• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.3736-3741
• /
• 2015

Crash impact test is conducted to verify the crashworthiness of fuel tank. Success of the crash impact test means the improvement of survivability of crews by preventing post-crash fire. But, there is a big risk of failure due to huge external load in the crash impact test. The failure of crash impact test can result in serious delay of a entire rotorcraft development because of the design complement and re-production of the test specimens requiring a long-term preparation. Thus, the numerical simulations of the crash impact test has been required at the early design stage to minimize the possibility of trial-and-error in the real test. Present study conducts on the numerical simulation of phase I crash impact test using SPH supported by crash simulation software, LS-DYNA. Test condition of MIL-DTL-27422 is reflected on analysis and material data is acquired by specimen test of fuel cell material. As a result, the crash load on the skin material, overlap area and metal fitting is estimated to confirm the possibility of acquisition of the design load for the determination of the overlap area and adhesive strength.

• Journal of the Mineralogical Society of Korea
• /
• v.23 no.1
• /
• pp.63-71
• /
• 2010

The artificial rains having different pH and weathering simulation test were performed for Gyeongju Namsan granite and dacitic tuff to predict the role of acid rain in the deterioration of stone monuments located in Gyeongju area. The pH 4.0 rain reacted with the fresh granite showed near neutral pH at the early stage due to the hydrolysis of minerals in the rock surface. But the pH changed back to the initial pH in the later stage. On the other hand, the pH 5.6 rain showed the neutral pH for a longer time than the experiment with pH 4.0 rain, reflecting slower reaction of minerals due to the weaker acidity. When the pH 5.6 rain reacted with the weathered granite, the water showed neutral pH longer than the case of the fresh granite. The similar tendencies were observed in the experiment of dacitic tuff, except that the pH 4.0 rain reacted with dacitic tuff took a longer time to go back to the initial pH as compared with the case of granite. These results may due to the differences in mineral composition and texture of two rocks. Dacitic tuff contains more fine-grained or glassy groundmass than granite and is more reactive with weaker acid rain. It was predicted that the weight loss and strength decrease rate of dacitic tuff would be approximatetly twice relative to those of granite in the same experimental environment.

• Journal of Internet Computing and Services
• /
• v.17 no.6
• /
• pp.123-131
• /
• 2016

Process mining in big data environment utilize a number of data were generated from the business process. It generates lots of knowledge and insights regarding implementation and improvement of the process through the event log of the company's enterprise resource planning (ERP) system. In recent years, various research activities engaged with the audit work of company organizations are trying actively by using the maximum strength of the mining process. However, domestic studies on applicable sales auditing system for the process mining are insufficient under big data environment. Therefore, we propose process-mining methods that can be optimally applied to online and traditional auditing system. In advance, we propose continuous monitoring information system that can early detect and prevent the risk under the big data environment by monitoring risk factors in the organizations of enterprise. The scope of the research of this paper is to design a pre-verification system for risk factor via practical examples in sales auditing. Furthermore, realizations of preventive audit, continuous monitoring for high risk, reduction of fraud, and timely action for violation of rules are enhanced by proposed sales auditing system. According to the simulation results, avoidance of financial risks, reduction of audit period, and improvement of audit quality are represented.

• Korean Journal of Social Welfare
• /
• v.51
• /
• pp.157-182
• /
• 2002

This study attempts to identify the changes in social reactions to disabilities in general, and to research the contextual implication of these changes in social work practice in Korea. In the early years after the Industrial Revolution, disability was conceived as social unfitness and it was assumed that the cause and responsibility could be attributed to people with disabilities. But, in the midst and late 20th century, social responsibility for people with disabilities was argued and generally accepted. As the results of these changes, conceptual models explaining disabilities have changed gradually; there has been a transition, so called, from individual model to social model. In a similar vein, WHO has refined the definition and classification of disability. Related to these changes, social welfare service paradigm for people with disabilities has shifted. This paradigm shift can be explained with the perspective of strength approach, empowerment approach, case management and independent living model. In Korea, 1998 Act on welfare for people with disabilities meant that social service for the disabled were categorized with, namely, residential service, community rehabilitation service and vocational rehabilitation service. Recently, the extent of these services has been rapidly broadened. In these situation, this study researched to identify the implications on social work practice in the context of changes in social response, conceptual model, definition and also service paradigm. Such as the followings are enumerated for the implications: disabled person's participation in assessment process, development of assessment tools focusing on social and environmental perspectives, reinforcement of information service helping self-determination, supporting on formal and informal helping network, expanding self-help programs and, finally, a shift from displacement model to support model.

• Journal of the Economic Geographical Society of Korea
• /
• v.22 no.1
• /
• pp.96-109
• /
• 2019

As the role of universities as a civic university contributing to regional development has been emphasized, industry-academic cooperation projects are increasingly focused on quadruple helix interactions of university, government, business and civic society. Drawing upon focus group interviews, we divided place-based industry-academic cooperation projects into four different types and stages of development, according to two indicators of network participation and network strength. Although the proportion of projects that were in the early stages of development was overwhelmingly high, some universities developed a close cooperative system with the local community to enhance the effectiveness of the industry-academic cooperation projects and to implement them in an advanced stage. These findings suggest that the LINC+ project, which has been criticized for its policy effectiveness, will not only contribute to enhancing policy effectiveness through place-based projects but also enhance the role of universities as the main body of regional innovation.

• Journal of the Korean Society of Radiology
• /
• v.13 no.1
• /
• pp.21-29
• /
• 2019

The purpose of this study was to compare the MI using SonoVue along with different machines output and to infer the meaning of the signal difference under the same condition. All of the comparative instruments showed strong signal values at early stage as MI value increased. Over time, the inter-instrumental signal values showed signal attenuation under all conditions except for 10 min of the condition of MI 0.1 of RS85A. E9 and EPIQ7 showed signal degradation due to microbubble collapse over time at all MI values. In the comparison of equipment, the signal strengths of MI 0.1, 0.2, and 0.4 were high in order of EPIQ7, RS85A and E9. In the quantitative analysis, there were statistically significant from the SNR and CNR that were obtained from RS85A and E9 (P-value<0.05). In the quantitative analysis, Epiq7 was statistically significant except for CNR as the MI value was changed In the contrast-enhanced ultrasound, even though MI value was low (MI <0.05), it will be helpful for diagnosis, controlling the MI and scan time because a difference in signal intensity was shown between the three machines.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.2
• /
• pp.54-60
• /
• 2019

Recently, various composite materials for additive manufacturing are interested to expand the application field of 3D printing. 3D printing technique was mainly developed using polymer, and ceramic materials for 3D printing are still in the early stage of research due to the requirement of high solid content and post treatment process. In this study, silica particles with various diameters were surface treated with silane coupling agent, and synthesized as silica composite with photopolymer to apply DLP 3D printing process. DLP is an additive manufacturing technology, which has high accuracy and applicability of various composite materials. The rheological behavior of silica composite was analyzed with various solid contents. After DLP 3D printing was performed using silica composites, the printing accuracy of the 3D printed specimen was less than about 3 % to compare with digital data and he bending strength was 34.3 MPa at the solid content of 80 wt%.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.1
• /
• pp.1-6
• /
• 2021

Concrete structures gradually age due to deterioration of materials or excess loads and environmental factors, and their performance decreases, affecting the usability and safety of structures. Although external tension construction methods are widely used among the reinforcement methods of old bridges, it is insufficient to identify the effects and effects of reinforcement depending on the level of aging. Therefore, in this study, a four-point loading experiment was conducted on the subject with the non-reinforced and external tensioning method to confirm the reinforcement effect of the external tensioning method, assuming the aging of the structure as a reduction in the compressive strength and tensile reinforcement of concrete, to analyze the behavior of the reinforcement and confirm the reinforcement effect. As a result of the experiment, it was difficult to identify the amount of reinforcement in the extreme condition due to early elimination of the anchorage. Therefore, compliance with the regulations on anchor bolts is required when applying the external tension reinforcement method. Crack load and yield load increased depending on whether external tension was reinforced, but before the crack, the stiffness before and after reinforcement was similar, making it difficult to confirm the reinforcement effect.

• Journal of the Korea Convergence Society
• /
• v.13 no.4
• /
• pp.553-560
• /
• 2022

This study was conducted to identify the factors affecting the quality of life of women over 10 years after menopause using data from 2014 to 2019 of the National Health and Nutrition Examination Survey. The subjects were 6,330. The data were analyzed by frequency analysis, t-test and multiple regression analysis using SPSS 25. As a result of the study, the factors affecting the health-related quality of life of women 10 years after menopause were age(F=30.625, p<.001), educational level(F=20.106, p<.001), perceived health status(F=187.925, p<.001, activity limitation(t=201.051, p<.001), arthritis(t=91.131, p<.001), osteoporosis(t=4.709, p=.030), hand grip strength(t=22.151, p<.001), perceived stress(F=32.775, p<.001), and depression(t=20.117, p<.001). The factors accounted for 35.1%(F=110.393, p<.001). In order to improve the quality of life of postmenopausal women, it is necessary to continuously evaluate and improve the factors affecting the quality of life from the early menopause.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.2
• /
• pp.76-83
• /
• 2022

Since the 3D printing mortar is exposed to the atmosphere immediately after printing, moisture is largely evaporated from the surface of the layer. The evaporation of moisture on the surface of the layer greatly causes drying shrinkage and increases the risk of cracking and damage to the structure due to drying shrinkage. This study experimentally evaluated the shrinkage behavior of the initial age using the mortar used for 3D printing. The change in shrinkage was evaluated by comparing the shrinkage of the specimen cured by the sealing method and the atmospheric exposure method. In addition, compared with the case where type 1 cement was used 100%, the shrinkage amount was evaluated when 20% of fly ash was replaced and 10% of silica fume was used. In particular, the effect of three chemical admixtures applied using 3D printing on shrinkage was evaluated experimentally. When fly ash and silica fume were used, the shrinkage amount increased by 60 - 110% compared to the case when type 1 cement was used. The application of viscosity modifiers and shrinkage reducers reduced the shrinkage by at least 18% and at most 70% depending on the curing conditions. The temperature of the specimen temporarily decreased to 15 ℃ at the beginning of curing, and the correlation between the internal temperature of the specimen and the shrinkage behavior was observed.