• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.231-234
• /
• 2009

The effects of annealing temperature and time on mechanical properties and microstructures were already investigated in cold drawn pearlitic steel wires. During annealing, the increment of the tensile strength at low temperatures found to be due to age hardening, while the decrease in the tensile strength at high temperatures was attributed to age softening, involving the spheroidization of lamellar cementite and recovery of lamellar ferrite. Since Between increase of tensile strength and the occurrence of the delamination would be closely related to the dissolution of cementite, the increase of drawing strain by lower annealing temperature caused the between higher tensile strength and the easier occurrence of the delamination in cold drawn pearlitic steel wires.

• Advances in materials Research
• /
• 제1권1호
• /
• pp.83-92
• /
• 2012

The effect of under-bump-metallization (UBM) on electromigration was investigated at temperatures ranging from $135^{\circ}C$ to $165^{\circ}C$. The UBM structures were examined: 5-${\mu}m$-Cu/3-${\mu}m$-Ni and $5{\mu}m$ Cu. Experimental results show that the solder joint with the Cu/Ni UBM has a longer electromigration lifetime than the solder joint with the Cu UBM. Three important parameters were analyzed to explain the difference in failure time, including maximum current density, hot-spot temperature, and electromigration activation energy. The simulation and experimental results illustrate that the addition 3-${\mu}m$-Ni layer is able to reduce the maximum current density and hot-spot temperature in solder, resulting in a longer electromigration lifetime. In addition, the Ni layer changes the electromigration failure mode. With the $5{\mu}m$ Cu UBM, dissolution of Cu layer and formation of $Cu_6Sn_5$ intermetallic compounds are responsible for the electromigration failure in the joint. Yet, the failure mode changes to void formation in the interface of $Ni_3Sn_4$ and the solder for the joint with the Cu/Ni UBM. The measured activation energy is 0.85 eV and 1.06 eV for the joint with the Cu/Ni and the Cu UBM, respectively.

• 설비공학논문집
• /
• 제18권7호
• /
• pp.596-602
• /
• 2006

Ice adhesion and blockage problems have been issued in continuous ice slurry making process. So we composed continuous ice slurry making device using a commercial small plate heat exchanger (PHX), and investigated character of ice formation. An experiment of ice formation was peformed with an aqueous solution of ethylene glycol 7 mass%. In the experiment, the effect of the pressurization on ice slurry formation during the cooling process was investigated. The pressurization test for the aqueous solution was performed by setting valves at the PHX inlet and outlet. At the results, the time of continuous ice formation increased as the pressure of the plate heat exchanger increased for cooling temperature of $-5^{\circ}C$. Also continuous ice formation at the cooling temperature of $-7^{\circ}C$ showed a possibility. It was found that the pressurization may contribute to suppress the dissolution of supercooled aqueous solution in the PHX.

• Corrosion Science and Technology
• /
• 제21권1호
• /
• pp.9-20
• /
• 2022

The aim of this paper is to study corrosion inhibition of Aluminum with Capparis decidua extract. The study was performed in a 1.0 M solution of hydrochloric acid (HCl) and was monitored both by measuring mass loss and by using electrochemical and polarization methods. A scanning electron microscopy (SEM) technique was also applied for surface morphology analysis. The results revealed high inhibition efficiency of Capparis decidua extract. Our data also determined that efficiency is governed by temperature and concentration of extract. Optimum (88.2%) inhibitor efficiency was found with maximum extract concentration at 45 o C. The results also showed a slight diminution of aluminum dissolution when the temperature is low. Based on the Langmuir adsorption model, Capparis decidua adsorption on the aluminum surface shows a high regression coefficient value. From the results, the activation enthalpy (∆H#) and activation entropy (∆S#) were estimated and discussed. In conclusion, the study clearly shows that Capparis decidua extract acted against aluminum corrosion in acidic media by forming a protective film on top of the aluminum surface.

• 한국환경과학회지
• /
• 제27권10호
• /
• pp.901-906
• /
• 2018

Water and oxygen are two of the most essential molecules for many species on earth. Their unique properties have been studied in many areas of science. In this study, the interaction of water and oxygen molecules was observed at the nano-scale. Using molecular dynamics, a water droplet with 30,968 water molecules was simulated. Then, 501 oxygen molecules were introduced into the domain. A few oxygen molecules were attracted to the surface of the water droplet due to van der Waals forces, and some oxygen molecules actually entered the water droplet. These interactions were visualized and quantified at four temperatures ranging from 280 to 370 K. It was found that at high temperatures, there was a higher possibility of the oxygen molecules penetrating the water droplet than that at lower temperatures. However, at lower temperatures, oxygen molecules were more likely to be found interacting at the surface of the water droplet than at high temperatures.

• 열처리공학회지
• /
• 제33권4호
• /
• pp.185-192
• /
• 2020

In this study, materials characterization of pure copper and copper based carbon nano-tube composite prepared by powder metallurgy method were investigated. Prior to evaluate materials characterization, spark plasma sintering processing variables such as sintering temperature, pressure, thickness and diameter of compacts was optimized to ensure the microstructure and materials property of pure Cu and Cu-CNT composite. In addition, corrosion behavior of Cu-based CNT composite produced by powder sintering method was investigated. It was confirmed from this study that the corroded surfaces of the composite shows less dissolution compared with pure copper in 3.5 wt% NaCl solution. The measured corrosion current density (I_corr) indicates improved corrosion property of Cu based composite containing small additions of CNTs in chloride containing media. Micro-galvanic activity between Cu and CNT was not observed in given sintering condition.

• 한국재료학회지
• /
• 제14권7호
• /
• pp.457-461
• /
• 2004

The thermomechanically treated $Ti-45.4\%Al-4.8\%Nb(at\%)$ alloy was oxidized between 800 and $1000^{\circ}C$ in air, and the oxidation characteristics were studied. The dissolution of Nb in the oxide scale was observed from the TEM study. The Pt marker test revealed that the oxidation process was controlled by the outward diffusion of Ti ions and the inward diffusion of oxygen ions. During oxidation, the evaporation of Nb-oxides was found to occur to a small amount. Niobium tended to pile-up at the lower part of the oxide scale, which consisted primarily of an outer $TiO_2$ layer, and an intermediate $Al_{2}O_{3}-rich$ layer, and an inner mixed layer of ($TiO_{2}+Al_{2}O_{3}$).

• 한국임상약학회지
• /
• 제1권1호
• /
• pp.23-30
• /
• 1991

The sustained-release beads containing terbutaline sulfate (TBS) were prepared by rotogranulation method. The drug was dusted on the non-pareil seeds in a CF-granulator. The sustained-release beads were obtained by coating the active beads with ethylcellulose or $Eudragits^{(R)}$, using in any case the same granulator employed for active beads preparation. The release characteristics of sustained-release beads were examined in vitro by rotating basket method applied to $Bricanyl^{(R)}$ durules which is a sustained-release TBS matrix tablet. The release of terbutaline from the beads in vitro was first-order, and the release rate was dependent on both the coat weight ratio and membrane hydrophilicity. Both surfaces of the beads before and after dissolution were smooth. The drug release pattern from the beads could be thought the diffusion through the polymer membrane. The release rate and the surface of the beads stored for 3 years at room temperature were the same with those of the initial beads.

• 공업화학
• /
• 제16권1호
• /
• pp.68-73
• /
• 2005

층상 실리케이트를 주형으로 이용하여 실리케이트의 층간에 pyrolized fuel oil (PFO)를 삽입하고 열분해시킨 후 실리케이트 골격을 용출 제거함으로써 다공성 층상카본을 제조하였다. 층상카본의 입자모양은 층상실리케이트 주형과 유사한 판상 형태이며, d-spacing은 0.78~0.82 nm로 일정한 값을 나타내었다. 실리케이트와 PFO의 혼합비율과 열처리 온도, 열처리 시간에 따른 비표면적은 $30{\sim}576m^2/g$로 크게 다른 값을 나타내었다.

• 한국분말재료학회지
• /
• 제21권2호
• /
• pp.114-118
• /
• 2014

In this study, an aluminum oxide layer for sealing treatment of nano-diamond powder was synthesized by anodizing under constant current. The produced pore size and oxide thickness were investigated using scanning electron microscopy. The pore size increased as the treatment time increased, current density increased, sulfuric acid concentration decreased, which is different from the results under constant voltage, due to a dissolution of the oxide layers. The oxide layer thickness by the anodizing increased as temperature, time, and current density increased. The results of this study can be applied to optimize the sealing treatment process of nano-diamond particles of 4-10 nm to enhance the resistances of corrosion and wear of the matrix.