• Electrical & Electronic Materials
• /
• v.9 no.8
• /
• pp.783-788
• /
• 1996

In this paper, the high-$T_c$ , superconductor (HTS) microstrip patch antenna which is directly coupled to a microstrip transmission line is designed and the numerical solution which evaluate near electromagnetic field of HTS antenna is presented. This solution uses the interpolation function with the vector edge triangular element. The advantage of this element is the elimination of spurious solutions attributed to the lack of enforcement of the divergence condition. The results of this method have a good agreement with $TM_10$ mode in HTS microstrip patch antenna and show that the computation of resonant length considering the fringing capacitance effect at radiating edge are proper.

• Proceedings of the KIEE Conference
• /
• 2000.07e
• /
• pp.108-112
• /
• 2000

The electric charge generated by flowing insulation liquid can create hazardous spark in transfer line and receiving tank etc. These electrification has generally been measured by current measurement with a ammeter connected to the receiving tank. This paper reports on the experimental result obtained by this method. As a experimental results: The injected charge value for unit volume increased in the following condition, the edge of the needle electrode was sharp, the number of needle electrode was fewer, the edge of the needle electrode was located close to the inside wall. When the charge density in the charge reducer is constant, electrode current and electrode potential by the charge injection from outside increase with increasing of oil velocity and streaming current. The electrode potential in charge reducer is made maximum value at edge point of reducer inside and minimum value at center line of charge reducer.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.296-300
• /
• 1996

This paper presents 3D position estimation algorithm with the images of 2D vision sensors which issues Red Laser Slit light and recieves the line images. Since the sensor usually measures 2D position of corner(or edge) of a body and the measured point is not fixed in the body, the additional information of the corner(or edge) is used. That is, corner(or edge) line is straight and fixed in the body. For the body which moves in a plane, the Transformation matrix between the body coordinate and the reference coordinate is analytically found. For the 3D motion body, linearization technique and least mean squares method are used.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.2
• /
• pp.152-158
• /
• 2007

Most of experimental visualizations and numerical results on the flow field separated form a leading edge around an unsteady foil show a continuous streakline from the leading edge and large reverse flow between the streakline and the suction surface. However, they have not exactly clarified yet the dynamic behavior of vortices separated from the leading edge because separation around an unsteady foil is very complicated phenomenon due to many parameters. In the present study the flow fields around pitching foils have been visualized by using a Schlieren method with a high speed camera in a wind tunnel at low Reynolds number regions. It has been observed that small vortices are shed discretely from the leading and trailing edge and that they stand in line on the integrated streakline of separation shear layer. By counting vortices in the VTR frames it was clarified that the number of vortex shedding from the leading and trailing edge during one pitching cycle strongly depends on the non-dimensional pitching rate. Futhermore the vortices moving up to the leading edge on the suction surface of the pitching foil are visualized. They play an important role to balance the number of vortex shedding from both edges.

• Journal of Mechanical Science and Technology
• /
• v.14 no.10
• /
• pp.1104-1113
• /
• 2000

This paper proposes an efficient reverse engineering technique for compound surfaces using a boundary detection method. This approach consists in extracting geometric edge information using a vision system, which can be used in order to drastically reduce geometric errors in the vicinity of compound surface boundaries. Through the image-processing technique and the interpolation process, boundaries are reconstructed by either analytic curves (e. g. circle, ellipse, line) or parametric curves (B-spline curve). In other regions, except boundaries, geometric data are acquired on CMM as points inspected using a touch type probe, and then they are interpolated on several surfaces using a B-spline skinning method. Finally, the boundary edge and the skinned surfaces are combined to reconstruct the final compound surface. Through simulations and experimental works, the effectiveness of the proposed method is confirmed.

• Korean Journal of Remote Sensing
• /
• v.19 no.2
• /
• pp.159-169
• /
• 2003

This paper presents a method for automatic 3-d building reconstruction using high resolution aerial imagery. First, by using edge preserving filtering, noise is eliminated and then images are segmented by watershed algorithm, which preserves location of edge pixels. To extract line segments between control points from boundary of each region, we calculate curvature of each pixel on the boundary and then find the control points. Line segment linking is performed according to direction and length of line segments and the location of line segments is adjusted using gradient magnitudes of all pixels of the line segment. Coplanar grouping and pplygonal patch formation are performed per region by selecting 3-d line segments that are matched using epipolar geometry and flight information. The algorithm has been applied to high resolution aerial images and the results show accurate 3D building reconstruction.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.28 no.2
• /
• pp.132-143
• /
• 1992

This paper presents a method in order to calculate the vortex distribution, the streak-line and the time-line around the flat and the cambered otter board in two dimensional flow using the discrete vortex method, and to calculate C sub(L) and C sub(D) of the otter boards varied with the passage of time by the numerical simulation using the Blasu's formula. The results obtained are summarized as follows: 1. Flow pattern around the otter boards calculated by the discrete vortex method was resembled closely that of the visualized photograph. 2. C sub(L) and C sub(D) calculated by the numerical simulation was very similar to the model test. 3. The circulation direction around the otter boards and the action direction of the shearing force can be recognized from the time-line around the otter boards. 4. Flow speed in the back side of the otter boards was faster than that in the front side, and the difference of the flow speed in both side of the cambered otter boards was about 1.3 times greater than that of the flat otter boards. 5. The clockwise vortex was generated in the trailing edge, and the counter-clockwise vortex was generated the leading edge of the otter boards. And they were shown the shape of Karman's vortex varied with the passage of time.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.587-589
• /
• 1995

The safe navigation of a mobile robot requires the recognition of the environment in terms of vision processing. To be guided in the given path, the robot should acquire the information about where the wall and corridor are located. Also unexpected obstacles should be detected as rapid as possible for the safe obstacle avoidance. In the paper, we assume that the mobile robot should be navigated in the flat surface. In terms of this assumption we simplify the correspondence problem by the free navigation surface and matching features in that coordinate system. Basically, the vision processing system adopts line segment of edge as the feature. The extracted line segments of edge out of both image are matched in the free nevigation surface. According to the matching result, each line segment is labeled by the attributes regarding obstacle and free surface and the 3D shape of obstacle is interpreted. This proposed vision processing method is verified in terms of various simulations and experimentation using real images.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.1
• /
• pp.61-69
• /
• 2014

With the extreme ultraviolet (EUV) lithography, the performance limit of chemically amplified resists has recently been extended to 16- and 11-nm nodes. However, the line edge roughness (LER) and the line width roughness (LWR) are not reduced automatically with this performance extension. In this paper, to investigate the impacts of the EUVL mask and the EUVL exposure process on LER, EUVL is modeled using multilayer-thin-film theory for the mask structure and the Monte Carlo (MC) method for the exposure process. Simulation results demonstrate how LERs of the mask transfer to the resist and the exposure process develops the resist LERs.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.2
• /
• pp.369-377
• /
• 2008

Though the Hough transform(HT) is a well-known method for detecting analytical shape represented by a number of free parameters, the basic property of the HT, the one-to-many mapping from an image spare to a Hough space, causes the innate problem, the sensitivity to noise. This basic problem also deteriorates the quality of detected lines and makes the detected line deviated from the real one or generates some bogus, multiple lines where only one real line exists. The size of Hough space also affects the quality of detected lines. In this paper, we analyzed the line distortions in the traditional Hough transform and showed that the distortions are relieved in the edge strength Hough transform(ESHT), which is a modified HT. However the usage of expanded edge and edge strength in ESHT can cause some new line distortions which do not exist in the HT. These new ones can be solved by a proper setting of decreasing and broadening parameter values and the optimal values can be determined only by some pre-determined values. We also illustrated several examples to show the distortion-decreasing property of ESHT.