• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.289-292
• /
• 2008

Highly over-expanded nozzle of the rocket engines will be excited by non-axial forces due to flow separation at sea level operations. Since rocket engines are designed to produce axial thrust to power the vehicle, non-axial static and/or dynamic forces are not desirable. Several engine failures were attributed to the side loads. Present work investigate the unsteady flow in an over-expanded rocket nozzle in order to estimate side load during a shutdown/starting. Numerical computations has been carried out with density based solver on multi-block structured grid. Present solver is explicit in time and unsteady time step is calculated using dual time step approach. AUSMDV is considered as a numerical scheme for the flux calculations. One equation Spalart-Allmaras turbulence model is selected. Results presented here is for two nozzle pressure ratio i.e. 100 and 20. At 100 NPR, restricted shock separation (RSS) pattern is observed while, 20 NPR shows free shock separation (FSS) pattern. Side load is observed during the transition of separation pattern at different NPR.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.11
• /
• pp.1350-1357
• /
• 1988

The dual dielectric films have been grown on single-crystalline silicon substrates with the thickness ranging from 125A to 180A at various gas and temperature conditions by using rapid thermal process that included independent nitridation step. The film characteristics and their dependence on the contents of the hydrochloric gas and the processing time have been studied. By the addition of the hydrochloric gas, the initial oxide thickness was significantly changed, but after sequential nitridation processes the thickness of the films was nevertheless a little bit varied within 10A. All the samples of the dual dielectric films show the increased breakdown voltages in proportion to the additive contents of the hydrochloric gas and also show the higher breakdown strengths than the thermal oxide and nitrided oxide films grown by the conventional furnance process or the rapid thermal nitridation process that was composed of the dependent nitridation cycles.

• Journal of Positioning, Navigation, and Timing
• /
• v.4 no.4
• /
• pp.151-160
• /
• 2015

GPS L2C signal is a recently added civil signal to L2 frequency and is constructed by time division multiplexing of civil moderate (L2-CM) and civil long (L2-CL) code signals. While the L2-CM code is 20 ms-periodic and modulates satellite navigation message, the L2-CL code is 1.5s-periodic with 767,250 chips long code sequence and carries no data. Therefore, the L2-CL code signal allows receivers to perform a very long coherent integration. However, due to the length of the L2-CL code, the acquisition of the L2-CL code signal may take too long or require too much hardware resources. In this paper, we propose a three-step ultra-fast L2-CL code acquisition (TSCLA) technique for dual band GPS receivers. In the proposed TSCLA technique, a dual band GPS receiver sequentially acquires the coarse/acquisition (C/A) code signal at L1 frequency, the L2-CM code signal, and the L2-CL code signal to minimize mean acquisition time (MAT). The theoretical performance analysis and numerous Monte Carlo simulations show the significant advantage of the proposed TSCLA technique over conventional techniques introduced in the literature.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.5
• /
• pp.839-844
• /
• 2008

A novel state of health estimation method for hybrid electric vehicle lithium battery using sliding mode observer has been presented. A simple R-C circuit method has been used for the lithium battery modeling for the reduced calculation time and system resources due to the simple matrix operations. The modeling errors of simple model are compensated by the sliding mode observer. The design methodology for state of health estimation using dual sliding mode observer has been presented in step by step. The structure of the proposed system is simple and easy to implement, but it shows robust control property against modeling errors and temperature variations. The convergence of proposed observer system has been proved by the Lyapunov inequality equation and the performance of system has been verified by the sequence of urban dynamometer driving schedule test. The test results show the proposed observer system has superior tracking performance with reduced calculation time under the real driving environments.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.472-472
• /
• 2011

The capacitive coupled plasma (CCP) has been extensively used in the semiconductor industry because it has not only good uniformity, but also low electron temperature. But CCP source has some problems, such as difficulty in varying the ion bombardment energy separately, low plasma density, and high processing pressure, etc. In this reason, dual frequency CCP has been investigated with a separate substrate biasing to control the plasma parameters and to obtain high etch rate with high etch selectivity. Especially, in this study, we studied on the etching of $SiO_2$ by using the pulse-time modulation in the dual-frequency CCP source composed of 60 MHz/ 2 MHz rf power. By using the combination of high /low rf powers, the differences in the gas dissociation, plasma density, and etch characteristics were investigated. Also, as the size of the semiconductor device is decreased to nano-scale, the etching of contact hole which has nano-scale higher aspect ratio is required. For the nano-scale contact hole etching by using continuous plasma, several etch problems such as bowing, sidewall taper, twist, mask faceting, erosion, distortions etc. occurs. To resolve these problems, etching in low process pressure, more sidewall passivation by using fluorocarbon-based plasma with high carbon ratio, low temperature processing, charge effect breaking, power modulation are needed. Therefore, in this study, to resolve these problems, we used the pulse-time modulated dual-frequency CCP system. Pulse plasma is generated by periodical turning the RF power On and Off state. We measured the etch rate, etch selectivity and etch profile by using a step profilometer and SEM. Also the X-ray photoelectron spectroscopic analysis on the surfaces etched by different duty ratio conditions correlate with the results above.

• Journal of Korean Society of Transportation
• /
• v.26 no.2
• /
• pp.101-107
• /
• 2008

Traffic speed data may be missed due to detector malfunction or network problems. In this paper we have proposed effective methods to estimate the data which could not be collected through loop detectors. Our proposed algorithm has three steps. First step is to find the most similar neighbor data record by coefficient of correlation. Second step is to make some data records which is calculated by the 5 kinds of estimation methods. Third step is to compare the data records with history data record of observation link and thus the best method is selected. The proposed method is useful for estimating travel time.

• Physical Therapy Rehabilitation Science
• /
• v.4 no.1
• /
• pp.32-37
• /
• 2015

Objective: This study was conducted to test the effects of mobile texting and gaming on gait with obstructions under different illumination levels. Design: Cross-sectional study. Methods: Twelve healthy adults aged 20 to 36 years (mean 23.5 years) were tested under six different conditions. All participants used touchscreen smartphones. Testing conditions included: 1) Walking with an obstruction under a bright illumination level; 2) walking with an obstruction with a low level of illumination; 3) walking with an obstruction while texting under a bright illumination level; 4) walking with an obstruction while texting with a low level of illumination; 5) walking with an obstruction while gaming under a bright illumination level; and 6) walking with an obstruction while gaming with a low level of illumination. All participants were asked to text the Korean national anthem by their own phone and play Temple Run 2 using an iPhone 5. Gait variances were measured over a distance of 3 m, and the mean value after three trials was used. A gait analyzer was used to measure the data. Results: Compared to normal gait with obstruction, gait speed, step length, stride length, step time, stride time, cadence while texting and gaming showed significant differences (p<0.05). Differences between the illumination levels included gait speed, step length, stride length, and step time (p<0.05) with no significant differences in stride time and cadence. Conclusions: Dual-tasking using a smartphone under low levels of illumination lowers the quality of gait with obstructions.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.11
• /
• pp.1358-1366
• /
• 1988

The dual dielectric films have been grown on single-crystalline silicon substrates with the thickness ranging from 125A to 180A at various gas and temperature conditions by using rapid thermal process that included independent nitridation step. The film characteristics and their dependence on the contents of the hydrochloric gas and the processing time have been studied. By the addition of the hydrochloric gas, the initial oxide thickness was significantly changed, but after sequential nitridation processes the thickness of the films was nevertheless a little bit varied within 10A. All the samples of the dual dielectric films show the increased breakdown voltages in proportion to the additive contents of the hydrochloric gas and also show the higher breakdown strengths than the thermal oxide and nitrided oxide films grown by the conventional furnance process or the rapid thermal nitridation process that was composed of the dependent nitridation cycles.

• ETRI Journal
• /
• v.26 no.2
• /
• pp.185-188
• /
• 2004

In this paper, we design a two-step scheduling algorithm to support multiple bandwidth allocation policies for upstream channel access in an Ethernet passive optical network. The proposed scheduling algorithm allows us a simultaneous approach for multiple access control policies: static bandwidth allocation for guaranteed bandwidth service and dynamic bandwidth allocation for on-demand, dynamic traffic services. In order to reduce the scheduling complexity, we separate the process of the transmission start- time decision from the process of grant generation. This technique does not require the timing information of other bandwidth allocation modules, so respective modules are free from a heavy amount of timing information or complex processing.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1143-1153
• /
• 2015

In this paper, we propose an efficient architecture for a real-time image stitching engine for vision SoCs found in motor vehicles. To enlarge the obstacle-detection distance and area for safety, we adopt panoramic images from multiple telegraphic cameras. We propose a stitching method based on a fixed homography that is educed from the initial frame of a video sequence and is used to warp all input images without regeneration. Because the fixed homography is generated only once at the initial state, we can calculate it using SW to reduce HW costs. The proposed warping HW engine is based on a linear transform of the pixel positions of warped images and can reduce the computational complexity by 90% or more as compared to a conventional method. A dual-core SW/HW image stitching engine is applied to stitching input frames in parallel to improve the performance by 70% or more as compared to a single-core engine operation. In addition, a dual-core structure is used to detect a failure in state machines using rock-step logic to satisfy the ISO26262 standard. The dual-core SW/HW image stitching engine is fabricated in SoC with 254,968 gate counts using Global Foundry's 65 nm CMOS process. The single-core engine can make panoramic images from three YCbCr 4:2:0 formatted VGA images at 44 frames per second and frequency of 200 MHz without an LCD display.