• 대한토목학회논문집
• /
• 제26권3A호
• /
• pp.465-471
• /
• 2006

지진과 같은 동적 반복하중을 받는 강구조물의 이력거동을 구현하기 위해서는 사용된 강재의 정 동적 상태에서의 응력-변형률 관계 및 특성을 고려한 동적반복소성모델이 필요하다. 본 연구에서는 SM490강재의 정 동적 단조 및 반복하중 실험을 수행하여 역학적 특성 및 응력-변형률 관계를 명확히 하였다. 그리고 실험결과에 기초하여 SM490강재의 동적반복소성모델을 제안하였으며 이를 유한변위이론에 기초한 3차원 탄소성 유한요소해석에 적용하였다. 실험시편을 모델링하여 정 동적 단조, 반복 및 변형률속도변화에 따른 3차원 탄소성 유한요소해석을 수행하였으며 이를 실험결과와 비교하였다. 비교를 통하여 본 연구에서 개발한 해석기법이 강부재의 정 동적 변형상태를 정도있게 예측할 수 있음을 검증하였다.

• Steel and Composite Structures
• /
• 제21권4호
• /
• pp.703-753
• /
• 2016

The ratcheting behavior was studied experimentally for Z2CND18.12N elbow piping under cyclic bending and steady internal pressure. Dozens of cyclic plasticity models for structural ratcheting responses simulations were used in the paper. The four models, namely, Bilinear (BKH), Multilinear (MKIN/KINH), Chaboche (CH3), were already available in the ANSYS finite element package. Advanced cyclic plasticity models, such as, modified Chaboche (CH4), Ohno-Wang, modified Ohno-Wang, Abdel Karim-Ohno and modified Abdel Karim-Ohno, were implemented into ANSYS for simulating the experimental responses. Results from the experimental and simulation studies were presented in order to demonstrate the state of structural ratcheting response simulation by these models. None of the models evaluated perform satisfactorily in simulating circumferential strain ratcheting response. Further, improvement in cyclic plasticity modeling and incorporation of material and structural features, like time-dependent, temperature-dependent, non-proportional, dynamic strain aging, residual stresses and anisotropy of materials in the analysis would be essential for advancement of low-cycle fatigue simulations of structures.

• 대한토목학회논문집
• /
• 제43권4호
• /
• pp.469-476
• /
• 2023

반복하중이나 동적하중에 대한 지반의 소성모델은 지반구조물의 비선형 수치해석에 매우 중요하다. 단일 항복면 모델은 반복하중에 대해 선형적 거동을 보이는 반면, 개발된 탄성영역이 없는 J₂-경계면 소성모델은 동일한 물성치로 효과적으로 지반의 비선형성을 모사할 수 있다. 경계면 내부 항복면의 반경을 0으로 수렴시켜 탄성영역이 사라지도록 수식화하고, 소성경화 계수과 팽창률을 이용하여 소성변형 증분을 정의하였다. 개발된 모델의 응력-변형률 증분식을 제시하고, 쌍곡선 모델에 대한 소성경화 계수를 유도하였다. 삼축압축조건과 얕은기초의 반복하중에 대한 비교해석은 개발된 모델의 안정적인 수렴성, 이론식과의 일치성, 그리고 이력경로을 보여 주었다. 또한, 수정된 쌍곡선함수에 대한 소성경화 계수를 제시하여, 1차원 등가선형모델에 부합하는 모델변수 산정법을 제안하여 지반의 다차원 거동을 모델링할 수 있도록 하였다.

• 대한토목학회논문집
• /
• 제26권6A호
• /
• pp.935-941
• /
• 2006

지진과 같은 동적반복하중을 받은 강구조물은 정적하중시와 다른 이력거동을 보인다. 이는 동적변형중인 구조용 강재는 정적상태와 다른 역학적 특성 및 응력-변형률 관계를 보이기 때문이다. 즉, 지진하중을 받는 원형 강기둥과 같은 강구조물의 이력거동을 정확히 예측하기 위해서는 정동적 변형 상태를 가정한 재하속도에 따른 대상구조물 내하력 및 변형의 차이점을 명확히 파악해야 한다. 이에 본 연구에서는 저자에 의해 제안된 SM490강재의 동적 반복소성모델과 이를 적용한 3차원 탄소성 유한요소해석을 이용하여 재하속도와 지름-두께(D/t)비를 변수로한 SM490 원형강기동의 동적해석을 수행하였다. 해석 결과를 통하여 정적에서 동적변형상태로 재하속도 변화에 따른 SM490 원형강기둥의 이력거동 특성 즉, 내하력 및 에너지소산효율의 변화를 명확히 파악하였다.

• Earthquakes and Structures
• /
• 제26권2호
• /
• pp.97-115
• /
• 2024

In this paper, a database consisting of the dynamic shear modulus ratio and damping ratio test data of clay obtained from 406 groups of triaxial tests is constructed with the starting area of Xiong'an New Area as the research background. The aim is to study the nonlinear dynamic properties of clay in this area under cyclic loading. The study found that the effective confining pressure and plasticity index have certain influences on the dynamic shear modulus ratio and damping ratio of clay in this area. Through data analysis, it was found that there was a certain correlation between effective confining pressure and plasticity index and dynamic shear modulus ratio and damping ratio, with fitting degree values greater than 0.1263 for both. However, other physical indices such as the void ratio, natural density, water content and specific gravity have only a small effect on the dynamic shear modulus ratio and the damping ratio, with fitting degree values of less than 0.1 for all of them. This indicates that it is important to consider the influence of effective confining pressure and plasticity index when studying the nonlinear dynamic properties of clays in this area. Based on the above, prediction models for the dynamic shear modulus ratio and damping ratio in this area were constructed separately. The results showed that the model that considered the combined effect of effective confining pressure and plasticity index performed best. The predicted dynamic shear modulus ratio and damping ratio closely matched the actual curves, with approximately 88% of the data falling within ±1.3 times the measured dynamic shear modulus ratio and approximately 85.1% of the data falling within ±1.3 times the measured damping ratio. In contrast, the prediction models that considered only a single influence deviated from the actual values, particularly the model that considered only the plasticity index, which predicted the dynamic shear modulus ratio and the damping ratio within a small distribution range close to the average of the test values. When compared with existing prediction models, it was found that the predicted dynamic shear modulus ratio in this paper was slightly higher, which was due to the overall hardness of the clay in this area, leading to a slightly higher determination of the dynamic shear modulus ratio by the prediction model. Finally, for the dynamic shear modulus ratio and damping ratio of the engineering site in the starting area of Xiong'an New Area, we confirm that the prediction formulas established in this paper have high reliability and provide the applicable range of the prediction model.

• Structural Engineering and Mechanics
• /
• 제69권3호
• /
• pp.243-255
• /
• 2019

Utilization of fiber beam-column element has gained considerable attention in recent years due mainly to its ability to model distributed plasticity over the length of the element through a number of integration points. However, the relatively high sensitivity of the method to modeling parameters as well as material behavior models can pose a significant challenge. Residual drift is one of the seismic demands which is highly sensitive to modeling parameters and material behavior models. Permanent deformations play a prominent role in the post-earthquake evaluation of serviceability of bridges affected by a near-fault ground shaking. In this research, the influence of distributed plasticity modeling parameters using both force-based and displacement-based fiber elements in the prediction of internal forces obtained from the nonlinear static analysis is studied. Having chosen suitable type and size of elements and number of integration points, the authors take the next step by investigating the influence of material behavioral model employed for the prediction of permanent deformations in the nonlinear dynamic analysis. The result shows that the choice of element type and size, number of integration points, modification of cyclic concrete behavior model and reloading strain of concrete significantly influence the fidelity of fiber element method for the prediction of permanent deformations.

• Computers and Concrete
• /
• 제19권3호
• /
• pp.315-323
• /
• 2017

Within the context of continuum mechanics, inelastic behaviours of constitutive responses are usually modelled by using phenomenological approaches. Elasto-plastic damage modelling is extensively used for concrete material in the case of progressive strength and stiffness deterioration. In this paper, a review of the main features of elasto-plastic damage modelling is presented for uniaxial stress-strain relationship. It has been reported in literature that the influence of Alkali-Silica Reaction (ASR) can lead to severe degradations in the modulus of elasticity and compression strength of the concrete material. In order to incorporate the effects of ASR related degradation, in this paper the constitutive model of concrete is based on the coupled damage-plasticity approach where degradation in concrete properties can be captured by adjusting the yield and damage criteria as well as the hardening moduli related parameters within the model. These parameters are adjusted according to results of concrete behaviour from the literature. The effect of ASR on the dynamic behaviour of a beam and a column are illustrated under moving load and cyclic load cases.

• 한국압력기기공학회 논문집
• /
• 제14권2호
• /
• pp.69-76
• /
• 2018

The paper presents preliminary investigation results for the effect of the baseline correction in the acceleration excitation method on finite element seismic analysis results (such as accumulated equivalent plastic strain, equivalent plastic strain considering cyclic plasticity, von Mises effective stress, etc) of nuclear safety Class I components. For investigation, finite element elastic-plastic time-history seismic analysis is performed for a surge line including a pressurizer lower head, a pressurizer surge nozzle, a surge piping, and a hot leg surge nozzle using the Chaboche hardening model. Analysis is performed for various seismic loading methods such as acceleration excitation methods with and without the baseline correction, and a displacement excitation method. Comparing finite element analysis results, the effect of the baseline correction is investigated. As a result of the investigation, it is identified that finite element analysis results using the three methods do not show significant difference.