• Transactions on Electrical and Electronic Materials
• /
• v.9 no.4
• /
• pp.137-142
• /
• 2008

The parasitic resistance is studied to silicon/metal contact junction for improving device performance and to lower contact/serial resistance silicide in natural sequence. In this paper constructs the stepwise Ni silicide process for parasitic resistance reduction for silicon/metal contact junction. We have investigated multi-step Ni silicide on SiGe substrate with stepwise annealing method as an alternative to compose more thermally reliable Ni silicide layer. Stepwise annealing for silicide formation is exposed to heating environment with $5^{\circ}C/sec$ for 10 seconds and a dwelling for both 10 and 30 seconds, and ramping-up and the dwelling was repeated until the final annealing temperature of $700\;^{\circ}C$ is achieved. Finally a direct comparison for single step and stepwise annealing process is obtained for 20 nm nickel silicide through stepwise annealing is $5.64\;{\Omega}/square$ at $600\;^{\circ}C$, and it is 42 % lower than that of as nickel sputtered. The proposed stepwise annealing for Ni silicidation can provide the least amount of NiSi at the interface of nickel silicide and silicon, and it provides lower resistance, higher thermal-stability, and superior morphology than other thermal treatment.

• 연구논문집
• /
• s.34
• /
• pp.29-38
• /
• 2004

The objective of this study is to investigate the pressure drop and heat transfer characteristics of the micro-fin tubes before and after the tube-expansion process. Test tubes are single-grooved micro-fin tubes made of copper with an outer diameter of 9.52 mm before the tube-expansion. The direct heating method is applied in order to make the refrigerant evaporated in the micro-fin tubes. The test ranges of the heat flux, mass flux, and the saturation pressure are 5 to 15kW/$m^2$, 100 to 200 kg/$m^2s$ and 540 to 790 kPa, respectively. The effects of the mass flux, heat flux, and the saturation pressure of the refrigerant on the pressure drop and the heat transfer are presented for the refrigerant R22. In the test conditions of this study, the heat transfer coefficient for the micro-fin tube after the tube-expansion is about 16.5% smaller than that before the tube-expansion because the fin height of micro-fin is reduced and the fin shape becomes flatter. The micro-fin tube after the tube-expansion has about 7.7% greater average pressure drop than that before the tube-expansion process.

• Journal of Ocean Engineering and Technology
• /
• v.9 no.1
• /
• pp.101-110
• /
• 1995

In SMA(Shape Memory Alloy), the degradation by fatigue is one of the most important problems to be overcome, when SMA is used for robot-actuator materials. The actuator is operated repetitively for long time and its repeating operation develops the fatigue degradation of SMA. The fatigue degradation changes the transformation temperature and deformation behavior and results in inaccurate operation and deformation which results form repeating operation is to be investigated in advance and the scheme to resolve those problems have to be made for the design of actuator. In this paper, for the improvement of the fatigue degradation by repetive movement and better control of the correct movement by the stability of martensite transformation in the development of Robots actuator, Pre-strain(0, 1.5, 5, 8%) are loaded in the specimens and fatigue testing were carried out by the method of heating and cooling in direct condition. From the results of these experiments, the effect on pre-strain which affect the transformation characteristic and fatigue degradation phenomena were correctly investigated.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.8 s.239
• /
• pp.927-933
• /
• 2005

Boiling heat transfer characteristics of liquid nitrogen in a stainless steel plain tube and wire coil inserted tubes were investigated. The test tubes, which had an inner diameter of 10.6 m and a length of 1.65 m, were horizontally located. Five wire coils having different pitch and thickness were inserted into the plain tube. The pitches of the wire coils were 18.4, 27.6, and 36.8 m, and the thickness was 1.5, 2.0, and 2.5 mm respectively. Tests were conducted at a saturation temperature of $-191^{\circ}$, mass fluxes from 58 to 105 kg/$m^2s$, and heat fluxes from 22.5 to 32.7 kw/$m^2$. A direct heating method was used to apply heat to the test section. The boiling heat transfer coefficients of liquid nitrogen were represented as a function of vapor quality, which showed significant drop at the dryout vapor quality. The maximum heat transfer enhancement using the wire coil inserted tubes over the plain tube was $174\%$ for 'Wire 3' having a thickness of 2.5 mm and a pitch of 18.4 mm.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.4
• /
• pp.290-299
• /
• 2008

Evaporation heat transfer characteristics of $CO_2$/propane mixtures in horizontal smooth and micro-fin tubes have been investigated by experiment. The experiments were carried out for several test conditions of mass fluxes, heat fluxes, compositions of $CO_2$/propane refrigerant mixtures and tube geometries. Direct heating method was used for supplying heat to the refrigerant where the test tube was uniformly heated by electric current which was applied to the tube wall. Heat transfer coefficient data during evaporation process of $CO_2$/propane mixtures were measured for 5 m long smooth and micro-fin tubes with outer diameters of 5 mm, respectively. The tests were conducted at mass fluxes of 318 to 997 $kg/m^2s$, heat fluxes of 6 to 20 $kW/m^2$ and for several mixture compositions (100/0, 75/25, 50/50, 25/75, 100/0 by wt% of $CO_2$/propane). The differences of heat transfer characteristics between smooth and micro-fin tubes for various compositions of $CO_2$/propane refrigerant mixtures and the effect of mass flux, and heat flux on enhancement factor (EF) and penalty factor (PF) were presented.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.104-107
• /
• 2000

Evaporative heat transfer characteristics of carbon dioxide has been investigated. Experiment has been carried out for seamless stainless steel tube with outer diameter of 9.55 mm and inner diameter of 7.75 mm. Direct heating method is used for supplying heat to the refrigerant was uniformly heated by electric current which was applied to the tube wall. The saturation temperature of refrigerant is calculated from the measured saturation pressure by using an equation of state. Inner wall temperature was calculated from measured outer wall temperature, accounting for heat generation in the tube and heat conduction through the tube wall. Mass Quality of refrigerant was calculated by considering energy balance in the preheater and the test section. Heat fluxes were set at 12, 16, 20, 23, and $27kW/m^2$, mass fluxes were controlled at 212, 318, 424, and $530 kg/m^2s$, and saturation temperature of refrigerant were adjusted at 0, 3.4, 6.7 and $10.5^{\circ}C$. From this study, heat transfer coefficients of carbon dioxide have been provided with respect to quality for several mass fluxes, heat fluxes. Finally, the experimental results in this study are compared with the correaltion by Gungor and Winterton(1987).

• Textile Coloration and Finishing
• /
• v.26 no.1
• /
• pp.63-70
• /
• 2014

This study has attempted to figure out the effects of the surface heat of perm rods on hair. For this, after forming perm waves, hair damage and its causes have been investigated with a different hair bleach method. If hair was bleached immediately without shampooing after a perm using the heat of rods, great perm waves were formed. However, severe damage was found on the hair because of the heated rods. In addition, when hair was shampooed and dried after the perm, hair bleach was more effective. It has been confirmed that hair was damaged because of high temperature of the surface of the rods. In fact, the heated rods had a direct effect on hair damage. According to these results, it has been confirmed that heat-based perms can accelerate hair damage. Therefore, it is necessary to perform a study on the minimization of the heating of permanent tools.

• Korean Journal of Acupuncture
• /
• v.28 no.4
• /
• pp.137-145
• /
• 2011

Objectives : This research dealt with the content of the hot medicinal compress technique in Donguibogam in order to develope the hot medicinal compress technique as a new therapy technique. Methods : In this research, we searched for the hot medicinal compress treatment in Donguibogam. Results : The hot medicinal compress technique mainly cures the diseases on the body surface and it can be applied to digestive troubles and gynecologic diseases. The hot medicinal compress technique is operated mainly at wound around the affected parts and it is applied to the constitutional symptom at the abdominal region. In the hot medicinal compress technique was used much more with medication, and the herbs used in the treatment consists of hot tastes and the warm characteristics. In the hot medicinal compress method with direct heating the herbs was mainly used. Conclusions : The hot medicinal compress technique is considered as treatment which can be utilized easily and it can be used an easy and useful self-treatment.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.24 no.3
• /
• pp.440-445
• /
• 1995

The antimutagenic effects of juices from green pepper(GP), red pepper leaf(RPL), red pepper(RP) and sweet pepper(SP) were examined by the Ames method using Salmonella typhimurium TA100. The juice supernatants of GP, RPL and RP showed antimutagenic activities against afltoxin B1(AFB1) in Salmonella typhimurium TA 100. The juice supermatants of GP and RPL also exhibited the inhibitory effects(p<0.05) to the mutagenicities induced by N-methyl-N'-nitro-N-nitrosoguanidine(MNNG) and 4-nitro-quinoline-1-oxide(4-NQO). The juice of RP showed antimutagenic activities against indirect mutagen of AFB1, however, the activity was reduced at higher concentration(5.0%), furthermore, as the adding concentration of sample increased to 5.0%, it exhibited slight comutagenicith on direct mutagen of MNNG. Theantimutagenic activities of GP and RPL juices were reduced significantly after heating at 100℃ for 20min, supposing that the antimutagenic compound(s) in the juices were heat labile.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.262-268
• /
• 2008

The present paper dealt with flow heat transfer characteristics of R-410A vaporization in horizontal smooth microchannel. The test sections were made of stainless steel tube with inner diameters of 300 mm and length of 300 mm. The refrigerant was supplied with mass flux range of 260-600 kg/$m^2s$ and applied under operating heat flux range of 5-20 kW/$m^2$ using a direct electric current heating method. The in let saturation temperature was set at $10^{\circ}C$ and vapor quality up to 1.0. The influences of mass flux, heat flux and inner tube diameter on local heat transfer coefficients were presented. Comparison with existing heat transfer coefficient correlations was performed. An improved heat transfer coefficient correlation for refrigerant vaporization in microchannel based on superposition model was developed with a mean deviation of 14.01%.