• 한국지진공학회논문집
• /
• 제28권1호
• /
• pp.11-20
• /
• 2024

The ductility of the system based on the capacity of each structural member constituting the seismic force-resisting system is a significant factor determining the structure's seismic performance. This study aims to provide a procedure to supplement the current seismic design criteria to secure the system's ductility and improve the seismic performance of the steel ordinary moment frames. For the study, a nonlinear analysis was performed on the 9- and 15-story model buildings, and the formation of collapse mechanisms and damage distribution for dynamic loads were analyzed. As a result of analyzing the nonlinear response and damage distribution of the steel ordinary moment frame, local collapse due to the concentration of structural damage was observed in the case where the influence of the higher mode was dominant. In this study, a procedure to improve the seismic performance and avoid inferior dynamic response was proposed by limiting the strength ratio of the column. The proposed procedure effectively improved the seismic performance of steel ordinary moment frames by reducing the probability of local collapse.

• 도시과학
• /
• 제12권2호
• /
• pp.19-30
• /
• 2023

The seismic design of water tanks for fire protection is important to prevent secondary earthquake damages due to fires. In this study, the seismic performance of stainless steel water tanks was evaluated considering both static and dynamic water pressure effects, and the influence of different panel shapes was investigated through numerical analysis. First, a basic water tank model comprised of flat panels was built, and then water pressure distribution including sloshing effects was evaluated. In the result of structural analysis, many panels of the basic water tank exceeded a specified allowable stress for load combinations including earthquake loads. In order to reduce the bending stress of the panel by increasing the moment of inertial of the panel section, alternative shapes of a truncated quadrangular pyramid were developed. Five water tanks with different alternative panel shapes were built and analyzed for the same load combinations. Based on the results of the numerical analysis, a number of effective aspect ratios were selected and modified to increase economic feasibility through additional analysis and structural safety check.

• 한국지진공학회논문집
• /
• 제28권5호
• /
• pp.257-266
• /
• 2024

Due to seismically deficient details, existing reinforced concrete structures have low lateral resistance capacities. Since these building structures suffer an increase in axial loads to the main structural element due to the green retrofit (e.g., energy equipment/device, roof garden) for CO₂ reduction and vertical extension, building capacities are reduced. This paper proposes a machine-learning-based methodology for allowable ranges of axial loading ratio to reinforced concrete columns using simple structural details. The methodology consists of a two-step procedure: (1) a machine-learning-based failure detection model and (2) column damage limits proposed by previous researchers. To demonstrate this proposed method, the existing building structure built in the 1990s was selected, and the allowable range for the target structure was computed for exterior and interior columns.

• 한국지진공학회논문집
• /
• 제10권3호
• /
• pp.57-64
• /
• 2006

현행 약진지역의 내진설계기준은 주로 강진지역에서의 연구결과에 근거하고 있다. 하지만, 약진지역의 경우 지진하중보다는 중력하중이나 풍하중에 의해 구조설계가 지배되므로 구조물의 초과강도가 강진지역의 경우보다 증가하게 된다. 따라서 약진지역에 적합한 내진설계기준을 마련하기 위해서는 강진지역에 적용되는 반응수정계수를 약진지역에 그대로 적용할 수 있는지에 대한 검증이 필요하다. 본 연구에서는 건축구조물에 대한 소성해석을 통해 그 연성도와 초과강도를 산정하고 이에 근거하여 현행 반응수정계수의 적절성 여부를 검토하였다. 강진, 중진, 약진지역 등에서의 초과강도와 연성요구도를 비교하기 위하여 UBC-97에 근거하여 설계된 예제구조물을 선정하여 해석을 수행하였다. 해석결과에 의하면 약진지역의 초과강도가 강진지역보다 크기 때문에 동일한 반응수정계수에 대한 약진지역의 연성요구도는 강진지역에서보다 적게 된다. 따라서 동일한 반응수정계수를 이용하여 설계된 약진지역 구조물의 경우 접합부에서의 소성회전각 요구량을 강진지역의 경우에 비하여 상대적으로 저감시킬 수 있을 것이다.

• 복합신소재구조학회 논문집
• /
• 제6권1호
• /
• pp.14-20
• /
• 2015

In this study, we propose an innovative lateral force distribution building system between tall buildings by utilizing the difference of moment of inertia, as the alternative design for highly integrated city area. Considering a tri-axial symmetric conditions and boundary conditions for the three-dimensional building structure system, a two-dimensional model is composed. In the proposed indeterminate structural model, important design variables are determined for obtaining minimum horizontal deflections, reactions and bending moments at the ground level of the buildings. Regarding a case of the provided two spatial structures connected to 4 buildings, the optimum location of middle located spatial structure is 45% from the top of the building, which minimize the end moments at the bottom of the buildings. In the considered verification examples, reduced drifts at the top location of the building systems are validated against static wind pressure loads and static earthquake loads. The suggested hybrid building system will improve the safety and reliability of the system due to the added internal truss-dome structures in terms of more than 30% reduced drift and vibration through the development of convergence of tall buildings and spatial structures.

• Computers and Concrete
• /
• 제14권2호
• /
• pp.193-209
• /
• 2014

Cyclic test of the columns is of practical relevance to the performance of compression members during an earthquake loading. The strength, ductility and energy absorption capabilities of reinforced concrete (RC) columns subjected to cyclic loading have been estimated by many researchers. These characteristics are not normally inherent in plain concrete but can be achieved by effectively confining columns through transverse reinforcement. An extensive experimental program, in which performance of four RC columns detailed according to provisions of ACI-318-08 was studied in contrast with that of four columns confined by a new proposed technique. This paper presents performance of columns reinforced by standard detailing and cast with 25 and 32 MPa concrete. The experimentally achieved load-displacement hysteresis and backbone curves of two columns are presented. The two approaches which work in conjunction with Response 2000 have been suggested to draw analytical back bone curves of RC columns. The experimental and analytical backbone curves are found in good agreement. This investigation gives a detail insight of the response of RC columns subjected to cyclic loads during their service life. The suggested analytical procedures will be available to the engineers involved in design to appraise the capacity of RC columns.

• 한국전산구조공학회논문집
• /
• 제15권2호
• /
• pp.197-207
• /
• 2002

본 연구에서는 죄굴이 방지된 비부착 가새가 설치된 철골조 건물의 에너지 소산능력과 지진응답에 대하여 연구하였다. 먼저 조화하중을 받는 단자유도계 구조물을 대상으로 변수분석을 수행하고 가새의 최적항복강도를 구하였다. 다자 유도계 골조구조물의 비선형 시간이력 해석을 통하여 다양한 크기와 강도를 가진 가새가 설치된 구조물의 지진응답을 분석하고, 가새의 적당한 층별 분배방법을 찾기 위하여 여러 가지 분배방법을 적용하였다. 해석결과에 따르면 일반적으로 가새의 강성이 증가함에 따라 구조물의 최대변위는 감소하였다. 그러나 구조물의 고유주기 및 하중에 따라 가새의 강성이 커짐에 따라 구조물의 최대 변위와 누적된 손상이 증가하는 것으로 나타났다.

• 대한기계학회논문집A
• /
• 제33권8호
• /
• pp.826-831
• /
• 2009

The piping systems in nuclear power plant are composed of various typed pipes such as straight, elbow pipe, branch and reducer etc. The elbow is connected from straight pipe to another pipes in order to establish the complicated piping system. Elbow is one of very important components considering management of wall thinning degradation. It is however applied by various loads such as system pressure, earthquake, postulated break loading and many transient loads, which provoke simply the internal pressure, bending and torsional stress. In this study, firstly pipes in the secondary system of the nuclear power plant are classified as pipe size and type for selecting the investigating range. Next, a large number of finite element analysis considering the all typed dimensions of commercial pipe has been performed to find out the behavior of TES(twice elastic slop) plastic load of elbows, which is based on evaluation of the structural safety factor. Finally performance based structural safety factor was investigated comparing with maximum allowable load by construction code.

• Steel and Composite Structures
• /
• 제19권6호
• /
• pp.1581-1598
• /
• 2015

A concentric braced steel frame is a very efficient structural system because it requires relatively smaller amount of materials to resist lateral forces. However, primarily developed as a structural system to resist wind loads based on an assumption that the structure behaves elastically, a concentric braced frame possibly experiences the deterioration in energy dissipation after brace buckling and the brittle failure of braces and connections when earthquake loads cause inelastic behavior. Consequently, plastic deformation is concentrated in the floor where brace buckling occurs first, which can lead to the rupture of the structure. This study suggests reinforcing H-shaped braces with non-welded cold-formed stiffeners to restrain flexure and buckling and resist tensile force and compressive force equally. Weak-axis reinforcing members (2 pieces) developed from those suggested in previous studies (4 pieces) were used to reinforce the H-shaped braces in an inverted V-type braced frame. Monotonic loading tests, finite element analysis and cyclic loading tests were carried out to evaluate the structural performance of the reinforced braces and frames. The reinforced braces satisfied the AISC requirement. The reinforcement suggested in this study is expected to prevent the rupture of beams caused by the unbalanced resistance of the braces.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(I)
• /
• pp.111-114
• /
• 2005

While the existing reinforced concrete flat plate(RC flat plate) has a lot of advantages including reduced building height, it has some weak points such as many steel bars and the brittle rupture by punching shear. Compared with the RC flat plate, the post-tensioned flat plate (PT flat plate) has not only the same merits, but it also makes longer span possible and induces slab-column connections to be failed with the ductile behavior rather than with the brittle behavior by means of post-tensioning. However, it is difficult to define the joint behavior of PT flat plate under vertical and lateral loads since there are limit experimental results. For this reason, the experimental study is undertaken to investigate the comparison of behavior of PT flat plate and RC flat plate, and how flat plate(Gravity Load Resisting System) is displaced as lateral loads, like the wind and the earthquake, are occur. The result of this experiment shows that PT flat plate is generally superior to RC flat plate in terms of controlling crack, postponing stiffness deterioration, energy dissipation, etc.