• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.5
• /
• pp.415-429
• /
• 2011

In this study, a single-phase quasi Z-source AC-AC converters with a series connection of the output terminals is proposed. The proposed system has configuration that the input terminals of two quasi Z-source AC-AC converters are connected in parallel and its output terminals are connected in series. The out of phase mode and in phase mode of the proposed system are presented. To verify the validity of the proposed converter, a DSP controlled hardware was made and PSIM simulation was executed. As a result, controlling the duty ratio of the converter, the desired buck-boost output voltages could be generated. For each modes, as compared with the single converter operation, the proposed converter could enhance the efficiency and input power factor according to different loads. Also, in case of the out of phase mode under the constant load, the efficiency and input power factor of the proposed system are increased 10[%], 35[%] respectively in compared with the single converter. And, the output voltage is constantly controlled in dynamic state in case while the load is suddenly changed.

• Journal of Power Electronics
• /
• v.19 no.6
• /
• pp.1366-1379
• /
• 2019

High-gain DC/DC converters have become one of the key technologies for the grid-connected operation of new energy power generation, and its research provides a significant impetus for the rapid development of new energy power generation. Inspired by the transformer effect and the ripple-suppressed ability of a coupled inductor, a double-coupled inductor high gain DC/DC converter with a ripple absorption circuit is proposed in this paper. By integrating the diode-capacitor voltage multiplying unit into the quadratic Boost converter and assembling the independent inductor into the magnetic core of structure coupled inductors, the adjustable range of the voltage gain can be effectively extended and the limit on duty ratio can be avoided. In addition, the volume of the magnetic element can be reduced. Very small ripples of input current can be obtained by the ripple absorption circuit, which is composed of an auxiliary inductor and a capacitor. The leakage inductance loss can be recovered to the load in a switching period, and the switching-off voltage spikes caused by leakage inductance can be suppressed by absorption in the diode-capacitor voltage multiplying unit. On the basis of the theoretical analysis, the feasibility of the proposed converter is verified by test results obtained by simulations and an experimental prototype.

• Journal of Power Electronics
• /
• v.19 no.5
• /
• pp.1108-1121
• /
• 2019

The non-inverting buck-boost converter (NIBB) is a step-up and step-down DC-DC converter suitable for wide-input-voltage-range applications. However, when the input voltage is close to the output voltage, the NIBB needs to operate in the buck-boost mode, causing a significant efficiency reduction since all four switches operates in the PWM mode. Considering both the current stress limitation and the efficiency optimization, a novel design methodology for the optimal phase-shift modulation of a NIBB in the buck-boost mode is proposed in this paper. Since the four switches in the NIBB form two bridges, the shifted phase between the two bridges can serve as an extra degree of freedom for performance optimization. With general phase-shift modulation, the analytic current expressions for every duty ratio, shifted phase and input voltage are derived. Then with the two key factors in the NIBB, the converter efficiency and the switch current stress, taken into account, an objective function with constraints is derived. By optimizing the derived objective function over the full input voltage range, an offline design methodology for the optimal modulation scheme is proposed for efficiency optimization on the premise of current stress limitation. Finally, the designed optimal modulation scheme is implemented on a DSPs and the design methodology is verified with experimental results on a 300V-1.5kW NIBB prototype.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.190-200
• /
• 2019

The flyback converter, which can be regarded as a nonlinear time-varying system, has complex dynamics and nonlinear behaviors. These phenomena can affect the stability of the converter. To simplify the modeling process and retain the information of the output capacitor branch, a special sampled-data model of a peak current-mode (PCM) controlled flyback converter is established in this paper. Based on this, its dynamic behaviors are analyzed, which provides guidance for designing the circuit parameters of the converter. With the critical stability boundary equation derived by a Jacobian matrix, the stable operation range with a varied output capacitor, proportional coefficient of error the amplifier, input voltage, reference voltage and slope of the compensation ramp of a PCM controlled flyback converter are investigated in detail. Research results show that the duty ratio should be less than 0.5 for a PCM controlled flyback converter without ramp compensation to operate in a stable state. The stability regions in the parameter space between the output capacitor and the proportional coefficient of the error amplifier are enlarged by increasing the input voltage or by decreasing the reference voltage. Furthermore, the ramp compensation also can extend to the stable region. Finally, time-domain simulations and experimental results are presented to verify the theoretical analysis results.

• The Korea Journal of Herbology
• /
• v.24 no.4
• /
• pp.63-67
• /
• 2009

Objectives : Quality control for imported medicinal herbs is duty for regulation, however to the best of our knowledge there has been no report regarding quality control of imported ones. Therefore, this study investigated the data of imported ones for monitoring quality issue. Methods : These data are categorized according to item, the amount of import, country, inspection item, suitability, and incongruity reason based on the 248 results performed by KIOM. Results : China is the number one country for import with the value of 73%. Inspected medicinal herbs were 139 species, among them Poria is ranked as top for requested number and the amount of import. The amount of import is similar between high ranking 20 species and low ranking 119 ones, showing high ranking ones are major. The incongruity ratio was 7.7% from the total number of inspected items, the reason for incongruity was excess of tolerable amount of Cd residue. Conclusions : From the data, it is effective way to focus on high ranking herbs for evaluating imported herbs for quality control. The study of mechanism on Cd accumulation and its decrease is essential for environmental matter. And identification and storage for mixed used and easily decomposable herbs are remained for further study. Our study might be small step for showing guideline for proper quality control.

• Nuclear Engineering and Technology
• /
• v.55 no.2
• /
• pp.452-459
• /
• 2023

The core power control is an important issue for the study of dynamic characteristics in China initiative accelerator driven subcritical system (CiADS), which has direct impact on the control strategy and safety analysis process. The CiADS is an experimental facility that is only controlled by the proton beam intensity without considering the control rods in the current engineering design stage. In order to get the optimized operation scheme with the stable and reliable features, the variation of beam intensity using the continuous and periodic control approaches has been adopted, and the change of collimator and the adjusting of duty ratio have been proposed in the power control process. Considering the neutronics and the thermal-hydraulics characteristics in CiADS, the physical model for the core power control has been established by means of the point reactor kinetics method and the lumped parameter method. Moreover, the multi-inputs single-output (MISO) logical structure for the power control process has been constructed using proportional integral derivative (PID) controller, and the meta-heuristic algorithm has been employed to obtain the global optimized parameters for the stable running mode without producing large perturbations. Finally, the verification and validation of the control method have been tested based on the reference scenarios in considering the disturbances of spallation neutron source and inlet temperature respectively, where all the numerical results reveal that the optimization method has satisfactory performance in the CiADS core power control scenarios.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.2
• /
• pp.21-31
• /
• 2010

This paper presents a design of PLL and SSCG for reducing the EMI effect at the electronic machinery and tools for DisplayPort application. This system is composed of the essential element of PLL and Charge-Pump2 and Reference Clock Divider to implement the SSCG operation. In this paper, 270MHz/162MHz dual-mode PLL that can provide 10-phase and 1.35GHz/810MHz PLL that can reduce the jitter are designed for 2.7Gbps/162Gbps DisplayPort application. The jitter can be reduced drastically by combining 270MHz/162MHz PLL with 2-stage 5 to 1 serializer and 1.35GHz PLL with 2 to 1 serializer. This paper propose the frequency divider topology which can share the divider between modes and guarantee the 50% duty ratio. And, the output current mismatch can be reduced by using the proposed charge-pump topology. It is implemented using 0.13 um CMOS process and die areas of 270MHz/162MHz PLL and 1.35GHz/810MHz PLL are $650um\;{\times}\;500um$ and $600um\;{\times}\;500um$, respectively. The VCO tuning range of 270 MHz/162 MHz PLL is 330 MHz and the phase noise is -114 dBc/Hz at 1 MHz offset. The measured SSCG down spread amplitude is 0.5% and modulation frequency is 31kHz. The total power consumption is 48mW.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.151-151
• /
• 2012

A new plasma process, i.e., the combination of PIII&D and HIPIMS, was developed to implant non-gaseous ions into materials surface. HIPIMS is a special mode of operation of pulsed-DC magnetron sputtering, in which high pulsed DC power exceeding ~1 kW/$cm^2$ of its peak power density is applied to the magnetron sputtering target while the average power density remains manageable to the cooling capacity of the equipment by using a very small duty ratio of operation. Due to the high peak power density applied to the sputtering target, a large fraction of sputtered atoms is ionized. If the negative high voltage pulse applied to the sample stage in PIII&D system is synchronized with the pulsed plasma of sputtered target material by HIPIMS operation, the implantation of non-gaseous ions can be successfully accomplished. The new process has great advantage that thin film deposition and non-gaseous ion implantation along with in-situ film modification can be achieved in a single plasma chamber. Even broader application areas of PIII&D technology are believed to be envisaged by this newly developed process. In one application of non-gaseous plasma immersion ion implantation, Ge ions were implanted into SiO2 thin film at 60 keV to form Ge quantum dots embedded in SiO2 dielectric material. The crystalline Ge quantum dots were shown to be 5~10 nm in size and well dispersed in SiO2 matrix. In another application, Ag ions were implanted into SS-304 substrate to endow the anti-microbial property of the surface. Yet another bio-application was Mg ion implantation into Ti to improve its osteointegration property for bone implants. Catalyst is another promising application field of nongaseous plasma immersion ion implantation because ion implantation results in atomically dispersed catalytic agents with high surface to volume ratio. Pt ions were implanted into the surface of Al2O3 catalytic supporter and its H2 generation property was measured for DME reforming catalyst. In this talk, a newly developed, non-gaseous plasma immersion ion implantation technique and its applications would be shown and discussed.

• Korean Security Journal
• /
• no.9
• /
• pp.27-68
• /
• 2005

Recently, because credit card crime using a personal credit information is increasing, professionalizing, and spreading the area, the loss occurring from credit card crime is enormous and is difficult to arrest and punish the criminals. At past, crime from forging and counterfeiting the credit card was originated by minority criminals, but at present, the types and appearance of credit card crime is very different to contrasting past crime. The numbers of people using credit card in the middle of 1990's was increasing and barometer of living conditions was evaluated by the number having credit card, therefore this bad phenomenon occurring from credit card crime was affected by abnormal consumption patterns. There is no need emphasizing the importance of personal credit card in this credit society. so, because credit card crime using personal credit card information has a bad effect, and brings the economic loss and harms to individuals, credit card company, and members joining credit card. Credit card crime using personal credit card information means the conduct using another people's credit card information(card number, expiring duration, secret number) that detected by unlawful means. And crime using dishonest means from another people's credit information is called a crime profiting money-making and a crime lending an illegal advance by making false documents. A findings on countermeasures of this study are as follows: Firstly, Diverting user's mind, improving the art of printing, and legitimating password from payment gateway was suggested. Secondly, Complementing input of password, disseminating the system of key-board protection, and promoting legitimations of immediate notification duty was suggested. Thirdly, Certificating the electronic certificates as a personal certificates, assuring the recognition by sense organ of organism, and lessening the ratio of crime occurrence, and restricting the ratio of the credit card crime was suggested.

• Journal of Preventive Medicine and Public Health
• /
• v.29 no.2 s.53
• /
• pp.347-357
• /
• 1996

Although occupational low back pain accounts for $20\sim40%$ of all occupational illness and injury, there are limited numbers of studies regarding the effectiveness of back school program. The objective of this study was to evaluate the economic benefit of back school program for early return to work of occupational low back pain patients in the current occupational injury compensation and management system. The cost-benefit analysis in this study was conducted to evaluate the relative magnitude of benefit to cost. The total cost was estimated by calculating the value of components in back school program according to governmental budget protocol. The back school program was consisted of three major approaches, pain center, work-hardening program and funcional restoration program and each of components had various facilities and experts. The total amount of cost was estimated as 250,866,220 won per year. The most promising type of back school program were quite intensive (a 3 to 5-week stay in a specialized center), therefore, if we adopted the 5-week stay course, 10 courses could be held in a year. Following to the medical act, 20 patients per doctor could participate in a each course, ie, total 200 patients in a year. As a result, we could estimate the cost of 1,254,331 won a patient. We estimated the benefit by using data of a few local labor offices about average medical treatment beneficiary and off-duty beneficiary of 46 occupational low back pain patients in 1994. Ullman and Larsson (1977) mentioned that the group of chronic low back pain patients who participated in back school program needed less time to recover by 48.4% of beneficiary duration. And in the trying to estimate the benefit, we asked 10 rehabilitation board certificate doctors about reduction proportion of treatment cost by introducing back school program. The answered reduction proportions were in the range of $30\sim45%$, average 39%. As a final result, we could see that the introduction of back school program in treatment of chronic occupational low back pain patients could produce the benefit to cost ratio as 3.90 and 6.28. And we could conclude that the introduction of back school program was beneficial to current occupational injury compensation and management system.