• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.494-497
• /
• 2006

The objectives of this study are to develop and evaluate the Neural Network algorithm which can predict the inelastic shortening such as the creep strain and the drying shrinkage strain of reinforced concrete members using the previous test data. New learning algorithms for the prediction of creep strain and the drying shrinkage strain are proposed focusing on input layer components and a normalization method for input data and their validity is examined through several test data. In Neural Network algorithm, the main input data to be trained are the compressive strength of the concrete, volume to surface ratio, curing condition, relative humidity, and the applied load. The results show that the new algorithms proposed herein successfully predict creep strain and the drying shrinkage strain.

• The Korean Journal of Ceramics
• /
• v.6 no.1
• /
• pp.37-42
• /
• 2000

To reduce shrinkage and the possibility of fracture during ambient pressure drying, it is of great importance to increase the strength and stiffness of the wet gels. In this paper is presented the strengthening and stiffening of wet silica gels prepared from sodium silicate (water glass) as well as properties of the corresponding xerogels. By washing gels containing different initial silica contents in water solutions at elevated pH, a maximum in shear modulus of ~4 MPa was obtained. The maximum stiffness enabled xerogels with bulk density of 0.28g/$\textrm{cm}^3$ to be made regardless of silica content and washing conditions. However, by aging the wet gels in a solution providing fresh monomers to the gel network, a shear modulus of 20 MPa was obtained after 27h. By this method monolithic xerogels with a density down to ~0.2g/$\textrm{cm}^3$ was prepared. The results are compared to alkoxide based gels.

• Journal of Biosystems Engineering
• /
• v.12 no.1
• /
• pp.39-44
• /
• 1987

Measurement methods of moisture content were compared with 7 dried vegetables (red pepper, onion, green onion, garlic, ginger, carrot and radish). The moisture contents of dried vegetables having different moisture contents were determined by atmospheric oven drying, infrared balance, vacuum oven and Karl Fisher methods. Vacuum oven and Karl Fisher methods gave the relatively agreed results and considered to give the accurate moisture content. Atmospheric oven drying and infrared balance methods resulted in higher moisture content than methods mentioned above, because of the thermal decomposition of solid. Calibration of the moisture data of atmospheric oven drying method into the vacuum oven data was undertaken. The thermodecomposable solid fraction was high in onion, radish, green onion and carrot, and was in the range of 8.0-11.7% of the total solid in these products.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.1
• /
• pp.87-92
• /
• 1998

Major characteristics of shrinking and rehydration of Korean tea-leaves were investigated in the hot-air drying equipment. Experiments were performed with various drying temperature, plucking time, heating method and rolling condition. The values of shrinking raito and rate were the highest at 7$0^{\circ}C$ in the range of 3$0^{\circ}C$ to 9$0^{\circ}C$. The 1st tea-leaves and showed higher values. Shrinking ratio was 16.62 and 19.62% for leaves and stems; shrinking rate was found 0.083 and 0.091cm/hr.cm, respectively. The rehydration characteristics of tea-leaves at the drying temperature of 3$0^{\circ}C$ were fairly satisfactory. The 2nd tea-leaves showed higher value than others, while the natural tea-leaves were lower. Average rehydration ratio and rehydration rate constant were 85.7% and 0.063/min for leaves; 80.1% and 0.032/min for stems, respectively.

• KCI Concrete Journal
• /
• v.14 no.1
• /
• pp.15-22
• /
• 2002

Stresses that develop due to differential shrinkage between polymer modified cement mortar (PM) and Portland cement concrete (PCC) in a repaired concrete beam at early ages were investigated. Interface delamination or debonding of the newly cast repair material from the base is often observed in the field when the drying shrinkage of the repair material is relatively large. This study presents results of both experimental and analytical works. In the experimental part of the study, development of the material properties such as compressive strength, elastic modulus, interface bond strength, creep constant, and drying shrinkage was investigated by testing cylinders and beams for a three-week period in a constant-temperature chamber. Development of shrinkage-induced strains in a PM-PCC composite beam was determined. In the analytical part of the study, two analytical solutions were used to compare the experimental results with the analytically predicted values. One analysis method was of an exact type but could not consider the effect of creep. The other analysis method was rather approximate in nature but the creep effect was included. Comparison between the analytical and the experimental results showed that both analytical procedures resulted in stresses that were in fair agreement with the experimentally determined values. It may be important to consider the creep effect to estimate shrinkage-induced stresses at early ages.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.6 no.1
• /
• pp.67-73
• /
• 1998

This study was to experiment, through sewage sludge treatment by Vacuum Drying Method, variation of water content with reaction pressure, reaction time, reaction temperature. The result are as follows; The water content decreased with the same reaction temperature and reaction time at lower pressure and 360~40 mmHg (a close vacuum) showed lower water content at low reaction temperature and short reaction time. The water content rapidly decreased with the same reaction pressure and time at low reaction temperature (above $120^{\circ}C$).

• Journal of Pharmaceutical Investigation
• /
• v.32 no.3
• /
• pp.173-179
• /
• 2002

Solid dispersions of ipriflavone with PVP were prepared by a spray-drying method in order to improve the bioavailability. They were measured with scanning electron microscopy, differential scanning calorimetry, x-ray powder diffraction, and Fourier transform infrared spectroscopy to evaluate the physicochemical interaction between ipriflavone and PVP and study the correlation between these physicochemical characteristics and bioavailability. Ipriflavone exhibited crystallinity, whereas PVP was almost amorphous. The area of the endotherm $({\Delta}H)$ of freezer milled ipriflavone, freezer milled ipriflavone physically mixed with freezer milled PVP, and physically mixed ipriflavone with PVP was almost the same, whereas ${\Delta}H$ of the solid dispersed ipriflavone with PVP was much smaller than that of the other preparation types. Also, the crystallinity and the crystal size of ipriflavone in the solid dispersed ipriflavone with PVP were much smaller than those of the other preparation types. From the in vivo test, the AUC of the solid dispersed ipriflavone with PVP was approximately 10 times higher than that of the physically mixed ipriflavone with PVP. The solid dispersion using the spray-drying method with a water-soluble polymer, PVP, may be effective for the improvement of the bioavailability.

• Journal of the Korean Ceramic Society
• /
• v.32 no.9
• /
• pp.1047-1055
• /
• 1995

Mn-Zn ferrite granules were formed by a spray-drying method of the slurry containing different kinds and concentrations of binders at various temperatures. The slurry was made by conventional ceramic processing method, that is, by mixing Fe2O3, MnO, ZnO powders (52 : 24 : 24 mol%), calcining and milling. Typical shape of the spray dried granules was spherical. The compaction behavior of these granules was dependent on the spray-drying temperature and the kind and concentration of binders. At lower pressure the granules were displaced and at higher pressure the granules were deformed and fractured to fill pores among the granules. The optimum concentration of the binder was 0.5wt%. The granules containing 0.5wt% PVA 205 were deformed and fractured well and the green density was higher than others. At higher concentrations of the binder the granules were deformed rather than fractured, therefore the green density was lowered because of the remaining unfilled pores. The decomposition temperature and the heat released were increased with increasing the concentration of the binders. The compaction response of the granules containing PVA 205 was more efficient than those containing PVA 217 and PVA 117. Green density was not dependent on the degree of hydrolysis of the binders. The compaction response of the granules spray-dried at 15$0^{\circ}C$ was most efficient.

• Journal of Korea Society of Waste Management
• /
• v.35 no.7
• /
• pp.600-605
• /
• 2018

In this study, the combustion characteristics were investigated based on the biodrying solid recovered fuel (SRF) in a 5 Ton/day scale combustion boiler. The composition of the combustion gas containing the biodrying SRF was analyzed, the particulate matter, and its HCl content was determined with the air pollutant process test method. Mass balance, carbon balance, and combustion efficiency were calculated according to the equivalence ratio (ER) method; the energy recovery efficiency of the combustion boiler was also analyzed. The overall combustion efficiency of the biodrying SRF was 97.3 % and the energy recovery efficiency was 80.2%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.2
• /
• pp.72-75
• /
• 2008

Zinc oxide (ZnO) thin films were prepared by a sol-gel method. The structural and electrical properties were investigated by varying drying and annealing temperatures. The thin films were coated (250 nm) by spin-coating method on glass substrates. The optimum drying temperature of ZnO thin films was 300$^{\circ}C$ where the resistivity was the lowest and the preferred c-axis orientation was the highest. The annealing was carried out in air and inert atmospheric conditions. The degree of the preferred c-axis orientation was estimated. The highest preferred c-axis orientation was recorded at 600$^{\circ}C$. The preferred c-axis orientation and grain growth resulted in the mobility enhancement of the ZnO thin films, and the lowest resistivity was 0.62${\Omega}{\cdot}cm$ at 600$^{\circ}C$.