• Journal of the Korean Wood Science and Technology
• /
• v.17 no.3
• /
• pp.67-81
• /
• 1989

This experiment was carried out to know the mothod of changing the step of moisture content schedule with time in conventional kiln drying. For the purpose of this object. we made drying model by applying the moisture diffusion model by J.FSiau(1984) to average moisture content equation by J.Crank(1956) derived it from Fick's second law. And to verify this method of drying model. 2.5cm-thick boards and 5.0cm-thick dimension lumbers of Pinus densiflora were kiln-dried with the schedule of T11-C3 and T10-C4, respectively. And then the drying rates were investigated and compared with those calculated from drying model. The results obtained were as follows 1. Average drying rate and total drying time of board to dry to 6.5% moisture content were 0.64%/hr and 109hr., and those of dimension lumber to dry to 8.3% moisture content were 0.4%/hr. and 162hr., respectively. 2. The moisture content of shell and core decreased by equalizing treatment and increased by conditioning treatment both on board and dimension lumber. But the moisture gradient was lower after conditioning than after equalizing. 3. As the drying was proceeded, the transverse bound water diffusion coefficient all but linearly decreased, the water vapor diffusion coefficient abruptly curvilinearly increased, while the transverse diffusion coefficient curvilinearly decreased both on board and dimension lumber. But each of diffusion coefficients on board was larger than that on dimension lumber. 4. Compared to experimential drying rate of board. theoretical drying rate was larger at 30.0%-21.8% moisture content range and was similiar at 21.8%-5.4% moisture content. And in case of dimension lumber, the drying rate was similiar at 30.0%-16.1% moisture content range but theoretical drying rate was much lower at 16.1%-8.3% moisture content range. 5. The possibility of adapting this drying model to changing the moisture content schedule step with time was in the range of 21.8%-5.4% moisture content on board. And in the case of dimension lumber that was in the range of 30.0%-16.1% moisture content.

• Journal of Technologic Dentistry
• /
• v.35 no.2
• /
• pp.137-142
• /
• 2013

Purpose: This study was to observe the surface and interfacial characteristic of Zirconia by surface treatment. And it was observed the roughness and contact angle according to processing, and the interfacial properties by surface treatment on zirconia. Methods: The oxide formation and ion diffusion between core and veneer ceramic were determined by the X-ray Dot Mapping of EPMA(Electron probe micro analyzer). The roughness was measured by 3D Digital microscope and the contact angle according to processing of zirconia was observed using distilled water on the surface. Results: The surface roughness of the specimens Z04, Z12, Z15 was measured $0.67({\pm}0.03){\mu}m$, $0.50({\pm}0.12){\mu}m$, $0.35({\pm}0.09){\mu}m$, respectively. As results of contact angle test, Z04, Z12, Z15 of specimen group without binder treatment was measured $46.79({\pm}3.17)^{\circ}$, $57.47({\pm}4.83)^{\circ}$, $56.19({\pm}2.66)^{\circ}$, respectively. but, L04, L12, L15 of specimen group without binder treatment was measured $63.84({\pm}2.20)^{\circ}$, $66.08({\pm}0.16)^{\circ}$, $65.10({\pm}1.01)^{\circ}$, respectively. Average contact angle of L15 was measured $65.10({\pm}1.01)^{\circ}$. In X-ray Dot Mapping results, thickness of binder including Al element was measured that each of L04, L12, L15 were $20{\mu}m$, $15{\mu}m$, $10{\mu}m$. Conclusion: The more rough surface increases the wettability, but the sintered exclusive binder decreases the wettability.

• Journal of the Korean Society for Heat Treatment
• /
• v.32 no.2
• /
• pp.79-85
• /
• 2019

To investigate the influence of heat treatment on the growth intermetallic compounds (IMCs) at the joint interface of friction-welded Cu-Al, several heat treatments are performed at three different temperature with different times. The experiments reveal three different IMCs layers which are significantly influenced by atomic diffusion of Cu and Al with heat treatment conditions. Since the formation of these IMCs layers can affect mechanical properties of friction-welded Cu-Al interfaces, the relationship between the microstructure of IMCs layers and the tensile strength is analyzed according to heat treatment temperature and times.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.3
• /
• pp.327-333
• /
• 1999

Controlled Ca impurity implanted inner crack-like pore in the high purity alumina bi-crystal had been created by micro-fabrication technique, which includes ion implantation, photo-lithography, Ar ion milling, and hot press. The morphological change and the growth od crystals formed by heat treatment in Ca doped high purity single crystal alumina, were observed using optical microscopy. The dot was developed and hexagon like crystal appeared on inner surface of crack-like pore after heat treatment. Bar type crystals, probably CaO . $6Al_2O_3$, were observed on the inner surface of 100ppm Ca implanted specimen after 1 hour heat treatment at $1,500^{\circ}C$, but this bar type crystal disappeared after 1 hour heat treatment at $1,600^{\circ}C$. This disappearance means that there should be little increase of Ca solubility limit to alumina and/or changes of diffusion coefficient of Ca in alumina around this temperature.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.73-82
• /
• 2000

This study was implemented to find an optimal model for wastewater treatment processes using PHOENICS(Parabolic, hyperbolic or Elliptic Numerical Integration Code Series) and ASM(Activated Sludge Model). PHOENICS is a general software based upon the laws of physics and chemistry which govern the motion of fluids, the stresses and strains in solids, heat flow, diffusion, and chemical reaction. The wastewater flow and removal efficiency of particle in two phase system of a grit chamber in wastewater treatment plant were analyzed to inquire the predictive aspect of the operational model. ASM was developed for a biokinetic model based upon material balance in complex activated sludge systems, which can demonstrate dynamic and spatial behavior of biological treatment system. This model was applied to aeration tank and settling chamber in Choonchun city, and the modeling result shows dynamic transport in aeration tank. PHOENCS and ASM could be contributed for the optimal operation of wastewater treatment plant.

• Journal of the Korean Society for Heat Treatment
• /
• v.14 no.2
• /
• pp.81-88
• /
• 2001

The effects of post-oxidation and sulfnitriding treatments on the phase transformation in the nitrided case of tool steels have been studied. Dense and compact $Fe_3O_4$ layer was formed at the outer surface of nitride compound layer by post-oxidation treatment and multi layer of iron sulfide(FeS) was formed in the compound layer by sulfnitriding treatment. The surface hardness decreased because of formation of the soft oxide or sulfide at the nitride surface. Diffusion layer of nitride case was not affected by post-oxidation treatment or sulfnitriding treatment of nitrided alloy tool steels.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 1999.02a
• /
• pp.14-17
• /
• 1999

Four designed $Nb_{3}$Sn superconductors have been fabricated in order to investigate the effect of pre-heat treatment for internal tin process. 3 types of sub-elements and 2 types of Sn reservers were fabricated. Diffusion of Sn is better in the strand divided Sn equally than in the strand had one large Sn reserver during pre heat-treatment.

• Journal of the Korean Professional Engineers Association
• /
• v.15 no.2
• /
• pp.43-44
• /
• 1982

What I would like to expect about this mater is that Korea would develop unique techniques of the waste water which are most suitable to social and other relevant conditions of that country, not entirely following models of sewerage construction of U.S.A. or European countries or Japan. Some cements will be made in the followings: (1) The investigation for the diffusion of seperated simple public sewerag, not the large scale sewerage treatment plant. (2) The plan for non-mixed treatment of lining waste water and industrial waste water. (3) Suggestion for "a man of ability" at the university education to cultivate a technologist of facilities and the elemental watchman at the sewerage maintenance.

• Journal of the Korean Society of Tobacco Science
• /
• v.8 no.2
• /
• pp.43-49
• /
• 1986

Field experiment was conducted to investigate the effect of vinyl mulch on phosphate availability of soil and fertilizer in 1982. Growth of tobacco was more vigorous at each level of phosphate treatment in vinyl mulched than in bare soil. There was significant culture x Phosphorus treatment interaction for the yields of cured tobacco leaves. These results indicated that vinyl mulch was effective to improve phosphate availability of soil and fertilizer. Increase in soil temperature and maintenance of bulk density suitable for Phosphorus diffusion by vinyl mulch were likely to Play major roles on Phosphate availability, but other unknown factors appeared to be involved.

• Journal of Magnetics
• /
• v.18 no.4
• /
• pp.400-404
• /
• 2013

Grain boundary diffusion technique with $DyH_3$ nanoparticles was applied to fabricate Dy-less sintered Nd-Fe-B permanent magnets with high coercivity. The magnetic properties and microstructure of magnets were systematically studied. The coercivity and remanence of grain boundary diffusion magnet were improved by 60% and reduced by 7% compared with those of the original magnet, respectively. Meanwhile, both the remanence temperature coefficient (${\alpha}$) and the coercivity temperature coefficient (${\beta}$) of the magnets were improved after diffusion treatment. Investigation shows that Dy is preferentially enriched as (Nd, Dy)$_2Fe_{14}B$ phase in the surface region of the $Nd_2Fe_{14}B$ matrix grains indicated by the remarkable enhancement of the magneto-crystalline anisotropy field of the magnet. As a result, the magnet diffused with a small amount of Dy nanoparticles possesses enhanced coercivity without remarkably sacrificing its magnetization.