• Analytical Science and Technology
• /
• v.14 no.6
• /
• pp.471-475
• /
• 2001

Solid phase microextraction(SPME) with $85{\mu}m$-polyacrylate (PA) and $100{\mu}m$-polydimethylsiloxane(PDMS) fibers, coupled to gas chromatography-mass spectrometry was used to determine 1,2-dibromo-3-chloropropane(DBCP) and n-butylbenzene in water. The conditions affecting the SPME process(i.e, extraction time, injection length, injection temperature, desorption time and temperature) were optimized. The linearity of the calibration curve (correlation coefficient, R) was over 0.99 and the limits of detection of the method were between 1.5 and $10.8{\mu}g/L$. Repeatability of the method was between 10.4 and 14.4 %.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1041-1044
• /
• 1992

A solar cell should be operated at the maximum output point on the I-V characteristic curve with constant current and constant voltage in order that the solar energy be fully utilized. According to, in this paper, we describes a controller which can track the maximum power point of a solar arry using current and voltage ripple variation of step up chopper system. The control circuit is desinged such that actual current and voltage are sensed directly from the solar cell array. These two signal are then holded sampling and multiplies by a single chip multiplier.

• Journal of the Korean Mathematical Society
• /
• v.43 no.2
• /
• pp.413-424
• /
• 2006

Let $\Gamma$ be a bounded rotation (BR) curve without cusps in the complex plane $\mathbb{C}$ and let G := int $\Gamma$. We prove that the rate of convergence of the interpolating polynomials based on the zeros of the Faber polynomials $F_n\;for\;\bar G$ to the function of the reflexive Smirnov-Orlicz class $E_M (G)$ is equivalent to the best approximating polynomial rate in $E_M (G)$.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.39-45
• /
• 2012

Currently, the aircraft industry, aircraft parts as well as airframe have been developed in producing, the aircraft parts and fuselages have been produced the product by cutting rather than forging and casting because of the residual stress and stress concentration. In this study, the aircraft is being used in many parts of aluminium alloy 2024 in wire-cut E.D.M. The selected experimental parameters are peak current, no-load voltage, off time and feed rate. It is found that cutting mountain part on surface roughness of the curve 0.3mm than 0.25mm diameter wire electrode is stable in many uniform distribution.

• Journal of The Korean Astronomical Society
• /
• v.11 no.1
• /
• pp.31-36
• /
• 1978

Although Serkowski used a single value K=1.15 in representing all the observed interstellar linear polarization curves by his empirical relation $p({\lambda})/P_{max}$=exp (-K $1n^2({\lambda}_{max}/{\lambda})$), where $p_{max}$ is the maximum polarization at wavelength ${\lambda}_{max}$, we have noticed a meaningful variation in K from observations of 72 stars. By comparing K's with $P_{max}/E_{B-V}\;and\;with\;{\lambda}_{max}$, we have examined how the shape of the polarization curve is related with the degree of grain alignment on one hand, and with grain sizes on the other. We have shown that correlations between K, $P_{max}/E_{B-V}\;and\;with\;{\lambda}_{max}$, are consistent with the idea of Davis-Greenstein mechanism for grain alignment.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.1
• /
• pp.1-9
• /
• 1991

This paper describes a new method of calculating expected energy generation and loss of load probability (L.O.L.P) for electric power system operation and expansion planning. The method represents an equivalent load duration curve (E.L.D.C) as a mixture of cumulants approximation (M.O.N.A). By regarding a load distribution as many normal distributions-rather than one normal distribution-and representing each of them in terms of Gram-Charlier expansion, we could improve the accuracy of results. We developed an algorithm which automatically determines the number of distribution and demarcation points. In modeling of a supply system, we made subsets of generators according to the number of generator outage: since the calculation of each subset's moment needs to be processed rapidly, we further developed specific recursive formulae. The method is applied to the test systems and the results are compared with those of cumulant, M.O.N.A. and Booth-Baleriaux method. It is verified that the M.O.C.A. method is faster and more accure than any other method.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.357-361
• /
• 2016

Si와 InAs 두 가지 채널 물질을 가지고 3가지 수송 방향 <100>, <110>, <111>으로 변화시키며 각각의 Nanowire nMOSFETs을 가지고 ballistic quantum transport simulation을 진행하였다. 각각의 경우에 대해 E-k curve를 구한 다음에 band curvature로 캐리어의 유효질량을 계산하고, 이를 통해 MOSFET의 전류 세기를 결정짓는 DOS와 carrier injection velocity를 구하여 어떤 경우에 가장 높은 ON-current를 흐르게 하는지 확인해 보았다. 하지만 예상과 달리 나노와이어의 직경이 1.4nm으로 매우 작기 때문에 valley-splitting이 일어나 Si<110>의 경우에 가장 작은 캐리어 유효 질량을 갖고 있는 사실을 확인할 수 있었다. 결론적으로 Si<100>의 경우에 trade-off 관계에 있는 DOS와 carrier injection velocity가 6가지 경우 중 최적의 조합을 가짐으로써 가장 높은 ON-current를 흐르게 하였다.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.2
• /
• pp.61-70
• /
• 2000

When clay foundations of embankments are treated with vertical drain, essentially, the strain occurs to vertical direction but the water flow is radial. The initial horizontal permeability and its variation with the vertical compression are key parameters for the choice of the type of drains, their spacing, and affect to the cost of the project. In this study, CRS consolidation test is performed to investigate the anisotropic characteristics of decomposed mudstone soil and direct permeability test is performed on the same specimens. The results of testing show that Ch is larger than Cv. specially, the Cv - $\sigma$v relationship for a soil sample is viewed from three different curve segments corresponding to overconsolidated, transition and normally consolidated states. The anisotropic ratio, rk(kh/kv) is 2.19. Coefficient of permeability in normally consolidated state is related to its void ratio and permeability parameter n. C can be determined from a linear plot of log[k(1+e)] versus log e. The slope, n, of graphs is the same, whereas the vertical intercept, log C, seems to vary somewhat for anisotropic.

• Electrical & Electronic Materials
• /
• v.7 no.3
• /
• pp.231-235
• /
• 1994

The multi-dielectric layer $SiO_2$/$Si_3{N_4}$/$SiO_2$ (ONO) is used to improve charge retention and to scale down the memory device. The nitride layer of MNOS device is oxidize to form ONO system. During the oxidation of the nitride layer, the change of thickness of nitride layer and generation of interface state between nitride layer and top oxide layer occur. In this paper, effects of oxidation of the nitride layer is studied. The decreases of the nitride layer due to oxidation and trapping characteristics of interface state of multi layer dielectric film are investigated through the C-V measurement and F-N tunneling injection experiment using SONOS capacitor structure. Based on the experimental results, carrier trapping model for maximum flatband voltage shift of multi layer dielectric film is proposed and compared with experimental data. As a results of curve fitting, interface trap density between the top oxide and layer is determined as being $5{\times}10^11$~$2{\times}10^12$[$eV^1$$cm^2$].

• Journal of the Korean institute of surface engineering
• /
• v.39 no.1
• /
• pp.35-42
• /
• 2006

In this study, the fatigue properties on the cavitation damage of the flame quenched 8.8Al-bronze (8.8Al-4.5Ni-4.5Fe-Cu) as well as the current nuclear pump impeller materials (8.8Al-bronze, STS316 and SR50A) has been investigated using an ultrasonic vibratory cavitation test. For this the impact loads of cavitation bubbles generated by ultrasonic vibratory device quantitatively evaluated and simultaneously the cavitation erosion experiments have been carried out. The fatigue analysis on the cavitation damage of the materials has been made from the determined impact load distribution (e.g. impact load, bubble count) and erosion parameters (e.g. incubation period, MDPR). According to Miner's law, the determined exponents b of the F-N relation ($F^b$ N = Constant) at the incubation stage (N: the number of fracture cycle) were 5.62, 4.16, 6.25 and 8.1 for the 8.8Al-bronze, flame quenched one, STS316 and SR50A alloys. respectively. At the steady state period, the exponents b of the F-N' curve (N': the number of cycle required for $1{\mu}m$ increment of MDP) were determined as 6.32, 5, 7.14 and 7.76 for the 8.8Al-bronze, flame quenched one, STS316, and SR50A alloys, respectively.