• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.1
• /
• pp.93-102
• /
• 2023

This study conducted an effect evaluation before and after the installation of a vehicle information guidance system that provides drivers with information about vehicle speed and the presence or absence of pedestrians near pedestrian crossings. There are three types of scenarios: when no information is provided to the driver (S1), when only the vehicle driving speed is provided (S2), and when pedestrians are present on the pedestrian crossing and when both vehicle driving speeds are provided (S3). did. As a result of the survey, the speed reduction rate of the vehicle was found to be about 0.4~0.7km greater in S2 and S3 that provide information to the driver than in scenario S1. In addition, in the scenario S3, the speed reduction rate is 0.2km higher than that in the case where there are pedestrians near the pedestrian crossing, which further reduces the vehicle speed. Statistical analysis also showed that there was a difference in the speed reduction rate of the average vehicle for the three scenarios, and that the speed reduction rate was large in the presence of pedestrians.

• Journal of the Korea Convergence Society
• /
• v.9 no.4
• /
• pp.1-7
• /
• 2018

Electric motors for electric vehicles differ in efficiency characteristics depending on the operation modes, studies for evaluating high efficiency characteristics in low speed and high speed operation modes are very important. Therefore, it is necessary to design method that can change the high torque, high output density, and high efficiency characteristics of driving motors for electric vehicles. In this paper, the diameter ratio of stator and rotor for the interior permanent magnet synchronous motor is change of designed 0.62, 0.65, and 0.68, respectively, and the efficiency characteristics of the entire operation section, average efficiency characteristics of the city driving modes and express highway driving modes are analyzed. As a result of analyzing the efficiency characteristics of the entire operating section, it was confirmed that as the diameter ratio increases, the high efficiency section moves to the low speed and low torque section and the high efficiency section moves to the high speed and low torque neighborhood as the diameter ratio decreases. As a result of analyzing the average efficiency characteristics in the city driving modes and express highway driving modes, the average efficiency of 0.68 model is analyzed to be more efficient than the 0.63 and 0.65 model ratio, and it is confirmed that it is suitable for city driving modes and express highway driving modes.

• Journal of Korean Society of Transportation
• /
• v.29 no.4
• /
• pp.7-15
• /
• 2011

Emerged in early 1990s, so called 'Quick service' industry that provides faster delivery of small parcels than regular mail service accelerated use of motorcycles. As the economic grows, use of large bicycles (more than 250CC displacement) for leisure purpose has also rapidly increased. Traffic crash data clearly shows the increasing trend in motorcycle crashes. The ratio of motorcycle involved crashes out of total has increased from 5.7% in 2005 to 8.3% in 2008, and similar trend can be found in fatalities ratio as well. In this study, we assess the level of risk when motorcycles operate on motorways by analyzing traffic rule violation ratio, lane change behaviour, driving speed behaviors of motorcycles in Uninterrupted Traffic Flow Facilities and using PC-CRASH simulation we also calculate car shock impulses occurred when an accident happens. Analysis result shows that the motorcycle is different from the car in terms of lane change timing and average speed, and also shows motorcycle drivers tends to conduct more improper driving behavior particularly when traffic is congested. The results from this study could be usefully applied when the law enforcement agent decides whether bicycles shall be allowed to use motorways. The result could be also utilized as fundamental information for further study of bicycles' driving behavior.

• Journal of Korean Society for Atmospheric Environment
• /
• v.28 no.5
• /
• pp.506-517
• /
• 2012

Electronic Toll Collection System (ETCS), so called "Hi-Pass" in Korea, has improved traffic flow at toll gate of highways. It is known that the improvement of traffic flow should reduce air pollutants and $CO_2$ from vehicles. In this study, real driving emission of a light duty truck with Portable Emission Measurement System(PEMS) has been measured to evaluate the emission reduction effect due to ETCS. The correlations between driving variables and emissions have been analyzed to verify its effect on traffic flow improvement and emission reduction at toll gate. We considered average vehicle speed, Relative Positive Acceleration (RPA), and the distance of queue as driving variables. Compared to passing Manual Toll Collection System (MTCS) lane without queue, ETCS was able to reduce 38.7% of $NO_x$, 21.6% of soot, and 27.7% of $CO_2$. The results showed that the higher the average vehicle speed, the lower RPA and no queue in ETCS contributed to the emission reductions. Linear equation models with RPA and queue have been established by the multiple linear regression method. The linear models resulted in the higher coefficient of determination than those with only average vehicle speed used for establishing vehicle emission factors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.5
• /
• pp.103-110
• /
• 2020

Bio-inspired underwater robots have been studied to improve the dynamic performance of fins, such as swimming speed and efficiency, which is the most basic performance. Among them, bio-inspired soft robots with a compliant tail fin can have high degrees of freedom. On the other hand, to improve the driving efficiency of the compliant fins, the stiffness of the tail fin should be changed with the driving frequency. Therefore, a new type of variable stiffness mechanism has been developed and verified. This study, which was inspired by the anatomy of a real dolphin, assessed a process of designing and manufacturing a robotic dolphin with a variable stiffness mechanism. By mimicking the vertebrae of a dolphin, the variable stiffness driving part was manufactured using subtractive and additive manufacturing. A driving tendon was placed considering the location of the tendon in the actual dolphin, and the additional tendon was installed to change its stiffness. A robotic dolphin was designed and manufactured in a streamlined shape, and the swimming speed was measured by varying the stiffness. When the stiffness of the tail fin was varied at the same driving frequency, the swimming speed and thrust changed by approximately 1.24 and 1.5 times, respectively.

• The Research Journal of the Costume Culture
• /
• v.25 no.4
• /
• pp.499-508
• /
• 2017

Functional inner-wear being currently sold is being made without regard to the characteristics of various sports events. The purpose of this study is to identify this problem and to investigate the effect of sports taping on golf swing when wearing functional inner-wear. The subjects of this study were 8 male golfers belonging to Korea Professional Golf Association, and Launch monitor and Trackman were used to find out golf club action, ball pitch, distance, etc. There are three types of clubs: driver, wood, and iron, and the first experiment was carried out using only functional inner-wear. In the second experiment, we experimented with functional inner-wear after sports taping, and we compared and analyzed the distance depending on each experiment, the speed of the ball and the club, and the accuracy of the club face. The results of the study were as follows. As a result of driving distance, according to the presence of sports taping on functional inner-wear, there was a statistically significant difference in the driving swing and wood swing, for club and ball speed, there was a statistically significant difference only in the driving swing. Regarding the accuracy by the presence of sports taping on inner-wear, there was a statistically significant difference in the driving swing, wood swing, and iron swing. In conclusion, the sports taping in the functional inner-wear had a positive effect on golf performance improvement, and we hope that golf inner-wear these two specifications combing will be developed in the future.

• Tribology and Lubricants
• /
• v.31 no.4
• /
• pp.141-147
• /
• 2015

Gas foil thrust bearings (GFTBs) have attractive advantages over rolling element bearings and oil film thrust bearings, such as oil-free operation, high speed stability, and high-temperature operation. However, GFTBs have lower load carrying capacity than the other two types of bearings owing to the inherent low gas viscosity. The load carrying capacity of GFTBs depends mainly on the compliance of the foil structure and the formed hydrodynamic wedge, where the gas pressure field is generated between the top foil and the thrust runner. The load carrying capacity of the GFTBs is very important for the suitable design of oil-free turbomachinery with high performance. The aim of the present study is to identify the characteristics of the load carrying performance of GFTBs. A new test rig for the experimental measurements is designed to provide static loads up to 800 N using a pneumatic cylinder. The maximum operating speed of the driving motor is 30,000 rpm. A series of experimental tests—lift-off test, static load performance test, and maximum load capacity test—estimate the performance of a six-pad GFTB, in terms of the static load, driving torque, and temperature. The maximum load capacity is determined by increasing the static load until the driving torque rises suddenly with a sharp peak. The test results show that the torque and temperature increase linearly with the static load. The estimated maximum load capacity per unit area is approximately 80.5 kPa at a rotor speed of 25,000 rpm. The test results can be used as a design guideline for GFTBs for realizing oil-free turbomachinery.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.6
• /
• pp.607-613
• /
• 2009

In this paper, we made a simple paper feeding system which is one of MTS (media transport system) and controllers. The plant has a flexible paper and two driving rollers and two driven rollers. The control system has two conventional PID controllers. Skew angle and feeding speed of MTS deteriorate the quality of feeding system. In order to control a feeding speed and skew of feeding paper, we control rotational velocity of two driving rollers. Therefore, this controller has two inputs and two outputs as MIMO (multi-input and multi-output) system. The control inputs were the feeding speed and the skew displacement of the paper. The control outputs were the rotational velocity to each driving roller. To find appropriate PID gains of two controllers, we proposed an optimization technique. We assume the system variables and performance of a whole system as follows. PID gains of two controllers for skew and feeding speed are system variables. System performance is both skew and feeding speed. We simulates to making mathematical correlation using global Kriging interpolation. To find appropriate value of system variables, optimization method is simulation in sequence as following method. First, the optimization solver simulates with DOE (design of experiment) tables to find correlation equation of both system variable and performances. Then, the solver guesses the appropriate values and simulates if the system variables are appropriate or not. If the result of validation doesn't satisfy the convergence and iteration tolerance, the solver makes a new Kriging models and iterates this sequence until satisfy the tolerances.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.64-70
• /
• 2018

Rollover is a major concern for vehicles with a higher center of gravity and for improving driving performance. This study investigates a tilting system to prevent rollover, which was successfully implemented for high-speed trains. It may be useful to apply the concept of the tilting system to a large truck such as a trailer. Even a small adjustment in the tilting angle can improve the driving stability during a steep turn. The equation of motion was derived from a dynamic model of the trailer with the tilting system. The balance of the centrifugal force and normal force determines the rollover critical speed for a given radius of the turn and load. To obtain a more conservative criterion, the rollover critical state was defined as the instant when any side wheel loses contact with the road. To actuate the tilting system, the optimal tilting angle must be calculated from the steering angle and the vehicle speed. Using a simplified model of a large truck, the effects of the tilting angle and load on the rollover critical speed were investigated.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.7
• /
• pp.734-741
• /
• 2009

A new localization algorithm is proposed for a fast moving mobile robot, which utilizes only one beacon and the global features of the differential-driving mobile robot. It takes a relatively long time to localize a mobile robot with active beacon sensors since the distance to the beacon is measured by the traveling time of the ultrasonic signal. When the mobile robot is moving slowly the measurement time does not yield a high error. At a higher mobile robot speed, however, the localization error becomes too large to locate the mobile robot. Therefore, in high-speed mobile robot operations, instead of using two or more active beacons for localization, only one active beacon and the global features of the mobile robot are used to localize the mobile robot in this research. The two global features are the radius and center of the rotational motion for the differential-driving mobile robot which generally describe motion of the mobile robot and are used for the trace prediction of the mobile robot. In high speed operations the localizer finds an intersection point of this predicted trace and a circle which is centered at the beacon and has the radius of the distance between the mobile robot and the beacon. This new approach resolves the large localization error caused by the high speed of the mobile robot. The performance of the new localization algorithm has been verified through the experiments with a high-speed mobile robot.