$({\varepsilon}_r)$. However, mechanical quality factor was deteriorated. At the sintering temperature of $870^{\circ}C$ and Bi substitution of 1mol%, density, electromechanical coupling factor$(k_p)$, mechanical quality factor$(Q_m)$, Dielectric constant$({\varepsilon}_r)$ and piezoelectric constant$(d_{33})$ of specimen showed the optimum value of $7.878g/cm^3$, 0.608, 835, 1603 and 397pC/N, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.255-256
• /
• 2007

In the study, in order to develop low temperature sintering ceramics for multilayer piezoelectric actuator, PMN-PNN-PZT ceramics were fabricated using $Na_2CO_3,\;Li_2CO_3$ as sintering aids and their dielectric and piezoelectric properties were investigated according to the variations of $MnO_2$ as additives and sintering aids. At the sintering temperature of $900^{\circ}C$ and 0.1wt% $MnO_2$ as sintering aids, density, electromechanical coupling factor$(k_p)$, mechanical quality factor$(Q_m)$, piezoelectric constant$(d_{33})$, and dielectric constant $({\varepsilon}_r)$ showed the optimum value of $7.87[g/cm^3]$, 0.61, 1131, 1127 and 376, respectively, for multilayer piezoelectric actuator application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.279-282
• /
• 2003

For the millimeter-wave dielectrics, Forsterite-based ceramics were produced. Pure forsterite ceramics($Mg_2SiO_4$) shows porous micro-structure and very low Q*f values, which is not suitable for the dielectrics for the millimeter-wave band. Several sintering aids including $Al_2O_3$, $Li_2CO_3$, $Li_2SiO_4$, were added to the forsterite ceramics in order to produce dense low-loss dielectrics. Among these additives, $Li_2CO_3$ is the most effective sintering aids. Several sub-components including NiO, ZnO, $SnO_2$, $TiO_2$, were added to enhance the microwave dielectric properties. $TiO_2$ is the most effective additive to enhance the dielectric properties at microwave bands. The simultaneous addition of $TiO_2$ and $Li_2CO_3$ increases Q*f value over 170,000, which can be used as dielectrics in millimeter-wave bands.