• 한국세라믹학회지
• /
• 제52권4호
• /
• pp.294-298
• /
• 2015

Blocking layers with nano carbon blacks (NCBs) were prepared by adding 0.0 ~ 0.5 wt% NCBs to the $TiO_2$ blocking layer. Then, dye sensitized solar cells (DSSCs) were fabricated with a $0.45cm^2$ active area. TEM and micro-Raman spectroscopy were used to characterize the microstructure and phases of the NCBs, respectively. Optical microscopy and AFM were used to analyze the microstructure of the $TiO_2$ blocking layer with NCBs. UV-VIS-NIS spectroscopy was used to determine the band gap of the $TiO_2$ blocking layer with NCBs. A solar simulator and potentiostat were used to determine the photovoltaic properties and impedance of DSSCs with NCBs. The energy conversion efficiency (ECE) increased from 3.53 to 6.20 % when the NCB content increased from 0.0 to 0.3 wt%. This indicates that the effective surface area and electron mobility increased in the $TiO_2$ blocking layer with NCBs. However, the ECE decreased when the NCB content was increased to over 0.4 wt%. This change occurred because the effective electron transport area decreased with the addition of excessive NCBs to the $TiO_2$ blocking layer. The results of this study suggest that the ECE of DSSCs can be enhanced by adding the appropriate amount of NCBs to the $TiO_2$ blocking layer.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.335-338
• /
• 2007

Cost effectiveness is an important parameter for producing DSSCs as compared to the widely used conventional silicon based solar cells. A fluorine-doped tin oxide (FTO) substrate coated with a catalytic amount of platinum is used as counter electrode in dye-sensitized solar cell. Carbonaceous materials are quite attractive to replace platinum due to their high electronic conductivity, corrosion resistance towards $I_{2}$, good catalytic effect and low cost. In this paper, the unit DSSCs with Pt and CNT as a counter electrode were connected in series-parallel externally, then the current-voltage curves were investigated to find out the connection characteristics of the DSSC with CNT counter electrode. The connection characteristics of the DSSC with CNT counter electrode is superior to that of the DSSC with Pt counter electrode. And a parallel connection of the DSSC with CNT counter electrode has higher efficiency than a series connection of that.

• Bulletin of the Korean Chemical Society
• /
• 제32권8호
• /
• pp.2633-2636
• /
• 2011

A new type of ionic liquid based on N-(3-aminepropyl)imidazolium iodide, called IIQAI, which consists of imidazolium and quaternary ammonium salt, and APII-(hydroxyethyl, propyl, hexyl) were synthesized and used as ionic liquid in dye-sensitized solar cells. APII-hexyl is solid, whereas IIQAI, APII-(hydroxyethyl, propyl) are viscous liquids. The synthesized ionic liquid showed relative thermal stability compared to the commercial ionic liquid of DMII. Among them, IIQAI was more stable than the other ionic liquid because of the two salt groups. APII-hydroxyethyl, which contains two hydroxyl groups, showed low viscosity with good flow. New types of ionic liquids were examined by $^1H$-NMR spectroscopy, thermo gravimetric analysis (TGA). IIQAI enabled a solar energy conversion efficiency of 6.3%, which is slightly higher than that of the referenced (DMII, 6.2%).

• 대한금속재료학회지
• /
• 제50권3호
• /
• pp.243-247
• /
• 2012

A ruthenium (Ru) catalytic layer and a conventional Pt layer were assessed as counter electrodes (CE) for dye sensitized solar cells (DSSCs). Ru films with different thicknesses of 34, 46, and 90 nm were deposited by atomic layer deposition (ALD). Pt layers with the same thicknesses were prepared by sputtering. $0.45cm^2$ DSSCs were prepared and their properties were characterized by FE-SEM, cyclic voltammetry (CV), impedance spectroscopy (EIS), and current-voltage (I-V). FE-SEM revealed that the crystallized Ru films and Pt films had been deposited quite conformally. CV showed that the catalytic activity of Pt was much greater than that of Ru. In addition, although the catalytic activity of Pt did not depend on the thickness, that of Ru showed an increase with increasing thickness. Impedance analysis revealed high charge transfer resistance at the Ru interface and a decrease with increasing Ru thickness, whereas Pt showed low resistance with no thickness dependence. Despite the relatively small catalytic activity of Ru, the I-V result revealed the average energy conversion efficiency of Ru and Pt to be 2.98% and 6.57%, respectively. These results suggest that Ru can be used as counter electrodes in DSSCs due to its extremely low temperature process compatibility.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.441-441
• /
• 2009

Dye-sensitized solar cells (DSSCs) have been widely investigated as a next-generation solar cell because of their simple fabrication process and low coats. The cells use a porous nanocrystalline TiO2 matrix coated with a sensitizer dye that acts as the light-harvesting element. The photo-exited dye injects electrons into the $TiO_2$ particles, and the oxide dye reacts with I- in the electrolyte in regenerative cycle that is completed by the reduction of $I_3^-$ at a platinum-coated counter electrode. Since $TiO_2$ porous film plays a key role in the enhancement of photoelectric conversion efficiency of DSSC, many scientists focus their researches on it. Especially, a high light-to-electricity conversion efficiency results from particle size and crystallographic phase, film porosity, surface structure, charge and surface area to volume ratio of porous $TiO_2$ electrodes, on which the dye can be sufficiently adsorbed. Effective treatment of the photoanode is important to improve DSSC performance. In this paper, to obtain properties of surface and dispersion as nitric acid treated $TiO_2$ photoelectrode was investigate. The photovoltaic characteristics of DSSCs based the electrode fabricated by nitric acid pre-treatment $TiO_2$ materials gave better performances on both of short circuit current density and open circuit voltage. We compare dispersion of $TiO_2$ nanoparticles before and after nitric acid treatment and measured Ti oxidized state from XPS. Low charge transfer resistance was obtained in nitric acid treated sample than that of untreated sample. The dye-sensitized solar cell based on the nitric acid treatment had open-circuit voltage of 0.71 V, a short-circuit current of 15.2 mAcm-2 and an energy conversion efficiency of 6.6 % under light intensity of $100\;mWcm^{-2}$. About 14 % increases in efficiency obtained when the $TiO_2$ electrode was treated by nitric acid.

• Journal of Electrochemical Science and Technology
• /
• 제1권2호
• /
• pp.81-84
• /
• 2010

In dye-sensitized solar cells (DSSCs), the back transfer of photo-generated electrons from FTO glass to triiodide ions in an electrolyte is an important loss mechanism, which leads to low cell efficiency. Recently, this back electron transfer was greatly suppressed by the introduction of a compact $TiO_2$ blocking layer, which was prepared by the treatment of $TiCl_4$ solution. In the present work, more detailed $TiCl_4$ treated surface conditions on FTO substrate were investigated and DSSC performances were correlated with the surface morphology as well as dark current behavior.

• 한국수소및신에너지학회논문집
• /
• 제28권4호
• /
• pp.419-425
• /
• 2017

In this study, an efficient dye-sensitive solar cells (DSSC) was developed after post-treatment of ZnO on $TiO_2$ photoelectrode. The $TiO_2$ electrode with ZnO post treatment was prepared with Titanium isoporopoxide in Zinc Nitrate Hexahydrate aqueous solution by incineration for 30 min at $450^{\circ}C$. The ZnO-post treated $TiO_2$ electrode showed strong dispersion force between particles in relation to the control $TiO_2$, referring high specific surface area and dye-adsorption rate. Proper addition of ZnO enhanced electron mobility and reduced internal resistance and electron recombination. Light conversion efficiency of DSSCs containing the ZnO-posttreated $TiO_2$ electrode increased 35.4% when compared to the DSSCs using $TiO_2$ electrode. It is similar to the DSSCs with $TiCl_4$ post treatment $TiO_2$ electrode. Increasing of light conversion efficiency was due to high specific surface area and dispersion force, and low dye-adsorption rate and electron recombination. Taken together, ZnO may be used as posttreatment of photoelectrode and replaced $TiCl_4$ that has high toxicity and causticity.

• Bulletin of the Korean Chemical Society
• /
• 제34권3호
• /
• pp.831-836
• /
• 2013

Platinized counter electrode is common in most of the dye sensitized solar cell (DSSC) researches because of its high catalytic activity and corrosion stability against iodine in the electrolyte. Platinum (Pt) film coating on fluorine doped tin oxide (FTO) glass surface by using alcoholic solution of hexachloroplatinic acid ($H_2PtCl_6$), paste containing Pt precursors or sputtering are widely used techniques. This paper presents a novel application of Pt ink containing nanoparticles for making platinized counter electrode for DSSC. The characteristics of Pt films coated on FTO glass surface by different chemical methods were compared along with the performance parameters of the DSSCs made by using the films as counter electrodes. The samples coated with Pt inks were sintered at $300^{\circ}C$ for 30 minutes whereas Pt-film and Pt-paste were sintered at $400^{\circ}C$ for 30 minutes. The Pt ink diluted in n-hexane was found to a promising candidate for the preparation of platinized counter electrode. The ink may also be applicable for DSSC on flexible substrates after optimization its sintering temperature.

• Bulletin of the Korean Chemical Society
• /
• 제30권10호
• /
• pp.2329-2337
• /
• 2009

Three heteroleptic ruthenium sensitizers, Ru(L)($L^1)(NCS)_2$ [L = 4,4'-dicarboxylic acid-2,2'-bipyridine, Ru-T1: $L^1$ = (E)-2-(4'-methyl-2,2'-bipyridin-4-yl)-3-(thiophen-2-yl)acrylonitrile, Ru-T2: $L^2$ = (E)-3-(5'-hexyl-2,2'-bithiophen-5- yl)-2-(4'-methyl-2,2'-bipyridin-4-yl)acrylonitrile, and Ru-T3: $L^3$ = (E)-3-(5"-hexyl-2,2':5',2"-terthiophen-5-yl)-2- (4'-methyl-2,2'-bipyridin-4-yl)acrylonitrile)], were synthesized and used as photosensitizers in nanocrystalline dyesensitized solar cells (DSSCs). The introduction of the 3-(5-hexyloligothiophen-5-yl)acrylonitrile group increased the conjugation length of the bipyridine donor ligand and thus improved their molar absorption coefficient and light harvesting efficiency. DSSCs with the configuration of Sn$O_2$: F/Ti$O_2$/ruthenium dye/liquid electrolyte/Pt devices were fabricated using these Ru-$T1{\sim}T3$ as a photosensitizers. Among the devices, the DSSCs composed of Ru-T2 exhibited highest power conversion efficiency (PCE) of 2.84% under AM 1.5 G illumination (100 mW/$cm^2$).

• 대한금속재료학회지
• /
• 제50권2호
• /
• pp.159-163
• /
• 2012

A TCO-less ruthenium (Ru) catalytic layer on glass substrate instead of conventional Ru/TCO/ glass substrate was assessed as counter electrode (CE) material in dye sensitized solar cells (DSSCs) by examining the effect of the Ru thickness on the DSSC performance. Ru films with different thicknesses (34, 46, 69, and 90 nm) were deposited by atomic layer deposition (ALD) on glass substrates to replace both existing catalyst and electrode layer. In order to make our comparison, we also prepared an Ru catalytic layer by a similar method on FTO/glass substrate. Finally, we prepared the $0.45cm^2$ DSSC device the properties of the DSSCs were examined by cyclic voltammetry (CV), impedance spectroscopy (EIS), and current-voltage (I-V) method. CV measurements revealed an increase in catalytic activity with increasing film thickness. The charge transfer resistance at the interface between the electrolyte and Rudecreased with increasing Ru thickness. I-V results showed that the energy conversion efficiency increased up to 1.96%. Our results imply that TCO-less Ru/glass might perform as both catalyst and electrode layer when it is used in counter electrodes in DSSCs.