• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.1
• /
• pp.39-49
• /
• 1999

Monolayer thick fluorocarbon films were characterized by the contact angle measurements. The contact angles of three different liquids, water, formamide and diiodomethane were measured on spun coated, vapor phased deposited films and Teflon surface. The highest contact angle over $130^{\circ}$was observed on fluorocarbon films deposited on Al substrates while the lowest angles below $70^{\circ}$deposited on oxide. The surface energies were calculated based on Lewis acid /base theory. The surface energies of Teflon and spin coated FC films were calculated to have 18 and 8.4 dynes /cm, respectively. Higher energies of 31 to .35 dynes /cm were calculated on vapor phase deposited films on silicon and oxide. However vapor phase deposited films on aluminum only showed a large Lewis base energy term. It might be explained by the surface roughness and heterogeneity as observed by dynamic contact angles and AFM measurements.

• International Journal of Concrete Structures and Materials
• /
• v.11 no.2
• /
• pp.315-325
• /
• 2017

The purpose of the paper is to determine the influence of two widely used steel fibers and polypropylene fibers on the sulphate crystallization resistance, freeze-thaw resistance and surface wettability of ultra-high performance concrete (UHPC). Tests were carried out on cubes and cylinders of plain UHPC and fiber reinforced UHPC with varying contents ranging from 0.25 to 1% steel fibers and/or polypropylene fibers. Extensive data from the salt resistance test, frost resistance test, dynamic modulus of elasticity test before and after freezing-thawing, as well as the contact angle test were recorded and analyzed. Fiber hybridization relatively increased the resistance to salt crystallization and freeze-thaw resistance of UHPC in comparison with a single type of fiber in UHPC at the same fiber volume fraction. The experimental results indicate that hybrid fibers can significantly improve the adhesion properties and reduce the wettability of the UHPC surface.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2390-2395
• /
• 2008

The water droplet motion in an air flow microchannel with pores through which water emerges is studied numerically by solving the equations governing the conservation of mass and momentum. The gas-liquid interface is tracked by a level set method which is based on a sharp-interface representation for accurately imposing the matching conditions at the interface and is modified to implement the contact angle conditions on the wall and pores. The numerical results show that the droplet growth and detachment pattern depend significantly on the contact angle and inlet air velocity. Also, the dynamic interaction between the droplets growing on multiple pores is investigated. The pore arrangement subject to droplet merging is found to be not effective for water removal.

• Journal of the Korean Society for Railway
• /
• v.15 no.2
• /
• pp.162-171
• /
• 2012

In this study, a new dynamic interaction analysis method for tilting trains and curved track is presented. Three dimensional lumped parameter vehicle elements are used to model tilting train, and the proposed analysis technique can simulate driving direction change of vehicle, the effect of track cant, wheel-rail contact angle, and tilting angle of tilting trains, etc. The proposed method passed several basic verification tests, and it is expected that the suggested method is applicable for practical problems.

• Journal of ILASS-Korea
• /
• v.20 no.3
• /
• pp.181-186
• /
• 2015

This study presents the dynamic wetting characteristics of an impact droplet on hole-patterned textured surfaces. The flat surfaces were manufactured by a drilling machine to generate the micro-order holes, leading to make the surface hydrophobic. Other flat surfaces were fabricated by the anodizing technique to make hydrophilic texture surfaces with a nanometer order. For hydrophilic and hydrophobic textured surfaces with similar texture area fractions, the impinging droplet experiments were conducted and compared with flat surface cases. As results, an anodized textured surface decreases apparent equilibrium contact angle and increases contact diameters, because of increase in contact area and surface energy. This is attributed to more penetration inside holes from larger capillary pressure on nanometer-order holes. On the other hand, temporal evolution of the contact diameter is smaller for the hydrophobic textured surface from less penetration on the micro-order holes.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1994-1999
• /
• 2003

This paper discusses dynamic characteristics of motion of a pair of multi-degrees of freedom robot fingers executing grasp of a rigid object and controlling its orientation with the aid of rolling contacts. In particular, the discussions are focused on a problem of gain-tuning of sensory feedback signals proposed from the viewpoint of sensorymotor coordination, which consist of a feedforward term, a feedback term for controlling rotational moment of the object, and another term for controlling its rotational angle. It is found through computer simulations of the overall fingersobject dynamics subject to rolling contact constraints that some dynamic characteristics of torque-angular velocity relation may play an important role likely as reported by experimental results in muscle physiology and therefore selection of damping gains in angular velocity feedback depending on the guess of object mass is crucial. Finally, a guidance of gain-tuning in each feedback term is suggested and its validity is discussed by various computer simulations.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1446-1454
• /
• 1990

A systematic method of design modification to reduce the influence of impact from multiple clearances in a planar four bar mechanism is developed. For this purpose, an optimization method is used with the objective function which is the linear sum of the Earles and Wu criteria for every joints with clearances. One coil spring is attached to a joint of limited range of revolution to reduce the undesirable dynamic effects due to clearances at joints. The stiffness of the coil spring and its pre-loading angle are chosen as design variables. A numerical example is taken for a four bar mechanism. The initial and modified mechanisms are compared using a clearance mechanism analysis technic to see the difference in dynamic effects due to contact loss. It is found that the modified mechanism produces much more smooth joint contact forces than the original design.

• The Korean Journal of Rheology
• /
• v.11 no.1
• /
• pp.34-43
• /
• 1999

Flow-induced voids during resin impregnation and poor fiber wetting have known to be highly detrimental to the performance of composite parts manufactured by resin transfer molding(RTM) process. In this study, in order to overcome these serious problems encountered in RTM, the effects of surface modification by using silane coupling agent as a surface modifier on the flow characteristics, the wetting between resin and fiber, and void content were investigated. For the experiments of microscopic flow visualization and curing in a beam mold, glass fiber mats having plain weaving structure and epoxy resin were used. Modifying the fiber surface was found to result in a significant decrease of dynamic contact angle between resin and fiber and increase of wicking rate. Therefore, it was confirmed that the surface modification employed in this study could improve the wettability of reinforcing fibers as well as micro flow behavior. In addition, It was revealed that high temperature and low penetration rate of the resin are more favorable processing conditions to reduce the dynamic contact angle. However, surface modified fiber mat was found to have lower permeability than the unmodified one, which may be explained in terms of the decrease of contact time between resin and fiber owing to improvement of wetting. It was also exhibited that surface modification had a significant influence on void formation in RTM process, resulting in a decrease of overall void content due to the improvement of wetting in cured composite parts.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.83-90
• /
• 2010

The windshield wiper consists of 4 parts: a blade, an arm, a linkage and a motor. The wiper blade makes contact with the windshield and is designed to be operated normally at an angle of 30~50 degrees to the front glass. If the contact pressure between the wiper blade and windshield surface is too high, noise and wear of the rubber will result. On the other hand, if the contact pressure is too low, the performance will do badly, since foreign substances such as dust and stains will not be removed well. The pressure and friction of the wiper blade has a great influence on its effectiveness in cleaning the front window. This is due to the contact of the rubber with the window. This paper presents the dynamic analysis method to estimate the performance of the flat type blade of the wiper system. The blade has a nonlinear characteristic since the rubber is an incompressible hyper-elastic and visco-elastic material. Thus, Structural dynamic analysis using a complex contact model for the blade is performed to find the characteristics of the blade. The flexible multi-body dynamic model is verified by the comparison between test and analysis result. Also, the optimization using the central composite design table is performed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.42-48
• /
• 1997

The dynamic response of symmetric cross-ply and angle-ply composite laminated plates under impact loads is investigated using a higher order shear deformation theory. A modified Hertz law is used to predict the impact loads and a four node finite element is used to model the plate. By using a higher order shear deformation theory, the out-of-plane shear stresses, which can be a crucial factor in the failure of composite plates, are determined with significant accuracy. The results compared with previous investigations showed good agreement. The effect of ply sequence and ply angle on the contact force is also studied.