• 공학논문집
• /
• 제8권1호
• /
• pp.31-50
• /
• 2006

수축은 콘크리트에 균열을 발생시키는 경우도 있다. 일반적 조건하에서는 콘크리트의 건조를 피할 수 없으며 건조가 일어나면 수축이 생기므로 대부분의 콘크리트 적용분야에서는 실제로 이와 같이 균열발생을 고려하여야 한다. 균열이 발생한 콘크리트는 균열이 없는 콘크리트에 비하여 강도가 약하고 투과성이 크며 화학적 침식의 영향을 받기 쉽다. 또 재령의 경과에 따라 경량기포콘크리트의 강도발현은 기포제의 종류, 물과 시멘트와의 비, 양생조건 및 기간 등과 같은 인자에 의존하고 있다. 경량기포콘크리트의 강도가 높으면 높을수록 수축에 의하여 균열이 발생할 가능성이 감소한다. 그러므로 온돌구조용으로의 경량기포콘크리트의 강도는 소포율과 시멘트의 건조수축과의 균열저감효과에 크게 의존된다.

• 한국의류학회지
• /
• 제40권2호
• /
• pp.305-314
• /
• 2016

This paper investigated the applicable possibility of PTT and wool staple fibers to the air vortex system as high quality yarns for a high emotional and comfort garment. It was found that the tactile hand of vortex yarn knitted fabrics was harsher than ring and compact yarns knitted fabrics. It was observed that formability and sewability of air vortex yarn knitted fabrics seemed worse than ring and compact yarns due to low tensile and compressional resilience and high bending and shear hysteresis of air vortex yarn knitted fabrics. It revealed that wicking and drying rates of air vortex yarn knitted fabric were better than ring and compact yarns; in addition, the heat keepability of vortex yarn knitted fabric was higher than ring and compact yarns due to low thermal conductivity and max heat flow rate ($Q_{max}$). Any difference of thermal shrinkage between air vortex and ring yarn knitted fabrics was not shown, but pilling characteristic of air vortex yarn knitted fabric was superior. However, it was shown that wicking, drying, thermal property and pilling characteristics of air vortex yarn knitted fabric were superior due to air vortex yarn structure with parallel fibers in the core part and periodical and fasciated twists in the sheath part of the yarns.

• 한국분말재료학회지
• /
• 제19권4호
• /
• pp.259-263
• /
• 2012

Dependence of the freeze-drying process condition on microstructure of porous W and pore formation mechanism were studied. Camphene slurries with $WO_3$ contents of 10 vol% were prepared by milling at $50^{\circ}C$ with a small amount of dispersant. Freezing of a slurry was done in Teflon cylinder attached to a copper bottom plate cooled at $-25^{\circ}C$. Pores were generated subsequently by sublimation of the camphene during drying in air for 48 h. The green body was hydrogen-reduced at $800^{\circ}C$ for 30 min, and sintered in the furnace at $900^{\circ}C$ for 1 h. After heat treatment in hydrogen atmosphere, $WO_3$ powders were completely converted to metallic W without any reaction phases. The sintered samples showed large pores with the size of about $70{\mu}m$ which were aligned parallel to the camphene growth direction. Also, the internal wall of large pores and near bottom part of specimen had relatively small pores with dendritic structure due to the growth of camphene dendrite depending on the degree of nucleation and powder rearrangement in the slurry.

• Journal of the Korean Wood Science and Technology
• /
• 제47권5호
• /
• pp.567-578
• /
• 2019

A common problem with fast-growing hardwoods is dimensional instability that limits use of their wood. In this study, we investigated the effects of pre-drying methods, temperatures, and heating duration on the specific gravity, water absorption, and dimensional stability of three tropical fast-growing hardwoods, jabon (Neolamarckia cadamba Roxb.), sengon (Falcataria moluccana Miq.), and mangium (Acacia mangium Willd.). Wood samples were pre-dried by two methods (fan and oven at $40^{\circ}C$), and heat treatments were performed at three temperatures (120, 150, and $180^{\circ}C$) for two different time periods (2 and 6 hours). The specific gravity, water absorption, dimensional stability, and structural changes of the samples were evaluated. The results revealed that heat treatments slightly reduced the specific gravity of all three wood species. In addition, the heat treatments reduced water absorption and significantly improved dimensional stability of the samples. Oven pre-drying followed by heat treatment at $180^{\circ}C$ for 6 hours resulted in good physical improvement of jabon and sengon wood. Fan pre-drying followed by heat treatment at $180^{\circ}C$ for 2 hours improved the physical properties of mangium wood. The heat treatment shows a promising technique for improving the physical characteristic of fast growing hardwoods.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.28-33
• /
• 2006

Shallow failures of slopes in weathered soils are caused by infiltration due to prolonged rainfall. These failures are mainly triggered by the deepening of the wetting band accompanied by a decrease in suction induced by the water infiltration. In this paper, hysteresis on soil-water characteristic curve(SWCC) of granite and gneiss weathered soils are investigated using transient flow analysis respectively. Each case was subjected to artificial rainfall intensities and time duration depending on the laboratory-based drying and wetting processes. The results show that the unsaturated seepage on weathered slopes are very much affected by the initial suction of soils and unsaturated permeability of the soils. In addition, a granite weathered soil has a lower air-entry value, residual matric suction, and wetting front suction and less hysteresis loop than a gneiss weathered soil.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 추계 학술논문 발표대회
• /
• pp.134-135
• /
• 2015

This study analysed compressive strength and the expansion characteristic to utilize a high volume mineral admixture mortar for a aerated mortar and a plastering mortar. In this experiment, the result shows that the compressive strength gain was satisfactory in case that WR was replaced within 5%. Also, the difference between WR1 and WR was insignificant. It shows that the drying shringkage properties at large was showed being satisfactory generally compared with Plain when WR was replaced, but the effect was not significant.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2002년도 제25회 KOSCI SYMPOSIUM 논문집
• /
• pp.185-192
• /
• 2002

A laboratory scale thermogravimetric analyser was developed to investigate the combustion characteristics of selected solid fuel(wood) in the highly preheated air. The aims are to introduce in the means of experimental determination of the solid fuel particle characteristics through the combustion process in the environment of highly preheated air. A nearly single particle combustion condition was reproduced in a thermogravimetric analyser and regenerating combustor. For a fuel particle whose characteristic length was a few centimeter, the sub-processes of fuel drying, pyrolysis as well as the combustion of residual carbon were identified. Fluidized environment of carrier gas was selected as the major parameter which affect the combustion process.

• 한국안전학회지
• /
• 제27권6호
• /
• pp.133-137
• /
• 2012

Cracking may be used to help predict the cause of deterioration of concrete, since in many cases characteristic cracking patterns are produced. The purpose of this paper is an analysis of the crack cause occurred in concrete faced rockfill dams. We analyzed the concrete placement methods, cracking pattern, the inspection of crack depth by the ultrasonic pulse velocity method, and the measurement of heat of hydration, environmental condition, and so on. In this study, the crack cause of concrete faced rockfill dam is the wrong method of concrete placement, high temperature difference by cement of heat of hydration and concrete of drying shrinkage.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.555-558
• /
• 2004

In this paper, the variable producing conditions of YBCO superconducting powder by use of sol-gel method was investigated. YBCO superconducting powder which was prepared by sol-gel method was shown the characteristic gel formation, particle size and its properties under variable preparation conditions, such as pH, drying and processing time, and powder heat treatment, etc.

• 신재생에너지
• /
• 제2권1호
• /
• pp.46-55
• /
• 2006

The performance enhancement of heat exchanger in the drying system using solar collector with evacuated tubes is analyzed. First, for this analysis, the heat loss from a reversed trapezoidal fin attached at the pipe is calculated as a function of convection characteristic number ratio, fin base length and fin tip length. Also, the optimum heat loss and fin tip length of the fin under certain conditions are presented. The overall surface effectiveness of the cylinder with reversed trapezoidal fins in the heat exchanger are shown as a function of half fin base height, fin lateral slope and fin tip length.