• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.1-6
• /
• 1998

To achieve fast control action, direct control methods should be used. "Direct Mean Torque Control" (DMTC) combines the good dynamic performance of Direct Torque Control (DTC) with the advantages of inherently constant switching frequency and time equidistant control for implementation in a digital signal processor. Since DMTC is a predictive control algorithm, the model and its correction deserves special investigations. This paper proposes a steady-state Kalman filter which is well suited for fast computation.mputation.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권8호
• /
• pp.514-521
• /
• 2000

This paper presents a direct thrust control scheme for permanent magnet linear synchronous motor(PMLSM) by using digital signal processor(DSP). And a simulation method for the direct thrust control of a permanent magnet linear synchronous motor using the equivalent circuit is presented. The detent force that was obtained by cubic spline method is considered in the simulation. Thrust correction coefficient is utilized to estimate actual thrust on the direct thrust control, which considers the longitudinal end effect due to the finite core length of the permanent magnet linear synchronous motor. The motor self inductance, the initial flux linkage by the permanent magnet is calculated in advance by the finite element analysis, and then the direct control simulation is carried out. As the results, thrust, current and speed are shwon.

• 전기의세계
• /
• 제30권8호
• /
• pp.509-516
• /
• 1981

The optimal control theory is applied to the design of a digital control system for a nuclear reactor. A linear dynamic model obtained at 85% of rated power and a quadratic performance index are used. A minimal order observer used in cascade with the feedback controller is suggested as a state estimator. The total reactor power control is studied in the range of 80% to 100% of rated power, with the steady state and load-following control. The control algorithm considered is suitable for implementation in direct digital control.

• 대한전기학회논문지
• /
• 제40권1호
• /
• pp.31-38
• /
• 1991

A direct digital control technique of a current source using the phase-controlled rectifier is presented. A digital firing technique without sensing the line voltage is proposed. This scheme generates firing pulses directly from error signal between command and output voltage. Thus the phase detection transformers filters and zero-crossing detector are unnecessary. The synchronism is modeled and analized. Also a software synchronization algorithm is presented without a look up table and controls the system in real time with fast dynamic characteristics. Using the single-chip microprocessor 8097BH, the direct digital control is implemented with minimal hardware structure. Using the time-weighted performance index, the optimal discrete IPM control technique is also proposed to control the current of the PCR.

• Spatial Information Research
• /
• 제13권1호
• /
• pp.55-63
• /
• 2005

최근에는 항측기에 GPS/INS 장비를 탑재하여 사진의 촬영과 동시에 외부표정요소를 직접 결정할 수 있는 Direct Georeferencing기술의 개발로 인하여 지상기준점을 최소로 측량하거나 생략이 가능하게 되었다. Direct Georeferencing 기법을 이용하게 되면 외부표정요소를 구하기 위한 전처리 과정을 생략할 수 있다. 따라서 지상기준점을 이용한 사진기준점측량(AT)을 수행하지 않더라도 수치표고모델만 미리 확보되어 있으면 촬영과 동시에 수치정사사진을 생성할 수 있다. 본 연구에서는 촬영과 동시에 GPS/INS에 의해 획득한 외부표정요소와 항공사진을 이용하여 영상매칭에 의하여 수치표고모델(DEM)을 자동 생성하고, 이 결과를 바탕으로 정사사진을 제작하였다. 실제 도화데이터와 Direct Georeferencing 정사영상과의 오차를 평가한 결과, 표준편차가 X는 약 62cm, Y는 약 76cm 정도가 발생하였다. 이 결과는 축적 1:5,000 수치지도의 정확도 요구를 충분히 만족시킬 수 있는 양호한 결과임을 알 수 있다. Direct Georeferencing에 의한 정사영상의 제작방법은 큰 크기의 과대오차가 발생하는 부분을 수작업 또는 반자동으로 해결할 수 있으면 효율적으로 수치지도를 수정/갱신 할 수 있을 것으로 판단된다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.970-973
• /
• 2003

Abstract An idea to redce the direct-path short circuit current of the CMOS digital integrated circuit is present. The sample circuit model of the CMOS digital circuit is the CMOS current-control digital output driver circuit, which are also suitable for the low voltage supply integrated circuits as the simple digital inverter, are present in this title. The circuit consists of active MOS load as the current control source, which construct from the saturated n-channel and p-channel MOSFET and the general CMOS inverter circuits. The saturated MOSFET bias can control the output current and the frequency response of the circuit. The experimental results show that lower short circuit current control can make the lower frequency response of the circuit.

• Journal of Power Electronics
• /
• 제11권2호
• /
• pp.113-119
• /
• 2011

This paper presents a DSP based direct digital control design and implementation for a high power boost converter. A single loop and dual loop voltage control are digitally implemented and compared. The real time workshop (RTW) is used for automatic real-time code generation. Experimental results of a 20 kW boost converter based on the TMS320F2808 DSP during reference voltage changes, input voltage changes, and load disturbances are presented. The results show that the dual loop control achieves better steady state and transient performance than the single loop control. In addition, the experimental results validate the effectiveness of using the RTW for automatic code generation to speed up the system implementation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술회의 논문집 정보 및 제어부문 B
• /
• pp.735-739
• /
• 2003

This paper presents a direct seek control algorithm for swing-arm type dual stage servo system that consists of a coarse actuator and a fine actuator. The proposed scheme is to design a control system that attenuates the effect of dynamic coupling between the two actuators so that the seek operation can be performed in a single-shot with stability. In an optical drive system with dual stage servo mechanism, the effect of dynamic coupling between the two actuators needs to be handled during the coarse seek operation due to its inherent structure. In an extreme case, the two actuators can collide each other, which leads to critical degradation of the seek performance. To handle this problem, our proposed control scheme is to generate the drive signals such that the two actuators behave as if they are a single fixed body. To this end, a feedforward controller and two feedback controllers are designed that enable the current drive system perform wide range of track seek. Simulation results are provided to show the validity and feasibility of our proposed algorithm.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1033-1035
• /
• 2000

This paper presents and analysis a system control algorithm of direct torque control for induction motor using digital signal professor. Using direct torque control, robust. simple and dynamic motor control can be realized. The implemented system is verified by analyzing control torque and flux characteristic.

• 한국측량학회지
• /
• 제23권1호
• /
• pp.77-88
• /
• 2005

Direct Georeferencing을 이용한 항공사진측량 방법에서는 항공기에 탑재한 GPS와 INS로 센서의 위치와 회전각을 정확히 결정함으로써 외부표정요소 결정을 위한 지상기준점 측량을 생략하거나 또는 최소한의 기준점만을 사용하여 외부표정요소를 결정할 수 있다. 따라서 본 연구에서는 측량 시에 항측기에 GPS와 INS 및 CCD 카메라를 탑재하여 동시에 측량을 하고, Direct Georeferencing에 의한 CCD 영상으로 수치정사영상을 제작하여, 수치정사영상의 적용 가능성을 평가하고자 하였다. 본 연구에서 제작된 결과물에 대한 정확도 검증을 위하여 GPS로 측량한 지상 검사점을 기본으로 하여 Direct Georeferencing에 의하여 제작된 수치정사영상의 위치 정확도를 평가하였다. 수치정사영상은 소수의 기준점을 사용한 경우와 기준점을 사용하지 않은 경우의 두 가지로 제작하였다. Direct Georeferencing에 의한 수치정사영상의 제작 작업은 소수의 기준점을 사용하는 경우에 1:1,000 수치지도를 수정·갱신할 수 있으며, 기준점 없이 제작된 정사영상의 경우에는 축척 1:5,000 수치지도를 수정·갱신할 수 있을 것으로 판단된다.