• Nuclear Engineering and Technology
• /
• 제49권8호
• /
• pp.1748-1751
• /
• 2017

Reduced activation ferritic/martensitic (RAFM) steels are widely applied as structural materials in the nuclear industry. To investigate hydrogen's effect on RAFM steels' elastic properties and the mechanism of that effect, a procedure of first principles simulation combined with experiment was designed. Density functional theory models were established to simulate RAFM steels' elastic status before and after hydrogen's insertion. Also, experiment was designed to measure the Young's modulus of RAFM steel samples with and without hydrogen charging. Both simulation and experiment showed that the solubility of hydrogen in RAFM steels would decrease the Young's modulus. The effect of hydrogen on RAFM steels' Young's modulus was more significant in water-quenched steels than it was in tempering steels. This indicated that defects inside martensite, considered to be hydrogen traps, could decrease the cohesive energy of the matrix and lead to a decrease of the Young's modulus after hydrogen insertion.

• 대한치과교정학회지
• /
• 제21권3호
• /
• pp.563-580
• /
• 1991

The purpose of this study was to investigate and compare the biomechanical properties of orthodontic rubber elastic materials. Latex bands, nylon-covered elastic threads and polyurethane-based elastic modules, delivering $205{\pm}10$ grams force at 30mm stretching state were selected and stored separately in 3 environments-air ($22{\pm}3^{\circ}C$), distilled water ($37{\pm}1^{\circ}C$), or natural saliva ($37{\pm}1^{\circ}C$). And, the amount of remaining force and permanent elongation of each sample were measured on Instron at interval of 1 hour, 6 hours, 12 hours, 24 hours, 1 week, and 2 weeks. So the data derived were analyzed statistically. The results were as follows: 1. Force decay and permanent elongation of all materials increased with time lapsed; elastic module, latex band and nylon-covered elastic thread in that order of the amount of force decay; elastic module, elastic thread, latex band in that order of the amount of permanent elongation. 2. Among environmental conditions, force decay and permanent elongation in natural saliva, most increased, and those in air, least increased. 3. There was a negative correlation between force decay and permanent elongation. 4. Force decay and permanent elongation were most affected by the material itself, time and environments in that order. 5. After 24 hours in saliva, the percentage of remaining force in elastic module was 51.9% (107.37grams); in latex band, 83.2%(172.62grams); in elastic thread, 85.0%(179.25grams). After 2 weeks in saliva, the percentage of remaining force in elastic module was 42.9%(88.75grams); in latex band, 74.5%(154.50grams); in elastic thread, 77.6%(163.75grams).

• 전산구조공학
• /
• 제9권1호
• /
• pp.85-91
• /
• 1996

이 논문에서는 탄성-점탄성 복합재료의 공유면에 존재하는 계면균열에 대한 해석방법을 제시하고 있다. 먼저 탄성-점탄성 대응원리를 이용하여 탄성해석식으로부터 응력확대계수에 대한 식을 유도하였다. 다음으로 시간영역 경계요소법을 이용하여 균열선단에서의 응력을 계산한 다음 응력확대계수의 값을 구하였다. 수치해석의 결과는 본 논문의 정확성과 응용가능성을 보여준다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.596-602
• /
• 2001

Structures in current use are required of weight reduction and strength in many instances. This naturally necessitates frequent applications of composite materials in many areas. Elastic constants are one of key parameters in determining design guidelines for the specific applications of particular materials. In this research two vibratory techniques (acoustic resonance method and impulse technique)are utilized to evaluate elastic constants. Both techniques are suitable for the measurements of dynamic elastic constants. The Impulse technique provides a quick method for the measurement while the acoustic resonance method produces the values of elastic constants which agree better with theoretical values.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.1-4
• /
• 1999

The attenuation coefficients of SiC particle reinforced low-density polyethylene (LDPE) matrix composites were measured by pulse echo method and dynamic elastic measure method with varying the volume fraction of SiC particle ranged from 0% to 40% and the size of SiC particles ranged from 0.8$\mu$m to 48$\mu$m. The SiCp/LDPE composites were fabricated with the melt injection process and the fabricated composites showed almost full density above 99% up to 40vo1% SiCp reinforcements. The attenuation constant of LDPE measured by dynamic elastic constant had same result with that measured by pulse echo method, but the attenuation constant of SiCp/LDPE measured by dynamic elastic constant did not have same result with that measured by pulse echo method.

• Journal of Mechanical Science and Technology
• /
• 제17권12호
• /
• pp.1928-1937
• /
• 2003

Effect of elastic modulus mismatch on the contact crack initiation is investigated to find major parameters in designing desirable surface-coated system. Silicon nitride coated soft materials with various elastic modulus mismatch, E$\_$c//E$\_$s/＝1.06∼356 are prepared for the analysis. Hertzian contact test is conducted for producing contact cracks and the acoustic emission detecting technique for measuring the critical load of crack initiation. The implication is that coating thickness and material strength are controllable parameters to prevent the initiation of contact cracks resulted from the elastic modulus mismatch in the hard ceramic coating layer on the soft materials.

• 소성∙가공
• /
• 제11권7호
• /
• pp.575-580
• /
• 2002

To evaluate elastic and micro-failure properties of MEMS materials, the electro-statically operated test devices were designed and fabricated by micro machining technology. The test structures consist or comb drives for loading and suspending beams in testing. From the analysis of beam displacement based on elastic beam theory, elastic modulus and yield strength of Al film were measured. And, by introducing the micro notch and cyclic loading, the micro-failure was Induced and the micro-fracture toughness of Si film was evaluated. Moreover, the cycles to failure were estimated from the degradation of resonant frequency. Finally, the effects of notch on micro failure were discussed.

• Structural Engineering and Mechanics
• /
• 제58권4호
• /
• pp.613-625
• /
• 2016

Contact interaction of a beam (flexible element) with an elastic half-plane is considered, when a soft inhomogeneous (functionally graded) interlayer is present between them. The beam is bent under the action of a distributed load applied to the surface and a reaction of the elastic interlayer and the half-space. Solution of the contact problem is obtained for different values of thickness and parameters of inhomogeneity of the layer. The interlayer is assumed to be significantly softer than the underlying half-plane; case of 100 times difference in Young's moduli is considered as an example. The influence of the interlayer thickness and gradient of elastic properties on the distribution of the contact stresses under the beam is studied.

• 한국강구조학회 논문집
• /
• 제13권6호
• /
• pp.661-672
• /
• 2001

본 연구는 Arc-length method를 이용한 복합재료 공간 구조물의 대변형 거동의 관찰에 관한 것이다. 비선형 평형경로의 각각의 하중단계에서 자동적으로 Arc-length 크기를 변화시켜 하중-변위 관계곡선을 추적할 수 있도록 하였다. 복합재료 공간 트러스의 점탄성 해석은 quasi-elastic 방법을 사용해 탄성해를 구하였다. Micro Mechanical Materials Modeling 방법을 사용하여 탄성계수를 결정하였고 하중조합에 따른 비선형 하중-변위 곡선을 추적하였다. 본 연구의 효과를 검증하기 위하여 그물형 공간 트러스를 다른 방법의 결과들과 비교하였다.

• 한국재료학회지
• /
• 제14권6호
• /
• pp.436-442
• /
• 2004

Elastic and plastic deformation behaviors of the high purity aluminum and the silica glass were studied using nanoindentation and finite element analysis(FEA) techniques. Berkovich- and cone-type indenters were used for the nanoindentation test. Deformation behaviors and nanoindent profiles of elastic, elastic-plastic or plastic materials were clearly visualized by FEA simulation. Effects of the penetration depth and strain hardening on the deformation behavior were examined. Pile-up and sink-in behaviors were studied by using FEA technique. Degree of pile-up or sink-in was found to be a function of the ratio of elastic modulus to yield strength of materials. FEA was found to be an effective method to study deformation behaviors of materials under nanoindentation, especially in the case when pile-up or sink-in phenomena occurred.