• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.3
• /
• pp.179-187
• /
• 1987

Dual converter using diode bridge and 6-thyristor is discussed and the characteristics of this converter depending on their switching mode is revealed. The switching modes of converter operation are identified on both ac and dc sides. The circuit has the ability to accept or deliver DC current without change of nominal DC voltage magnitude or polarity and has the capability not only to instantaneously change from motoring to generating and vice versa, but to operate cycloconverter.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1838-1840
• /
• 2001

A dual probe laser Doppler vibrometer (LDV) that has one laser source and provides two independent object beams has been developed for the first time. An electronic circuit that converts light signal to electronic signal has been also developed using digital phase locked loop(DPLL). It was found that this types of dual probe LDV can be used in differential mode and self-vibration compensation mode.

• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.151-152
• /
• 2013

본 논문에서는 DAB(Dual Active Bridge)로 구성된 양방향 절연형 DC-DC 컨버터의 제어 기법인 SPS(Single Phase Shift)와 DPS(Dual Phase Shift)를 양방향 OBC(On-Board Charger)의 충전 및 방전모드에 적용한다. 그리고 각 모드의 입출력 조건에 따라 전력 반도체 소자에서 발생되는 손실을 PSIM 시뮬레이션과 수학적 분석을 통해 예측하고, 이를 비교 분석한다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.4
• /
• pp.477-486
• /
• 1986

본 연구에서는 SM20C를 모재로 하여 입경의 크기가 다른 3종의 복합조직강을 제작 동일한 분위기에서 저 및 고사이클 전영역에 걸쳐 피로특성을 검토하고져 한다. 제일보는 그 중 저사이클특성에 대한 보고이다. 일반적으로 저사이클 피로현상은 재 료가 탄소성 상태하에서 전위, 미소크랙, 보이드(void) 등의 인자가 복합적으로 작용 하여 발생함으로 변형률속도, 제어파형, 온도, 시험방법 및 분위기에 따라 많은 영향 을 받는다. 따라서 본 연구에서는 두가지 실험방법을 사용, 응력-변형율거동을 검토 복합조직강의 피로특성과 입경크기가 피로거동 및 강도에 미치는 영향을 비교 고찰하 였다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.307-310
• /
• 2003

Non-heat treated steels are attractive in the steel-wire industry since the spheroidization and quenching-tempering treatment are not involved during the processing. In this study, three different steels such as dual phase steel, low-Si steel, and ultra low carbon bainitic steel were used to investigate their deformation resistance and forming limit. Deformation resistance was estimated by calculating the deformation energy and the forming limit was evaluated by measuring the critical strain revealing crack initiation at the notch tip of the specimens. The results showed that deformation resistance was the lowest in the low-Si steel, and the forming limit strain was the highest in the ultra low carbon bainitic steel.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.5
• /
• pp.469-475
• /
• 1984

In dual phase steel composed of martensite and ferrite which are different in deformation behavior, the quantitative estimation of fracture toughness is investigated by the R-curve method and the stretched zone method of JSME Sool. In the homogeneous material J$_{IC}$ value measured by the R-curve method and the stretched zone method are almost equivalent each other, but in the inhomogeneous material J$_{IC}$ value by the stretched zone method is overestimated than that by the R-curve method. Such a overestimation for the J$_{IC}$ is due to the continuous plastic blunting of ferrite after the stretched zone width in martensite reached critical value which overmeasures the critical stretched zone width.width.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.1149-1152
• /
• 1999

In this paper we analyzed each region of specific points and ｅ-Δｅphase plane in order to make fuzzy rule base. After we composed the fuzzy control rules which can decrease rise time, delay time, maximum overshoot than basic fuzzy control rules. The composed method are converged more rapidly than single rule base in convergence region. Proposed method is alternately use at specific points of ｅ-Δｅphase plane with two fuzzy control rules, that is one control rule occruing the steady state error used in transient region and another fuzzy control rule use to decrease the steady state error and rapidly converge at the convergence region. Two fuzzy control rules in the ｅ-Δｅ phase plane decide the change time according to response characteristics of plants. As the results of simulation through the second order plant and the delay time plan, Proposed dual fuzzy control rules get the good response compare with the basic fuzzy control rule.

• Journal of the Optical Society of Korea
• /
• v.14 no.4
• /
• pp.363-367
• /
• 2010

A new two step on-axis digital holography (DH) is proposed without any assumptions, phase shifting, or complicated optical components. A dual-channel Mach-Zehnder interferometer was employed. Using that setup, the object field can be reconstructed requiring only two step measurements. To eliminate position difference between two charge-coupled device (CCD) cameras, a matched filter algorithm was used. Experimental results are compared to those of the traditional phase shifting technique. The proposed approach can also be applied to single-exposure on-axis DH for real time measurement.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.680-681
• /
• 2015

This paper proposes a comparative study of dual-airgap flux switching permanent magnet (FSPM) and spoke-type interior permanent magnet (S-IPM) machines equipped with phase-group concentrated-coil (PGCC) windings. Both of the investigated machines are the same size and material amounts which are compared at the same operating conditions. All the relevant machine performance including back electromotive force (EMF), cogging torque, and electromagnetic torque are analyzed by a 2-D time-stepping finite element method (FEM).

• Corrosion Science and Technology
• /
• v.5 no.1
• /
• pp.23-26
• /
• 2006

Recent development of ultrafine grained (UFG) low carbon steels by using equal channel angular pressing (ECAP) and their room temperature tensile properties are reviewed, focusing on the strategies overcoming their inherent mechanical drawbacks. In addition to ferrite grain refinement, when proper post heat treatments are imposed, carbon atom dissolution from pearlitic cementite during ECAP can be utilized for microstructural modification such as uniform distribution of nano-sized cementite particles or microalloying element carbides inside UFG ferrite grains and fabrication of UFG ferrite/martensite dual phase steel. The utilization of nano-sized particles is effective on improving thermal stability of UFG low carbon ferrite/pearlite steel but less effective on improving its tensile properties. By contrast, UFG ferrite/martensite dual phase steel exhibits an excellent combination of ultrahigh strength, large uniform elongation and extensive strain hardenability.