• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.4
• /
• pp.279-285
• /
• 2020

An open-end winding (OEW) permanent magnet synchronous motor with dual inverters can synthesize large voltages for a motor with the same DC link voltage. This ability has the advantage of reducing the use of DC/DC boost converters or high voltage batteries. However, zero-sequence voltage (ZSV), which is caused by the difference in the combined voltage between the primary and secondary inverters, can generate a zero-sequence current (ZSC) that increases system losses. Among the methods for eliminating this phenomenon, combining voltage vector eliminated ZSV cannot be accomplished by the conventional Pulse Width Modulation(PWM) method. In this study, a PWM carrier generation method using functionalization to generate a switching pattern to suppress ZSC is proposed and applied to analyze the control influence of the center-zero vector in the switching sequence about the current ripple.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.3181-3183
• /
• 2000

As the fact that the simple data of text and sound in early year have been changed to be high quality images and sounds. PLL(Phase-Locked Loop) system plays an important role in communication system. VCO(Voltage Controlled Oscillator) is the most important part in PLL system because it can have critical effects on operation of PLL. Recently, it has been raised the necessity of high speed and high accuracy circuit application. In this paper, a new differential voltage clamped VCO using negative-skewed path is suggested. Using a dual-delay scheme to implement the VCO, higher operation frequency and wider tuning are achieved simultaneously. The dual-delay scheme means that both the negative skewed delay paths and the normal delay paths exist in the same ring oscillator. The negative skewed delay paths decrease the unit delay time of the ring oscillator below the single inverter delay time. As a result, higher operation frequency can be obtained. The whole characteristics of VCO are simulated by using HSPICE. Simulation results show that the resulting operating frequencies are 50% higher than those obtainable from the conventional approaches.

• Convergence Security Journal
• /
• v.15 no.3_1
• /
• pp.99-105
• /
• 2015

A typical SRAM-based PUF is used in random number generation and key exchange process. The generated out puts should be preserved, but the values are changed owing to the external environment. This paper presents a new D-PUF logic employing a dual anti-fuse OTP memory to the SRAM-based PUF. The proposed PUF can enhance the reliability of the logic since it can preserve the output values. First, we construct the OTP memory using an anti-fuse. After power up, a SRAM generates the random values owing to the mismatch of cross coupled inverter pair. The generated random values are programed in the proposed anti-fuse ROM. The values that were programed in the ROM at once will not be changed and returned. Thus, the outputs of the proposed D-PUF are not affected by the environment variable such as the operation voltage and temperature variation, etc. Consequently, the reliability of the proposed PUF will be enhanced owing to the proposed dual anti-fuse ROM. Therefore, the proposed D-PUF can be stably operated, in particular, without the powerful ECC in the external environment that are changed.

• Journal of electromagnetic engineering and science
• /
• v.18 no.2
• /
• pp.117-128
• /
• 2018

In this paper, compact linear dual polarized series-fed $1{\times}2$ linear and $2{\times}2$ planar arrays antennas for airborne SAR applications are proposed. The proposed antenna design consists of a square radiating patch that is placed on top of the substrate, a quarter wave transformer and $50-{\Omega}$ matched transformer. Matching between a radiating patch and the $50-{\Omega}$ microstrip line is accomplished through a direct coupled-feed technique with the help of an impedance inverter (${\lambda}/4$ impedance transformer) placed at both horizontal and vertical planes, in the case of the $2{\times}2$ planar array. The overall size for the prototype-1 and prototype-2 fabricated antennas are $1.9305{\times}0.9652{\times}0.05106{{\lambda}_0}^3$ and $1.9305{\times}1.9305{\times}0.05106{{\lambda}_0}^3$, respectively. The fabricated structure has been tested, and the experimental results are similar to the simulated ones. The CST MWS simulated and vector network analyzer measured reflection coefficient ($S_{11}$) results were compared, and they indicate that the proposed antenna prototype-1 yields the impedance bandwidth >140 MHz (9.56-9.72 GHz) defined by $S_{11}$<-10 dB with 1.43%, and $S_{21}$<-25 dB in the case of prototype-2 (9.58-9.74 GHz, $S_{11}$< -10 dB) >140 MHz for all the individual ports. The surface currents and the E- and H-field distributions were studied for a better understanding of the polarization mechanism. The measured results of the proposed dual polarized antenna were in accordance with the simulated analysis and showed good performance of the S-parameters and radiation patterns (co-pol and cross-pol), gain, efficiency, front-to-back ratio, half-power beam width) at the resonant frequency. With these features and its compact size, the proposed antenna will be suitable for X-band airborne synthetic aperture radar applications.

• Journal of Power Electronics
• /
• v.13 no.2
• /
• pp.256-263
• /
• 2013

This paper presents an IHQRR (Integrated High Quality Rectifier Regulator) BIFRED (Boost Integrated Flyback Rectifier Energy Storage DC-DC) converter fed BLDC (Brushless DC) motor drive. A reduced sensor topology is derived by utilizing a BIFRED converter to operate in a dual DCM (Discontinuous Conduction Mode) thus utilizing a voltage follower approach for the PFC (Power Factor Correction) and voltage control. A new approach for speed control is proposed using a single voltage sensor. The speed of the BLDC motor drive is controlled by varying the DC link voltage of the front end converter. Moreover, fundamental frequency switching of the VSI's (Voltage Source Inverter) switches is used for the electronic commutation of the BLDC motor which reduces the switching losses in the VSI. The proposed drive is designed for a wide range of speed control with an improved power quality at the AC mains which falls within the recommended limits imposed by international power quality standards such as IEC 61000-3-2.

• Journal of Magnetics
• /
• v.21 no.3
• /
• pp.399-404
• /
• 2016

This paper presents a new permanent magnet (PM) assisted topology for a recently introduced brushless wound rotor synchronous machine (BL-WRSM) [1]. The BL-WRSM had a dual-inverter configuration for generating a composite magneto motive force (MMF) with a fundamental component and a subharmonic component. The subharmonic component of the MMF is used for brushless excitation of the rotor. In this paper, additional PMs were introduced on the rotor of the BL-WRSM, making it a hybrid BL-WRSM. We also discussed the flux weakening operation for the hybrid BL-WRSM. The hybrid BL-WRSM offered advantages for starting the machine and provided better performance under full-load conditions. The finite element method (FEM) was used to analyze the performance of the hybrid BL-WRSM, and we compared its performance with BL-WRSM. Finally, prototypes were built with and without the PM-assistance, and experiments were conducted to demonstrate their performance.

• Proceedings of the KIPE Conference
• /
• 2012.11a
• /
• pp.13-14
• /
• 2012

이중 인버터를 이용한 개방 권선 전동기 구동 시스템에서 한 인버터의 DC 링크만 전원에 연결하고 추가된 인버터의 DC 링크는 전원에 연결하지 않는 경우, 전원이 연결되지 않은 인버터의 전압은 승압이 가능하게 된다. 때문에 일반적인 단일 인버터를 이용하여 전동기를 구동하는 경우보다 높은 전압을 전동기에 인가할 수 있게 되고, 따라서 약자속 영역에서 전동기가 더 많은 토크와 파워를 출력할 수 있다는 장점을 가진다. 하지만 본 논문에서 사용하는 이중 인버터의 경우 유효전력과 무효전력을 분리하여 제어하여야 하기 때문에 기존과는 다른 약자속 방법을 필요로 하게 된다. 따라서 본 논문에서는 표면 부착형 영구자석 전동기의 이중 인버터 구동 시스템에서 유효전력 분 전압의 크기를 최대화하는 약자속 제어방법을 제안하고 모의실험을 통해 그 효용성을 검증하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.128-128
• /
• 2010

The high-voltage X-ray generator recently used is very popular, because that can be miniaturized, increased in generating efficiency, elaborated in output control. All these features are available with high-frequency made by using an inverter, the fast switching semiconductor device. In this paper to identify the differences among types of rectification, we compared output ripple with full-wave rectification and dual-voltage rectification methods.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.552-554
• /
• 2006

BIPV(Building Integrated PV) system can expect dual effects that reduce expenses for establishment of PV system by adding new function as outer covering material of building expect producing the electricity. But, there are many generation differences according to the exterior environmental facts(solar cell array, design and installation condition of interactive inverter system) Therefore, it is difficult to optimum design. Consequently in advance design system, we experiment 3kW BIPV(Building Integrated PV) generation. We concrete PV system efficient application of variable. BIPV system that is proposed in this paper, was established in Solar Energy research center of Chosun University, composed with system. This research is a basic study for application of building integrated photovoltaic system for building

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.835-837
• /
• 2002

The 17" Backlight Unit (BLU) employing twelve EEFLs (External Electrode Fluorescent Lamp) has been developed for LCD-TV The characteristics of the EEFL BLU without dual brightness enhancement film (DBEF) were equivalent to those of CCFL (Cold cathode Fluorescent Lamp) BLU employing eight CCFLs with DBEF. Luminance, power consumption and uniformity were 12,000nits, 32watt and 80%, respectively. The inverter of EEFL Backlight Unit is composed of 2 transformers and driven by the sinusoidal waveform.