• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.1015-1018
• /
• 2005

In this paper, we introduce about a new class to analysis of partial discharge signal based on Fuzzy model. We can early diagnose life of power cable through detection of partial discharge signal. However, partial discharge signal detector is difficult because of partial discharge signal is very non-linear. Also, it is very difficult work that separate partial discharge signal from noise. We constructed partial discharge accumulation detection system that use Labview for detection of non-linear partial discharge signal. And analyzed partial discharge signal that is detected by Labview system utilizing Fuzzy model.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 2005년도 추계학술대회 학술발표 논문집 제15권 제2호
• /
• pp.440-443
• /
• 2005

In this paper, we introduce about a new class to analysis of partial discharge signal based on Fuzzy model. We can early diagnose life of power cable through detection of partial discharge signal. However, partial discharge signal detector is difficult because of partial discharge signal is very non-linear. Also, it is very difficult work that separate partial discharge signal from noise. We constructed partial discharge accumulation detection system that use Labview for detection of non-linear partial discharge signal. And analyzed partial discharge signal that is detected by Labview system utilizing Fuzzy model.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1382-1383
• /
• 2008

In this paper, we have studied for analysis of the partial discharge(PD) signal based on fuzzy algorism. Partial discharge signal detector is difficult because of partial discharge signal is very non-linear. Also, it is very difficult work that separate partial discharge signal from noise. We constructed partial discharge accumulation detection system that use Labview for detection of non-linear partial discharge signal. And analyzed Partial discharge signal that is detected by Labview system utilizing Fuzzy model.

• 전기학회논문지
• /
• 제63권3호
• /
• pp.409-413
• /
• 2014

GIS partial discharge that occurred in the UHF band signal is effectively detected by the method to IEC60270 5pc the apparent minimum discharge can be detected over the GIS arrangement of the sensor interior and exterior of the UHF in accordance with the optimized position signal by considering the damping ratio is selected so that the signals can be obtained to be mounted. 362kV, 800kV GIS is installed on the internal and external sensors are UHF band signal attenuation is set by measuring the reference value, but the operation, 170kV case 362kV, 800kV on the basis of the measurement data and to be installed and operated. When 170kV per 1Bay by installing the built-in sensor 1 for detecting a partial discharge signal, But, GIS signal attenuation is large in the case of an internal partial discharge signal is not detected in some cases. Where the attenuation is great UHF signal of the sensor by increasing the quantity of partial discharge signals were acquired to allow relocation. The greater the spacing between the sensor and the sensor is applied simplifies the installation and reduces the cost in terms of maintenance of appropriate optimal position is calculated to detect the partial discharge signal is needed. Thus 170kV GIS signal power attenuation of a partial discharge by measuring the UHF sensor, and by relocating the proper position is calculated in accordance with the sensor signal decay rate and minimize the error of omission in detecting a partial discharge signal was optimized.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.581-584
• /
• 2000

Generally, it is known that many partial discharges are occurred in one voltage cycle. In this case, it is not easy to distinguish between ultrasonic signals caused by the partial discharge. We describes a pattern of the ultrasonic signal by the partial discharge in transformer. The test setup for ultrasonic signal measurement was to simulate a internal partial discharge by using a needle to plane electrodes. We compared the number of partial discharge and ultrasonic signal in one voltage cycle. The results showed that it was possible to distinguish between ultrasonic signals by analysing partial discharge detection method and ultrasonic signal on time domain.

• 조명전기설비학회논문지
• /
• 제15권4호
• /
• pp.23-30
• /
• 2001

본 연구에서는 교류유전체장벽형 코로나방전을 이용하여 선대원통형 전극구조의 방전리액터내의 NO입자의 방전 Image와 형광방출파장대역[236[nm], 247[nm], 259[nm]에서의 수평방향과 수직방향의 신호강도를 ICCD카메라를 이용하여 측정하였다. 또한 방전메카니즘을 알기 위해서 방전진전시간에 따른 방전 Image와 신호강도 측정을 행하였다. NO입자의 수평과 수직방향의 신호강도는247[nm]대역에서 가장 큰 것을 확인 할 수 있었으며, 방전진전시간에 따른 수평과 수직방향의 신호강도는 큰 변화가 없었다. 특히 측정된 데이터로부터 반응장치 내부에서 일어나는 현상의 Image와 형광방출파장의 신호강도를 비교할 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.874-877
• /
• 2002

The optogalvanic signals were measured using hollow cathode discharge tube with argon as buffer gas at change of discharge currents. A change of ionization rate due to electron collision causes an increase or decrease of the electric conductivity. This change in electric conductivity generates the optogalvanic signal. We conclude that optogalvanic signal has close relation with the lowest metastable atoms density at low current.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권11호
• /
• pp.622-626
• /
• 2000

In this paper, an optical fiber sensor(OF sensor) utilizing the principal of Sagnac interferometer was proposed to detect the discharge signals. The needle-sphere electrode system in insulating oil generated the signals. The performance of OF sensor was checked by sinusoidal calibration signal generated by PZT actuator at 198KHz. The detected discharge signals consisted of acoustic signal and the electrical noise. The noise signal could be removed by digital low pass filter. It was demonstrated that the OF sensor in this research had a possibility to detect the discharge signals in power apparatus.

• 전기학회논문지
• /
• 제59권4호
• /
• pp.728-732
• /
• 2010

GIS(Gas insulated switching gear) is power equipment with excellent dielectric strength and is economy merit in high confidence and stability. Recently, because equipment of GIS was occurring problem of confidence used for a long time, partial discharge on-line diagnosis systems have been importantly recognized. Partial discharge (PD) detection is an effective means for monitoring and evaluation of dielectric condition of gas insulated system (GIS). The ultra-high-frequency (UHF) PD detection technique can detect and locate the PD sources inside GIS by detecting electromagnetic wave emitted from PD source. Therefore, real-time diagnostic system using UHF detection method has been developed for this application is being expanded gradually. However, the signal of partial discharge occurring in SF6 gas is very weak and susceptible to external noises which mainly consist of PD in air. Thus, it is important to distinguish the PD in SF6 gas more sensitively from the external noises. Unfortunately, these external noise signals and the partial discharge signals have very similar characteristics. Therefore, to solve this problem, we need the signal processing method for distinguish partial discharge signals with external noise signals for improvement of SNR(signal to noise ratio) and sensitivity. In this paper, we proposed internal signal processing method for removing external noise signals with built-in pre.amplifier and frequency conversion circuit.

• 한국음향학회지
• /
• 제21권7호
• /
• pp.614-623
• /
• 2002

본 논문에서는 전력설비의 열화로 발생되는 부분방전 음압 검출을 위해 간섭계형 광섬유 센서를 제작하고 방전 음압을 측정하였다. 광섬유 센서는 아크릴과 알루미늄에 광섬유를 수회 감은 맨드릴형으로 선택하였으며, 간섭계는 Sagnac간섭계 및 Mach-Zehnder 간섭계를 선택하여 실험하였다. 피에조 (PZT)를 이용하여 구성된 광섬유 간섭계의 적합성을 확인하였다. 방전 음압 발생장치는 절연유 내에 방전 모의셀을 설치하여 방전 음압을 발생시키고, 광섬유 센서로 방전신호를 검출하였다. 실험결과 Sagnac 간섭계가 Mach-Zehnder간섭계보다 방전 음압을 보다 안정적으로 검출함을 확인하였으며, Sagnac 간섭계 센서가 방전 음압 검출에 적합함을 확인하였다.