• The Journal of the Acoustical Society of Korea
• /
• v.14 no.2
• /
• pp.5-15
• /
• 1995

An application of the cross correlation technique by adopting ultrasonic waves for water pipe flow measuring purpose is studied. It is a non-intrusive flow metering method by determining the time of the flight of the flow turbulent noise and its non-obstructing mechanism enables to reduce process energy loss due to the flowmeter obstruction. A digital signal processor for the purpose of the real time Fourier transform was employed for the fast time calculation of the flow velocity. The overall accuracy was found as about $1\%$ for flow velocities from 0.25 m/s up to 16 m/s and for the pipe inside diameters from 50mm to 248mm. The cross correlation technique can be used for the tap water utility including most common liquid flows.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.9 no.6
• /
• pp.9-14
• /
• 2009

In this paper, we proposed spreading code slicing technique for efficient transmitter detection in AT-DMB system with single frequency network. At the transmitter, the spreading code for transmitter identification inserted using slicing technique on forehead of null symbol and then transmitted. In this point, it requires high correlation characteristic spreading code. At the receiver, peak to peak value calculated by correlation process before signal demodulation. The transmitter information by proposed technique is employed to implement the single frequency network (SFN) which is proposed for solving a frequency inefficiency problem of the MFN. The results of the paper can be applied to wireless multimedia digital broadcasting system.

• Laser Solutions
• /
• v.5 no.1
• /
• pp.33-42
• /
• 2002

In order to investigate the characteristics of the plasma induced by lap-joint CO$_2$ laser welding of automotive steel sheets, the effects of welding speed, shield gas flow rate, gap size, and laser beam defocus to plasma intensity emitted from keyhole have been investigated. The plasma light is measured by fiber and photodiode. Also, the plasma images were captured by the high speed digital camera in 1000frames/sec in order to correlate the plasma light signal with plasma pattern. From the results, it is observed that the difference of the plasma intensity for between the deep penetration and partial penetration exists from 1.2 to 2 times. The plasma light intensity decreased in case of the deep penetration Is observed due to the exhausting of the plasma gas under the sheet. On the other hand, under the conditions of the deep penetration, the plasma intensity is significantly increased by controling the conditions decreasing the penetration depth. It was specially founded that the effect of 0.3mm gap size at partial penetration condition is approximately similar to deep penetration in 0mm gap. It is concluded that the plasma intensity is able to evaluate the penetration depth in lap-joint welding and appears to offer the most straightforward correlation to the welding process.

• Journal of IKEEE
• /
• v.3 no.2 s.5
• /
• pp.305-313
• /
• 1999

To demodulate the received OFDM signal, symbol timing detection which finds symbol start in the received sample stream is required in the system initialization. In this paper, we analyze the effect of symbol timing offset and propose a new symbol timing detection algorithm, which is using the guard interval. The proposed algorithm requires low computational process and small memory size, and dose not be affected by frequency offset and phase offset. In addition, We apply this algorithm to European digital TV broadcasting model based on OFDM to evaluate the performance in AWGN and multipath fading channel by the computer simulation.

• ETRI Journal
• /
• v.34 no.5
• /
• pp.649-654
• /
• 2012

This paper presents a novel 16-quadrature-amplitude-modulation (QAM) E-band communication system. The system can deliver 10 Gbps through eight channels with a bandwidth of 5 GHz (71-76 GHz/81-86 GHz). Each channel occupies 390 MHz and delivers 1.25 Gbps using a 16-QAM. Thus, this system can achieve a bandwidth efficiency of 3.2 bit/s/Hz. To implement the system, a driver amplifier and an RF up-/down-conversion mixer are implemented using a $0.1{\mu}m$ gallium arsenide pseudomorphic high-electron-mobility transistor (GaAs pHEMT) process. A single-IF architecture is chosen for the RF receiver. In the digital modem, 24 square root raised cosine filters and four (255, 239) Reed-Solomon forward error correction codecs are used in parallel. The modem can compensate for a carrier-frequency offset of up to 50 ppm and a symbol rate offset of up to 1 ppm. Experiment results show that the system can achieve a bit error rate of $10^{-5}$ at a signal-to-noise ratio of about 21.5 dB.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.11
• /
• pp.1-9
• /
• 1996

In the following paper, new architectural algorithm of clock and data recovery circuit is proposed for 622.08 Mbps optical communication receiver. New algorithm makes use of charge pump PLL using voltage controlled ring oscillator and extracts 8-channel 77.76 MHz clock signals, which are delayed by i/8 (i=1,2, ...8), to convert and recover 8-channel parallel data from 662.08 Mbps MRZ serial data. This circuit includes clock genration block to produce clock signals continuously even if input data doesn't exist. And synchronization of data and clock is doen by the method which compares 1/2 bit delayed onput data and decided dta by extracted clock signals. Thus, we can stabilize frequency and phase of clock signal even if input data is distorted or doesn't exist and simplify receiver architecture compared to traditional receiver's. Also it is possible ot realize clock extraction, data decision and conversion simulataneously. Verification of this algorithm is executed by DESIGN CENTER (version 6.1) using test models which are modelized by analog behavior modeling and digital circuit model, modified to process input frequency sufficiently, in SPICE.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.11
• /
• pp.167-174
• /
• 2012

In this paper a ultrasonic oil level meter for measuring oil levels of vehicle transmissions is designed and its effectiveness is shown by experiments. On a FPGA(Field Programmable Gate Array) project IDE(Integrated Development Environment), all digital circuits for the meter is designed using a FPGA, which enables simplicity and high performance of the meter as well as short developing time. Also, power supplying circuit and analog circuits to process low voltage ultrasonic echo signal are designed and simulated. Under experiments, the designed level meter is verified to provide accuracy to within 1mm.

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.57-58
• /
• 2010

This paper proposes maximum torque control of IPMSM drive using optimal current. This control method is applicable over the entire speed range which considered the limits of the inverter's current and voltage rated value. For each control mode, a condition that determines the optimal d-axis current $i_d$ for maximum torque operation is derived. This paper considers the design and implementation of novel technique of high performance speed control for IPMSM using multi-MFC and ANN controller. Also, this paper proposes maximum control of IPMSM drive using approximation method. This method is decreased the burden of digital signal process(DSP) in calculation of optimal current. This paper proposes the analysis results to verify the effectiveness of the MFC and ANN controller. Also it verifies the validity of maximum torque control of IPMSM drive with optimal current.

• Journal of KIISE:Computer Systems and Theory
• /
• v.30 no.12
• /
• pp.749-755
• /
• 2003

Digital signal processing hardware based in RNS is currently considered as an important method for high speed and low cost hardware realization. This research designs and implements the method for conversion from a specific residue number system with moduli of the from $(2^k-1, 2^k, 2^k+1)$ to a weighted number system. Then, it simulates the implementation using a overlapped multiple-bit scanning method in the process of CRT conversion. In conclusion, the simulation shows that the CRT method which is adopted in this research, performs arithmetic operations faster than the traditional approaches, due to advantages of parallel processing and carry-free arithmetic operation.

• Current Optics and Photonics
• /
• v.1 no.2
• /
• pp.90-94
• /
• 2017

Visible light identification (VLID) is a user identification system for a door lock application using smartphone that adopts visible light communication (VLC) technology with the objective of high security, small form factor, and cost effectiveness. The user is verified by the identification application program of a smartphone via fingerprint recognition or password entry. If the authentication succeeds, the corresponding encoded visible light signals are transmitted by a light emitting diode (LED) camera flash. Then, only a small size and low cost photodiode as an outdoor interface converts the light signal to the digital data along with a comparator, and runs the authentication process, and releases the lock. VLID can utilize powerful state-of-the-art hardware and software of smartphones. Furthermore, the door lock system is allowed to be easily upgraded with advanced technologies without its modification and replacement. It can be upgraded by just update the software of smartphone application or replacing the smartphone with the latest one. Additionally, wireless connection between a smartphone and a smart home hub is established automatically via Bluetooth for updating the password and controlling the home devices. In this paper, we demonstrate a prototype VLID door lock system that is built up with LEGO blocks, a photodiode, a comparator circuit, Bluetooth module, and FPGA board.