• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.6
• /
• pp.758-765
• /
• 1986

The design, fabrication and performance of vertical double diffused power MOSFET (VDMOS) were described. On the antimony (Sb) doped (~7x10**17 cm**-3) silicon substrate (N+), epitaxial layer(N-) was grown. The thickness and the resistivity of this layer were 32\ulcorner and about 12\ulcorner-cm, respectively. The P- channel length which was controlled by sequential P-/N+ double diffuison method was about 1~2 \ulcorner, and was processed with the self alignment of 21 \ulcorner width poly silicon. To improve the breakdown voltage with constant on-resistance (Ron) about 1\ulcorner, three P+ guard rings were laid out around main pattern. With chip size of 4800\ulcorner x4840 \ulcorner, the VDMOS has shown breakdown voltage of 410~440V, on-resistance within 1.0~1.2\ulcornerand the current capablity of more than 5A.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2004.04a
• /
• pp.192-210
• /
• 2004

Application methods of chemicals were investigated tn minimize strength reduction of corrugated boards under the high humidity environment encountered in the cold chain system. Starch insolubilizers were introduced in the starch solution preparation of the Stain hall method and their insolubilization effect of starch binder were estimated. The performance of water repellent agents(WRA) and moisture proof agents(MPA) were evaluated in terms of water and moisture resistance. And effects of the combination of the chemicals and the coating method were also examined. Addition of the polyamine polyamide insolubilizer to the main part in the Stain hall process improved the binding force and water resistance of starch, which contributed to minimize the strength reduction of paper under the high humidity environment. AZC and Glyoxal type insolubilizers could not be used in the experiment due to an excessively increased viscosity of starch solution and the poor stability. Conventional WRA treatment to the base paper enhanced water and moisture resistance very slightly even though water repellency of the paper reached R10 by the treatment. MPA showed excellent performance than WRA not only in water and moisture resistance but in water repellency. Double coating on paper with MPA was more effective than the single coating at the same coating weight. A newly developed MPA showed excellent performance and runnability only by a single coating instead of a double coating.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.2
• /
• pp.60-69
• /
• 2004

Application methods of chemicals were investigated to minimize strength reduction of corrugated boards under the high humidity environment encountered in the cold chain system. Starch insolubilizers were introduced in the starch solution preparation of the Stein hall method and their insolubilization effect of starch binder were estimated. The performance of water repellent agents(WRA) and moisture proof agents(MPA) were evaluated in terms of water and moisture resistance. And effects of the combination of the chemicals and the coating method were also examined. Addition of the polyamine polyamide insolubilizer to the main part in the Stein hall process improved the binding force and water resistance of starch, which contributed to minimize the strength reduction of paper under the high humidity environment. AZC and Glyoxal type insolubilizers could not be used in the experiment due to an excessively increased viscosity of starch solution and the poor stability. Conventional WRA treatment to the base paper enhanced water and moisture resistance very slightly even though water repellency of the paper reached R10 by the treatment. MPA showed excellent performance than WRA not only in water and moisture resistance but in water repellency. Double coating on paper with MPA was more effective than the single coating at the same coating weight. A newly developed MPA showed excellent performance and runnability only by a single coating instead of a double coating.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.1140-1143
• /
• 2002

This work describes the effect of conducting composite on the characteristics of electric double layer capacitor. The cell, which was fabricated with conducting composite consisted of 50 wt.% of SPB and 50 wt.% of VGCF, exhibits the higher specific capacitance, the lower resistance and the better rate capability than those of the cells fabricated with each single electronic conductor. These enhanced properties could be related with the dense structure of electrode.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.9
• /
• pp.32-39
• /
• 2003

Pulse electrochemical machining process with high or low current density may produce a non-lustrous surface on workpiece surface. The usual polishing process to remove a black layer from the surface has been hand polish the part. But the milli-to-micro meter scale structure formed by the electrochemical machining process may be destroyed while polishing process. The application of ultra short voltage pulses based on the analysis of electrical double layer charging process allows high resolution electrochemical machining and polishing. This technique was based on the specific polarization resistance from the comparison of ideal and experimental potential variation during short voltage pulses.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.50 no.1
• /
• pp.38-44
• /
• 2001

For double-circuit transmission line systems, an accurate digital distance relaying algorithm immune to the reactance effect is proposed. The apparent impedance calculated by the distance relay is influenced by the combined reactance effect of the fault resistance and the load current as well as the mutual coupling effect caused by the zero-sequence current of the adjacent parallel circuit. To compensate the magnitude and phase of the estimated impedance, this algorithm uses phase angle difference between the zero(positive) sequence of the both side of the system seperated by the fault point. The impedance measuring algorithm presented used a current distribution factor to compensate mutual coupling effect instead of the collected zero-sequence current of the adjacent parallel circuit.

• Journal of Microbiology and Biotechnology
• /
• v.30 no.8
• /
• pp.1180-1183
• /
• 2020

The prevalence and characterization of plasmid-mediated quinolone resistance (PMQR) determinants in ciprofloxacin-resistant Escherichia coli isolated from a Korean commercial layer farm were studied. A total of 45 ciprofloxacin-resistant E. coli isolates were recovered and all isolates were multidrug-resistant. Eight isolates have the PMQR genes aac(6')-Ib-cr, qnrS1, and qnrB4, and seven isolates exhibited double amino acid exchange at both gyrA and parC, and have high fluoroquinolone minimum inhibitory concentrations. Five transconjugants demonstrated transferability of PMQR and β-lactamase genes and similar antimicrobial resistance. Because PMQR genes in isolates from commercial layer chickens could enter the food supply and directly affect humans, control of ciprofloxacin resistance is needed.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.9
• /
• pp.605-610
• /
• 1999

An SOI(Silicon-On-Insulator) LD(Lateral Double-diffused)MOS with a recessed source structure is proposed to improve the on-resistance and the breakdown voltage. The recessed source structure can decrease the on-resistance by reducing the path of electron current, also increase the breakdown voltage by extending the effective length of gate field plate. Simulation results by TSUPREM4 and MEDICI have shown that the on-resistance of the LDMOS with a recessed source was 26% lower than conventional LDMOS. The breakdown voltage of proposed device was found to be 45V while that of conventional device was 36.5 V. At the same breakdown voltage of 36.5V, the on-resistance of the LDMOS with a recessed source was 41% lower than that of conventional structure.

• Structural Engineering and Mechanics
• /
• v.58 no.3
• /
• pp.555-576
• /
• 2016

In this paper an efficient approach is introduced for design and analysis of double-layer grids including both geometrical and material nonlinearities, while the results are compared with those considering material nonlinearity. Optimum design procedure based on Enhanced Colliding Bodies Optimization method (ECBO) is applied to optimal design of two commonly used configurations of double-layer grids. Two ranges of spans as small and big sizes with certain bays of equal length in two directions are considered for each type of square grids. ECBO algorithm obtains minimum weight grid through appropriate selection of tube sections available in AISC Load and Resistance Factor Design (LRFD). Strength constraints of AISC-LRFD specifications and displacement constraints are imposed on these grids.

• Steel and Composite Structures
• /
• v.22 no.5
• /
• pp.1141-1162
• /
• 2016

Concrete-filled double skin steel tube (CFDST) beam-columns are widely used in industrial plants, subways, high-rise buildings and arch bridges. The CFDST columns have the same advantages as traditional CFT members. Moreover, they have lighter weight, higher bending stiffness, better cyclic performance, and have higher fire resistance capacities than their CFT counterparts. The scope of this study is to develop finite element models that can predict accepted capacities of double skin concrete-filled tube columns under the combined effect of axial and bending actions. The analysis results were studied to determine the distribution of stresses among the different components and the effect of the concrete core on the outer and inner steel tube. The developed models are first verified against the available experimental data. Accordingly, an extensive parametric study was performed considering different key factors including load eccentricity, slenderness ratio, concrete compressive strength, and steel tube yield strength. The results of the performed parametric study are intended to supplement the experimental research and examine the accuracy of the available design formulas.