• 한국수자원학회논문집
• /
• 제56권1호
• /
• pp.1-9
• /
• 2023

현재까지는 연중 하천유량의 관리기간은 홍수기와 비홍수기로 구분하고, 관리해야 할 유량의 범위는 갈수량에서 홍수량까지로 폭넓게 규정하고 있다. 본 연구에서는 4대강 8개 지점의 장기간 일평균유량 자료를 이용하여1년을 유량의 분산과 평균이 동질한 기간들로 구분하고, 기간별 유량의 평균과 표준편차를 이용하여 유량의 관리범위를 설정하는 방안을 제시한다. 연구결과, 연중 관리기간은 지점에 따라 차이는 있으나 홍수기 이전, 홍수기, 홍수기 이후로 구분할 수 있었으며, 기간을 세분화하면 최소유량에 대한 최대유량의 비도 낮아지는 것을 알 수 있었다. 또한, 연중 일평균유량이 갈수량 이상 홍수량 이하가 되도록 기간별 일평균유량의 관리범위를 기간별 일평균유량의 평균 ±표준편차로 설정하는 방안도 제시하였다.

• 한국분말재료학회지
• /
• 제24권2호
• /
• pp.102-107
• /
• 2017

Porous polytetrafluoroethylene (PTFE) thin films are fabricated by spin-coating using a dispersion solution containing PTFE powders, and their crystalline properties are investigated after thermal annealing at various temperatures ranging from 300 to $500^{\circ}C$. Before thermal annealing, the film is densely packed and consists of many granular particles 200-300 nm in diameter. However, after thermal annealing, the film contains many voids and fibrous grains on the surface. In addition, the film thickness decreases after thermal annealing owing to evaporation of the surfactant, binder, and solvent composing the PTFE dispersion solution. The film thickness is systematically controlled from 2 to $6.5{\mu}m$ by decreasing the spin speed from 1,500 to 500 rpm. A triboelectric nanogenerator is fabricated by spin-coating PTFE thin films onto polished Cu foils, where they act as an active layer to convert mechanical energy to electrical energy. A triboelectric nanogenerator consisting of a PTFE layer and Al metal foil pair shows typical output characteristics, exhibiting positive and negative peaks during applied strain and relief cycles due to charging and discharging of electrical charge carriers. Further, the voltage and current outputs increase with increasing strain cycle owing to accumulation of electrical charge carriers during charge-discharge.

• 한국물환경학회지
• /
• 제26권3호
• /
• pp.532-539
• /
• 2010

The synthetic unit hydrograph is developed and verified using Nash model and characteristic velocities considering geomorphological dispersion in this present study. Application watersheds are selected 5 subwatersheds of Bocheong basin. The mean and variance of hillslope and stream path length are estimated in each watershed with GIS. Characteristic velocities are calculated using estimated path lengths and moment characteristics of rainfall-runoff data. Characteristic velocities of random devised 7 ungauged watersheds are estimated through regional analysis of chracteristic velocities in guaged watershed. And Nash model parameters and IUH are derived using characteristic velocities and path length in the gauged and ungauged watershed. The result to compare of IUH about gauged watershed and random devised ungauged watershed in application watershed presents coherently hydrologic response characteristics that peak discharge is reduced and peak time is extended. In conclusion, Developed synthetic unit hydrograph in this study expects that it is useful method to estimate runoff discharge for managing of water pollution in ungauged watershed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.153-153
• /
• 2008

Practical application of single-walled carbon nanotubes (SWCNTs) qualified as a promising material has been limited by either poor dispersion or their insolubility in aqueous or organic media due to formation of bundling by relatively high surface energy. Thus, major attention to overcome this issue has been paid at surface modification of CNTs by functionalization, but this introduces defects to the sidewall of CNTs, consequently perturbing the inherent electronic and optical properties. Therefore, using surfactants is a general approach to disperse SWCNTs with lower damages by which bundled nanotubes could be dispersed up to the level of individuals or small bundles. Here, we have investigated various surfactants for their efficiency in dissolving purified SWCNTs produced by arc discharge in deionized water. To compare the surfactants respectively, we have determined the least amount of each surfactant to suspend the nanotubes under optimized experimental conditions(CNT amount, sonication power, and centrifugation speed, etc.) set on the basis of the most common surfactant (sodium dodecyl sulfate, SDS) and discussed the qualitative and quantitative characterization of SWCNT dispersions by UV-Vis absorption spectroscopy. Quantitative aspect about nanotube dispersion was that in particular N-methyl-2-pyrrolidone (NMP) and sodium dodecylbenzene sulfonate (NaDDBS) were found to be effective in dispersing individual tubes.

• 한국대기환경학회지
• /
• 제16권4호
• /
• pp.351-362
• /
• 2000

To set the similarity conditions between a prototype usually in the field and its reduced-scale model is a crucial part in model tests. No technique is available to keep perfect similarity for this procedure so far. The experimental work using a wind tunnel is not exceptional. based on the field measurements, the effect of stack parameters and wind conditions on the dispersion of stack plume has been investigated in the laboratory. in this paper intensive methodology is focused on matching these similarities. Due to the limitations to keep perfect similarity conditions some simplifications are involved in common. In this study geometric conditions and kinematic conditions using Froude number and Reynolds number have been con-sidered to keep the similarity conditions required. From the tests it is found that the critical Reynolds number (Recrit) is 2,700 when the height of stack discharge is 50mm. The dispersion has a similar trend for the higher Reynolds number than the critical Reynolds number. It is also found that different Froude number does not make any significant influence for the normalized tracer gas concentrations at the recipient providing the same ratio of the wind speed to the discharge speed. No significant effect of stack diameter is observed in the normalized tracer gas concentrations with the same Frounde number. The similarity conditions therefore used in this study are reliable to simulate the conditions in prototype into the wind tunnel tests.

• 한국전기전자재료학회논문지
• /
• 제20권11호
• /
• pp.959-964
• /
• 2007

To investigate the influence of partial discharge(PD) distribution characteristics due to various defects on the power cable joints interface, we used the K-means clustering method. As the result of PD number(n) distribution analyzing on $\Phi-n$ graph, the phase angle($\Phi$) of cluster centroid shifted to $0^{\circ}\;and\;180^{\circ}$ increasing with applying voltage. It was confirmed that the PD quantify(q) and euclidean distance of centroid were increased with applying voltage from the centroid distribution analyzing of $\Phi-q$ plane. The dispersion degree was increased with calculated standard deviation of the $\Phi-q$ cluster centroid. The PD number and mean value on $\Phi-q$ graph were some different by electric field concentration with defect types.

• Korean Journal of Hydrosciences
• /
• 제3권
• /
• pp.61-79
• /
• 1992

In oder to predict the dispersion of a thermal discharge with strong turbulent and buoyant effects, the development of a numerical model using turbulence model and its application are significantly increased. In this study, a three-dimensional steady-state model for the surface discharge heated water into quiescent water body is developed. For the model closure of turbulent terms the four-equation turbulence model is used. For economic mumerical simulation, the elliptic governing equations are transformed to the partially parabolic equations. In general, the simulated results by the present model agree well with the experimental results by Pande and Rajratnam (1977). The model characteristics are presented in comparison with the predicted results from the two-eqauation turbulence model by McGuirk and Rodi (1979).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 일렉트렛트 및 응용기술
• /
• pp.170-176
• /
• 2002

In this papers, we proposed the feature extraction method due to partial discharge type of transformers. For wavelet transform, Daubechie's filter is used, we can obtain wavelet coefficients which is used to extract feature of statistical parameters (maximum value, average value, dispersion, skewness, kurtosis) about acoustic emission signal generated from each partial discharge type. The defects which could occur in a transformer were simulated by using needle-plane electrode, IEC electrode and Void electrode. Also, these coefficients are used to identify signal of partial discharge type electrode fault in transformer. As a result, from compare of acoustic emission amplitude and acoustic average value, we are obtained results of IEC electrode> Void electrode> Needle-Plane electrode. otherwise, In case of skewness and kurtosis, we are obtained results of Needle-Plane electrode electrode> Void electrode> IEC electrode.

• 한국지리정보학회지
• /
• 제5권2호
• /
• pp.25-33
• /
• 2002

위성영상과 수치모델을 이용하여 낙동강유출 부유토사의 확산범위를 구해 낙동강유출수의 영향권을 간접적으로 이해하고자 하였다. 수심을 적분한 2차원모델을 이용하여 유속장 계산 결과를 보면 창조시 부산에서 진해만과 거제도방향으로 흐름이 보였으며, 낙조시에는 창조시와 반대의 흐름을 보였다. 유속의 크기는 외양이 연안보다 크게 나타났다. 12시간 조시 평균에 의한 잔차류는 남서에서 북동방향의 흐름이 우세하게 나타났으며, 가덕도 동안에서는 동쪽으로 향하는 흐름이 나타났다. 이와 같은 유속장을 기반으로 부유토사의 확산 정도를 라그랑지 방법인 수치추적자 방법을 이용하여 구했다. 그 결과, 낙동강유출 부유토사의 범위는 가덕도 동안에서 부산방향으로 나타났다. SeaWiFS와 LANDSAT위성자료로 추정한 낙동강 유출부유토사의 확산범위는 수치모델의 결과와 비슷한 양상을 나타내었다.

• 물과 미래
• /
• 제23권4호
• /
• pp.487-497
• /
• 1990

원자력·화력, 제철소 등의 임해공업시설로부터 온수 방출의 확산에 대한 정성, 정량적 예측은 환경관리 및 냉각수 취·배수로 설계에 매우 중요하다. 본 연구는 난류 및 부력효과가 강한 온배수의 주요 물리적 특성을 규명하고 실무에 많이 사용되고 있는 MIT 및 PDS 적분모델의 비교평가를 실시하였다. 일반적으로 MIT 및 PDS 모델은 성층화되지 않은 수역에서 주위수 및 제트 방출각도를 고려하여 온배수 거동을 산정하는 모델이다. 해석결과는 그 구성의 상이성에 의해 매우 다름이 규명되어, 온배수의 정확한 산정을 위해서는 난류모델을 이용한 수치모델의 개발 및 이의 적용이 요구된다.