• 한국도로학회논문집
• /
• 제6권3호
• /
• pp.37-46
• /
• 2004

본 연구는 소성변형을 예측하기 위하여 현재 가장 널리 사용되고 있는 반복주행 (Wheel tracking: WT) 시험을 통해 얻어진 변형량-사이클 곡선의 동적안정도(Dynamic stability : DS)를 정립하기 위한 연구이다. 기존에 반복주행시험을 통해 얻어진 곡선에서 동적안정도를 구하는 방법은 표준화되어 있기는 하지만 불합리한 점이 많아 이를 보다 합리적으로 정립하기 위한 방안을 제시하고자 하였다. 슬래브 $305{\times}305{\times}70mm$의 공시체를 롤러콤팩터로 다짐하여 공극률 약 $4\pm0.5%$로 맞추어 제조하여 반복주행시험을 실시하였다. 기존에 동적안정도를 구하는데 사용하던 방법보다는 본 연구에서 사용한 방법으로 동적안정도를 구하는 것이 침하 깊이와의 상관성을 보다 잘 반영하고, 소성변형 저항성이 좋은 것과 나쁜 것간의 차이가 보다 확실히 나타남을 알 수 있었다. 추후 본 연구에서 개발된 방법으로 계산하여서 동적안정도가 큰 혼합물이 실제 현장에서도 공용성이 우수한지를 추적 조사하는 연구가 뒤따라야 할 것이다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.849-853
• /
• 2002

A specific experimental method, the split Hopkinson pressure bar (SHPB) technique has been widely used to determine the dynamic material properties under the impact compressive loading conditions with strain-rate of the order of 103/s~104/s. In this paper, dynamic deformation behaviors of rubber materials widely used for the isolation of vibration from varying structures under dynamic loading are determined using a Split Hopkinson Pressure Bar technique.

• 한국산학기술학회논문지
• /
• 제18권6호
• /
• pp.263-268
• /
• 2017

상용 마그네슘 합금의 경우, 상온에서 낮은 성형성을 갖기 때문에, 온간 성형 조건 하에서 성형 공정을 수행하는 것이 일반적이다. 마그네슘 합금은 온간 성형 과정 중에 동적 재결정(dynamic recrystallization, DRX)이 발생하여, 초기 결정립 사이즈가 급격하게 작아지며, 내부 전위 밀도가 낮아지게 된다. 이에 따라, 유동 응력 곡선은 세 단계의 복잡한 변형 경화 및 연화 현상을 보이게 된다. 첫 번째 구간에서는 변형률이 증가함에 따라, 가공 경화에 의해 응력이 증가하는 경향을 보이며, 두 번째 구간에서는 동적 재결정 현상에 의한 가공 연화로 응력이 갑작스럽게 감소한다. 세 번째 구간에서는 가공 경화와 가공 연화 사이의 평형에 의해, 응력이 일정하게 나타난다. 본 연구에서는, 성형 온도 $300^{\circ}C$, 변형률 속도는 0.001, 0.1, 1, 10/sec에서 AZ80 합금의 구성 방정식의 18개 변수들을 체계적으로 최적화하며, 유동 곡선의 정확도를 높일 수 있는 방식에 대해 제안하려고 한다. 또한 AZ80외에 AZ61도 추가적으로 최적화여 본 논문에서 제안한 최적화 방식의 성능을 증명하였다.

• 한국소음진동공학회논문집
• /
• 제15권2호
• /
• pp.206-212
• /
• 2005

In many machines handling lightweight and flexible media, such as magnetic tape drives, xerographic copiers and sewing machines, the media must transit an open space. It is important to predict the static and dynamic behavior of the sheets with a high degree of reliability. The nonlinear theory of the dynamic elastica has often been used to a nonlinear dynamic deflection model. In this paper, the governing equation is derived and simulated by the finite difference method. The parametric cubic curve is applied for defining the guide shape. The dynamic contact conditions suggested by Klarbring is used to predict the direction of the flexible media according to the initial velocity and the friction coefficient. The analysis is also compared to the conventional model, showing that after contacting a $45^{\circ}$ wall, the directions of flexible media of two models are different.

• 한국시스템다이내믹스연구
• /
• 제7권2호
• /
• pp.5-20
• /
• 2006

In the advent of ubiquitous information technology (u-IT) as a new emerging horizon of information society, inflated expectations regarding u-IT are growing very fast and higher than those made in the past, which would perhaps result in serious bust after boom and incur tremendous amount of social costs. This paper thus investigates a dynamic mechanism underlying the coevolution between information technology and society by applying systems thinking, particularly, with a focus on the typical phenomenon, 'hype curve' which shows how new technologies initially grow too fast for their own good, crashing from a peak of inflated expectations into a trough of disillusionment before stabilizing on a plateau of productivity. Three basic questions are explored to answer by investigating the mechanisms underlying the 'boom-bust' phenomenon: First, why hype curve appears in the process of technology and society coevolution. Second, how to enhance the stabilization level. Third, when is the right time for the policy intervention.

• 한국도로학회논문집
• /
• 제16권3호
• /
• pp.43-50
• /
• 2014

PURPOSES : The dynamic modulus can be determined by applying the various theories from the Impact Resonance Testing(IRT) Method. The objective of this paper is to determine the best theory to produce the dynamic modulus that has the lowest error as the dynamic modulus data obtained from these theories(Complex Wave equation Resonance Method related to either the transmissibility loss or not, Dynamic Stiffness Resonance Method) compared to the results for dynamic modulus determined by using the Universal Testing Machine. The ultimate object is to develop the predictive model for the dynamic modulus of a Linear Visco-Elastic specimen by using the Complex Wave equation Resonance Method(CWRM) came up for an existing study(S. O. Oyadiji; 1985) and the Optimization. METHODS : At the destructive test which uses the Universal Testing Machine, the dynamic modulus results along with the frequency can be used for determining the sigmoidal master curve function related to the reduced frequency by applying Time-Temperature Superposition Principle. RESULTS : The constant to be solved from Eq. (11) is a value of 14.13. The reduced dynamic modulus obtained from the IRT considering the loss factor related to the impact transmissibility has RMSE of 367.7MPa, MPE of 3.7%. When the predictive dynamic modulus model was applied to determine the master curve, the predictive model has RMSE of 583.5MPa, MPE of 3.5% compared to the destructive test results for the dynamic modulus. CONCLUSIONS : Because we considered that the results obtained from the destructive test had the most highest source credibility in this study, the dynamic modulus data obtained respectively from DSRM, CWRM were compared to the results obtained from the destructive test by using th IRT. At the result, the reduced dynamic modulus derived from DSRM has the most lowest error.

• International Journal of Fluid Machinery and Systems
• /
• 제2권4호
• /
• pp.431-438
• /
• 2009

A Large Eddy Simulation (LES) of the flow in an inducer is carried out under flow rate oscillations. The present study focuses on the dynamic response of the backflow and the unsteady pressure performance to the flow rate fluctuations under non-cavitation conditions. The amplitude of angular momentum fluctuation evaluated by LES is larger than that evaluated by RANS. However, the phase delay of backflow is nearly the same as RANS calculation. The pressure performance curve exhibits a closed curve caused by the inertia effect associated with the flow rate fluctuations. Compared with simplified one dimensional evaluation of the inertia component, the component obtained by LES is smaller. The negative slope of averaged performance curve becomes larger under unsteady conditions. From the conservations of angular momentum and energy, an expression useful for the evaluation of unsteady pressure rise was obtained. The examination of each term of this expression show that the apparent decrease of inertia effects is caused by the response delay of Euler's head and that the increase of negative slope is caused by the delay of inertial term associated with the delay of backflow response. These results are qualitatively confirmed by experiments.

• 한국공작기계학회논문집
• /
• 제13권2호
• /
• pp.25-32
• /
• 2004

This paper presents a new optimization technique of acceleration curve for dynamic structure's movement in which high speed and low vibration are desirable. This technique is based on a genetic algerian with a penalty function for acceleration optimization under the assumption that an initial profile of acceleration curves constitutes the first generation of the genetic algorithm. Especially the penalty function consists of the violation of constraints and the number of violated constraints. The optimized acceleration of the crane through the genetic algorithm and commercial dynamic analysis software has shown to have accurate movement and low vibration compared to the conventional accelerations with jerk discontinuity.

• 소성∙가공
• /
• 제10권1호
• /
• pp.35-41
• /
• 2001

The high temperature deformation behavior of SCM 440 can be characterized by the hot torsion test in the temperature ranges of $900^{\circ}C$~$1100^{\circ}C$ and strain rate ranges of 0.05/sec~5/sec. The aim of this paper is to establish the quantitative equation of the volume fraction of dynamic recrystallization (DRX) as a function of processing variables, such as strain rate ($\varepsilon$), temperature (T), and strain ('$\varepsilon$). During hot deformation, the evolution of microstructure could be analyzed from work hardening rate ($\theta$). For the exact prediction of dynamic softening mechanism the critical strain ($\varepsilon_c$), the strain for maximum softening rate ($\varepsilon^*$ and Avrami' exponent (m') were quantitatively expressed by dimensionless parameter, Z/A, respectively. The transformation-effective strain-temperature curve for DRX could be composed. It was found that the calculated results were agreed with the experimental data for the steel at any deformation conditions.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.55-61
• /
• 2000

Tungsten heavy metal is characterized bi a high density and novel combination of strength and ductility. Among them, 90W-7Ni-3Fe is used for applications, where the high specific weight of the material plays an important role. They are used as counterweights, rotating inertia members, as well as for defense purposes(kinetic energy penetrators, etc.). Because of these applications, it is essential to detemine the dynamic characteristics of tungsten alloy. In this paper, Explicit FEM(finite element method) is employed to investigate the dynamic characteristics of tungsten heavy metal under base of stress wave propagation theory for SHPB, and the model of specimen is divided into two parts to understand the phenomenon that stress wave penetrates through each tungsten base and matrix. This simulation results were compared to experimental one and through this program the dynamic stress-strain curve of tungsten heavy metal can be obtained using quasi static stress-strain curve of pure tungsten and matrix.